AX2004M uses NMBM on its NAND flash, but it was not enabled in DTS as the
device support [1] had been added before NMBM feature in mtk_bmt driver [2].
Let's enable it now.
With this change, there is a low possibility of boot failure after
sysupgrade from older versions. As AX2004M already has gone through
two stable releases in the meantime, it would be safe to warn users
by bumping DEVICE_COMPAT_VERSION.
[1] 37753f34ac ("ramips: add support for ipTIME AX2004M")
[2] 06382d1af7 ("kernel: add support for mediatek NMBM flash mapping support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Rostelecom RT-FE-1A is a wireless WiFi 5 router manufactured by Sercomm
company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: No
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Power (green, unmanaged)
- 1x Status (green, gpio)
- 1x 2.4G (green, hardware, mt76-phy0)
- 1x 2.4G (blue, gpio)
- 1x 5G (green, hardware, mt76-phy1)
- 1x 5G (blue, gpio)
- 5x Ethernet (green, hardware, 4x LAN & WAN)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface (default http://192.168.0.1/)
under "admin" account
2. Navigate to Settings -> Configuration -> Save to Computer
3. Decode the configuration. For example, using cfgtool.py tool (see
related section):
cfgtool.py -u configurationBackup.cfg
4. Open configurationBackup.xml and find the following block:
<OBJECT name="User." type="object" writable="1" encryption="0" >
<OBJECT name="1." type="object" writable="1" encryption="0" >
<PARAMETER name="Password" type="string" value="<some value>" writable="1" encryption="1" password="1" />
</OBJECT>
5. Replace <some value> by a new superadmin password and add a line
which enabling superadmin login after. For example, the block after
the changes:
<OBJECT name="User." type="object" writable="1" encryption="0" >
<OBJECT name="1." type="object" writable="1" encryption="0" >
<PARAMETER name="Password" type="string" value="s0meP@ss" writable="1" encryption="1" password="1" />
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
</OBJECT>
6. Encode the configuration. For example, using cfgtool.py tool:
cfgtool.py -p configurationBackup.xml
7. Upload the changed configuration (configurationBackup_changed.cfg) to
the router
8. Login to the router web interface (superadmin:xxxxxxxxxx, where
xxxxxxxxxx is a new password from the p.5)
9. Enable SSH access to the router (Settings -> Access control -> SSH)
10. Connect to the router using SSH shell using superadmin account
11. Run in SSH shell:
sh
12. Make a mtd backup (optional, see related section)
13. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
14. Login to the router web interface under admin account
15. Remove dots from the OpenWrt factory image filename
16. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 192.168.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 192.168.0.2
MAC Addresses
-------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | f4:*:66 |
| WAN | label + 11 | f4:*:71 |
| 2g | label + 2 | f4:*:68 |
| 5g | label + 3 | f4:*:69 |
+-----+------------+---------+
The label MAC address was found in Factory, 0x21000
cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
This device is very similar, if not identical, to the TP-Link AX23 v1
but is targeted at service providers and features a completely different
flash layout.
Hardware
--------
CPU: MediaTek MT7621 DAT
RAM: 128MB DDR3 (integrated)
FLASH: 16MB SPI-NOR
WiFi: MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax
SERIAL: 115200 8N1
LEDs - (3V3 - GND - RX - TX) - ETH ports
Installation
------------
Flashing is only possible via a serial connection using the sysupgrade
image; the factory image must be signed. You can flash the sysupgrade
image directly through the U-Boot console, or preferably, by booting the
initramfs image and flashing with the sysupgrade command. Follow these
steps for sysupgrade flashing:
1. Establish a UART serial connection.
2. Set up a TFTP server at 192.168.0.2 and copy the initramfs image
there.
3. Power on the device and press any key to interrupt normal boot.
4. Load the initramfs image using tftpboot.
5. Boot with bootm.
6. If you haven't done so already, back up all stock mtd partitions.
7. Copy the sysupgrade image to the router.
8. Flash OpenWrt through either LuCI or the sysupgrade command. Remember
not to attempt saving settings.
Revert to stock firmware
------------------------
Flash stock firmware via OEM web-recovery mode. If you don't have access
to the stock firmware image, you will need to restore the firmware
partition backed up earlier.
Web-Recovery
------------
The router supports an HTTP recovery mode:
1. Turn off the router.
2. Press the reset button and power on the device.
3. When all LEDs start flashing, release reset and quickly press it
again.
The interface is reachable at 192.168.0.1 and supports installation of
the OEM factory image. Note that flashing OpenWrt this way is not
possible, as mentioned above.
Signed-off-by: Darlan Pedro de Campos <darlanpedro@gmail.com>
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7603E, MediaTek MT7613BE
- Switch: 1 WAN, 4 LAN (Gigabit)
- Buttons: Reset, WPS
- LEDs: System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS
- Power: DC 12V 1A tip positive
Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.
Cudy WR1300 v3 differs from v2 only in swapped WiFi chip PCIe slots. Common
nodes are extracted to .dtsi and new v2 and v3 dts are created.
Cudy WR1300 v2 dts now contains ieee80211-freq-limit and has
eeprom_factory_8000 length fixed.
The same manufacturer's built OpenWRT image is provided for both v2 and v3
devices as a step in installing, but for proper WiFi functionality,
a separate build is required.
Recovery:
- Loads only signed manufacture firmware due to bootloader RSA verification
- serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
- connect to any lan ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button for image to
download
- See http://www.cudytech.com/newsinfo/547425.html
Signed-off-by: Filip Milivojevic <zekica@gmail.com>
This commit makes a common recipe to set bit in Sercomm factory pid since
this is necessary for several devices (WiFire S1500.nbn, Rostelecom
RT-FL-1) at different offsets.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Three fixes for D-Link DAP-1620 rev B and its twin D-Link DRA-1360:
1. `uboot-envtools` is removed from default package list.
2. Makefile variable is doubly escaped, i.e. `$$$$(DLINK_HWID)`.
3. Previously the size of `factory.bin` was always 10.5 MiB, same as
D-Link firmwares. This commit makes it possible to use smaller images
(with no lost space due to padding) as well as larger images. Tested
successfully flashing a 6.5 MiB image and a 14.5 MiB image.
Recall that factory images need to be installed via D-Link Web Recovery
(at http://192.168.0.50/, server ignores pings and DHCP requests).
P.S.
I implemented the OEM firmware encryption algorithm, so firmware can be
flashed via OEM firmware, but after successful flashing the device
reboots to web recovery, so further debugging is required.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
The COVR-X1860 are MT7621-based AX1800 devices (similar to DAP-X1860, but
with two Ethernet ports and external power supply) that are sold in sets
of two (COVR-X1862) and three (COVR-X1863).
Specification:
- MT7621
- MT7915 + MT7975 2x2 802.11ax (DBDC)
- 256MB RAM
- 128 MB flash
- 3 LEDs (red, orange, white), routed to one indicator in the top of the device
- 2 buttons (WPS in the back and Reset at the bottom of the device)
MAC addresses:
- LAN MAC (printed on the device) is stored in config2 partition as ASCII (entry factory_mac=xx:xx:xx:xx:xx:xx)
- WAN MAC: LAN MAC + 3
- 2.4G MAC: LAN MAC + 1
- 5G MAC: LAN MAC + 2
The pins for the serial console are already labeled on the board (VCC, TX, RX, GND). Serial settings: 3.3V, 115200,8n1
Flashing via OEM Web Interface:
- Download openwrt-ramips-mt7621-dlink_covr-x1860-a1-squashfs-factory.bin via the OEM web interface firmware update
- The configuration wizard can be skipped by directly going to http://192.168.0.1/UpdateFirmware_Simple.html
Flashing via Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the status LED blinks red
- Open a Chromium based browser and goto http://192.168.0.1
- Download openwrt-ramips-mt7621-dlink_covr-x1860-a1-squashfs-recovery.bin
Revert back to stock using the Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.25
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the status LED blinks red
- Open a Chromium based browser and goto http://192.168.0.1
- Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.
Decrypting a D-Link firmware image:
- Download https://github.com/openwrt/firmware-utils/blob/master/src/dlink-sge-image.c and https://raw.githubusercontent.com/openwrt/firmware-utils/master/src/dlink-sge-image.h
- Compile a binary from the downloaded file, e.g. gcc dlink-sge-image.c -lcrypto -o dlink-sge-image
- Run ./dlink-sge-image COVR-X1860 <OriginalFirmware> <OutputFile> -d
- Example for firmware 102b01: ./dlink-sge-image COVR-X1860 COVR-X1860_RevA_Firmware_102b01.bin COVR-X1860_RevA_Firmware_102b01_Decrypted.bin -d
The pull request is based on the discussion in https://forum.openwrt.org/t/add-support-for-d-link-covr-x1860
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
This fixes a well known "LZMA ERROR 1" error on Sercomm NA502,
reported on the OpenWrt forum. [1]
[1]: https://forum.openwrt.org/t/176942
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
creates SGE encrypted factory images
to use via the D-Link web interface
rename the old factory unencrypted images to recovery
for use in the recovery console when recovery is needed
DIR-1935-A1 , DIR-853-A1 , DIR-853-A3 , DIR-867-A1 ,
DIR-878-A1 and DIR-882-A1
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
Hardware:
- SoC: Mediatek MT7621 (MT7621AT)
- Flash: 32 MiB SPI-NOR (Macronix MX25L25635E)
- RAM: 128 MiB
- Ethernet: Built-in, 2 x 1GbE
- 3G/4G Modem: MEIG SLM828 (currently only supported with ModemManager)
- SLIC: Si32185 (unsupported)
- Power: 12V via barrel connector
- Wifi 2.4GHz: Mediatek MT7603BE 802.11b/g/b
- Wifi 5GHz: Mediatek MT7613BE 802.11ac/n/a
- LEDs: 8x (7 controllable)
- Buttons: 2x (RESET, WPS)
Installing OpenWrt:
- sysupgrade image is compatible with vendor firmware.
Recovery:
- Connect to any of the Ethernet ports, configure local IP:
10.10.10.3/24 (or 192.168.10.19/24, depending on OEM)
- Provide firmware file named 'mt7621.img' on TFTP server.
- Hold down both, RESET and WPS, then power on the board.
- Watch network traffic using tcpdump or wireshark in realtime to
observe progress of device requesting firmware. Once download has
completed, release both buttons and wait until firmware comes up.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Telco Electronics X1 has MT7603E and MT7612E PCIe NICs. They are
driven by kmod-mt7603 and kmod-mt76x2.
Ref: 73e0f52b6e ("ramips: add support for Telco Electronics X1")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Add support for COMFAST CF-EW72 V2
Hardware:
- SoC: Mediatek MT7621 (MT7621DAT or MT7621AT)
- Flash: 16 MiB NOR
- RAM: 128 MiB
- Ethernet: Built-in, 2 x 1GbE
- Power: only 802.3af PD on any port, injector supplied in the box
- PoE passthrough: No
- Wifi 2.4GHz: Mediatek MT7603BE 802.11b/g/b
- Wifi 5GHz: Mediatek MT7613BEN 802.11ac/n/a
- LEDs: 8x (only 1 is both visible and controllable, see below)
- Buttons: 1x (RESET)
Installing OpenWrt:
Flashing is done using Mediatek U-Boot System Recovery Mode
- make wired connection with 2 cables like this:
- - PC (LAN) <-> PoE Injector (LAN)
- - PoE Injector (POE) <-> CF-EW72 V2 (LAN). Leave unconnected to CF-EW72 V2 yet.
- configure 192.168.1.(2-254)/24 static ip address on your PC LAN
- press and keep pressed RESET button on device
- power the device by plugging PoE Injector (POE) <-> CF-EW72 V2 (LAN) cable
- wait for about 10 seconds until wifi led stops blinking and release RESET button
- navigate from your PC to http://192.168.1.1 and upload OpenWrt *-factory.bin firmware file
- proceed until router starts blinking with wifi led again (flashing) and stops (rebooting to OpenWrt)
MAC addresses as verified by OEM firmware:
vendor OpenWrt address
LAN lan\eth0 label
WAN wan label + 1
2g phy0 label + 2
5g phy1 label + 3
The label MAC address was found in 0xe000.
LEDs detailed:
The only both visible and controllable indicator is blue:wlan LED.
It is not bound by default to indicate activity of any wireless interfaces.
Place (WAN->ANT) | Num | GPIO | LED name (LuCI) | Note
-----------------|-----|-----------------------------------------------------------------------------------------
power | 1 | | | POWER LED. Not controlled with GPIO.
hidden_led_2 | 2 | 13 | blue:hidden_led_2 | This LED does not have proper hole in shell.
wan | 3 | | | WAN LED. Not controlled with GPIO.
hidden_led_4 | 4 | 16 | blue:hidden_led_4 | This LED does not have proper hole in shell.
lan | 5 | | | LAN LED. Not controlled with GPIO.
noconn_led_6 | 6 | | | Not controlled with GPIO, possibly not connected
wlan | 7 | 15 | blue:wlan | WLAN LED. Wireless indicator.
noconn_led_8 | 8 | | | Not controlled with GPIO, possibly not connected
mt76-phy0 and mt76-phy1 leds also exist in OpenWrt, but do not exist on board.
Signed-off-by: Alexey D. Filimonov <alexey@filimonic.net>
This commit removes the padded zeros in the date formatting.
The padded zeros from the date command causes the numbers
to be interpreted as an octal number by printf. Months, days,
and years with the number 08 or 09 raise an error in printf as an
"invalid octal number" and get interpreted as a zero.
Signed-off-by: Max Qian <public@maxqia.com>
ALFA Network AX1800RM (FCC ID: 2AB877621) is a dual-band Wi-Fi 6
(AX1800) router, based on MediaTek MT7621A + MT79x5D platform.
Specifications:
- SOC: MT7621A (880 MHz)
- DRAM: DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash: 16 MiB SPI NOR (EN25QH128A-104HIP)
- Ethernet: 4x 10/100/1000 Mbps (SOC's built-in switch)
- Wi-Fi: 2x2:2 2.4/5 GHz (MT7905DAN + MT7975DN)
(MT7905DAN doesn't support background DFS scan/BT)
- LED: 6x green, 1x green/red
- Buttons: 2x (reset, WPS)
- Antenna: 4x external, non-detachable omnidirectional
- UART: 1x 4-pin (2.54 mm pitch, J4, not populated)
- Power: 12 V DC/1 A (DC jack)
MAC addresses:
LAN: 00:c0:ca:xx:xx:4e (factory 0x4, +2)
WAN: 00:c0:ca:xx:xx:4f (factory 0x4, +3)
2.4 GHz: 00:c0:ca:xx:xx:4c (factory 0x4, device's label)
5 GHz: 00:c0:ca:xx:xx:4c (factory 0xa)
Flash instructions for web-based U-Boot recovery:
1. Power the device with WPS button pressed and wait around 10 seconds.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'recovery' image.
The device runs LEDE 17.01 (kernel 4.4.x) based firmware with 'failsafe'
mode available which allows alternative upgrade method:
1. Run device in 'failsafe' mode and change password for default user.
2. SSH to the device, transfer 'sysupgrade' image and perform upgrade
in forced mode, without preserving settings: 'sysupgrade -n -F ...'.
Other notes:
If you own early version of this device, the vendor firmware might
refuse OpenWrt image because of missing custom header. In that case,
ask vendor's customer support for stock firmware without custom header
support/requirement.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The DRA-1360 rev A is a wall-plug AC1300 repeater.
Hardware is identical (same FCC ID, black case instead of white)
to D-Link DAP-1620 rev B, which is already supported, but a
different model name, revision, and hardware ID are needed.
Thus, the bulk of the DAP-1620 device tree is extracted to a
common dtsi included by the two models' device trees.
Repeating specs and installation instructions from e4c7703:
(note that the RAM size mentioned there was incorrect, oops)
Specs:
- SoC: MT7621AT (880MHz dual-core MIPS1004Kc)
- Memory: 128 MiB RAM, 16 MiB NOR SPI
- WiFi: MT7615DN 2x2 802.11n + 2x2 802.11ac (DBDC)
- Ethernet: 1 RJ45 port 10/100/1000
- Power/status LED: red+green
- LED RSSI bargraph: 2x green, 1x red+green
Installation:
- Keep reset button pressed during plug-in
- Web Recovery Updater is at 192.168.0.50
(pings are ignored, it listens only for http)
- Upload factory.bin, confirm flashing
(seems to work best with Chromium-based browsers)
Revert to OEM firmware:
- tail -c+117 DRA1360A1_FW112B03.bin | \
openssl aes-256-cbc -d -md md5 -out decrypted.bin \
-k c471706398cb147c6619f8a04a18d53e9c17ede8
- flash decrypted.bin via D-Link Web Recovery
Signed-off-by: Rani Hod <rani.hod@gmail.com>
I-O DATA WN-DEAX1800GR is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based
on MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash : RAW NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN : 2.4/5 GHz (MediaTek MT7915)
- Ethernet : 5x 10/100/1000 Mbps
- Switch : MT7530 (SoC)
- LEDs/Keys : 6x/3x
- UART : through-hole on PCB (J2)
- assignment: 3.3V, GND, TX, RX from "1" marking
- settings : 115200n8
- Power : 12 VDC, 1 A
Flash instruction using initramfs-factory image:
1. Boot WN-DEAX1800GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button to perform firmware update
4. On the initramfs image, perform sysupgrade with the
squashfs-sysupgrade.bin image
5. Wait ~120 seconds to complete flashing
Note:
- This device has 2x OS images on the flash storage. In this support,
the first one will be used.
Warning:
- Do not use "saveenv" command on U-Boot CLI.
This device has wrong u-boot-env data. The actual length of individual
env data installed to the device is 0x1000 (4 KiB), but installed
U-Boot requires 0x20000 (128 KiB). So U-Boot determines the data is
invalid. Then, if you perform saving environment data with saveenv on
U-Boot CLI, installed env data will be overwritten with too few
default values without individual values (SSID, password, MAC
addresses, etc...).
MAC addresses:
LAN : 50:41:B9:xx:xx:F4 (Config, ethaddr (text))
WAN : 50:41:B9:xx:xx:F6 (Config, wanaddr (text))
2.4 GHz: 50:41:B9:xx:xx:F4 (Config, rmac (text) / Factory, 0x4 (hex))
5 GHz : 50:41:B9:xx:xx:F5 (none)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Rename GB-PC1 to GnuBee GB-PC1, and GB-PC2 to GnuBee GB-PC2. Let's not make
naming exceptions because of marketing whims.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
The TP-Link EAP613 v1 is a ceiling-mount 802.11ax access point. It can
be powered via PoE or a DC barrel connector (12V). Connecting to the
UART requires fine soldering and careful manipulation of any soldered
wires.
Device details:
* SoC: MT7621AT
* Flash: 16 MiB SPI NOR
* RAM: 256 MiB DDR3L
* Wi-Fi:
* MT7905DA + MT7975D: 2.4 GHz + 5 GHz (DBDC), 2x2:2
* Two stamped metal antennas (ANT1, ANT2)
* One PCB antenna (ANT3)
* One unpopulated antenna (ANT4)
* Ethernet:
* 1× 10/100/1000 Mbps port with PoE
* LEDs:
* Array of four blue LEDs with one control line
* Buttons:
* Reset
* Board test points:
* UART: next to CPU RF-shield and power circuits
* JTAG: under CPU RF-shield (untested)
* Watchdog: 3PEAK TPV706 (not implemented)
Althought three antennas are populated, the MT7905DA does not support
the additional Rx chain for background DFS detection (or Bluetooth)
according to commit 6cbcc34f50 ("ramips: disable unsupported
background radar detection").
MAC addresses:
* LAN: 48:22:54:xx:xx:a2 (device label)
* WLAN 2.4 GHz: 48:22:54:xx:xx:a2
* WLAN 5 GHz: 48:22:54:xx:xx:a3
The radio calibration blob stored in flash also contains valid MAC
addresses for both radio bands (OUI 00:0c:43).
Factory install:
1. Enable SSH on the device via web interface
2. Log in with SSH, and run `cliclientd stopcs`
3. Upload -factory.bin image via web interface. It may be necessary to
shorten the filename of the image to e.g. 'factory.bin'.
Recovery:
1. Open the device by unscrewing four screws from the backside
2. Carefully remove board from the housing
3. Connect to UART (3.3V):
* Find test points labelled "VCC", "GND", "UART_TX", "UART_RX"
* Solder wires to test points or connect otherwise. Be careful not
to damage the PCB e.g. by pulling on soldered wires.
* Open console with 115200n8 settings
4. Interrupt bootloader and use tftpboot to start an initramfs:
setenv ipaddr $DEVICE_IP
setenv serverip $SERVER_IP
tftpboot 84000000 openwrt-initramfs-kernel.bin
bootm
DO NOT use saveenv to store modified u-boot environment variables. The
environment is saved at flash offset 0x30000, which erases part of the
(secondary) bootloader.
The device uses two bootloader stages. The first stage will load the
second stage from a uImage stored at flash offset 0x10000. In case of
a damaged second stage, the first stage should allow uploading a new
image via y-modem (untested).
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Add support for ComFast CF-E390AX. It is a 802.11 wifi6 cieling AP, based on MediaTek MT7261AT.
Specifications:
SoC: MediaTek MT7621AT
RAM: 128 MiB
Flash: 16 MiB NOR (Macronix mx25l12805d)
Wireless: MT7915E (2.4G) 802.11ax/b/g/n MT7915E (5G) 802.11ac/ax/n
Ethernet: 2 x 1Gbs
Button: 1 x "Reset" button
LED: 1x Blue LED + 1x Red LED + 1x green LED
Power: PoE
Manufacturer Page:
http://en.comfast.com.cn/index.php?m=content&c=index&a=show&catid=84&id=75
Flash Layout:
0x000000000000-0x000000030000 : "bootloader"
0x000000030000-0x000000040000 : "config"
0x000000050000-0x000000060000 : "factory"
0x000000090000-0x000001000000 : "firmware"
First install:
1. Set device into http firmware fail safe upload mode by pressing the reset button for 10 seconds while powering
it on. Once the LED stops flashing, safe mode will be running.
2. Set PC IP address to 192.168.1.2
3. Browse to 192.168.1.1 and upload the factory image using the web interface.
Signed-off-by: Usama Nassir <usama.nassir@gmail.com>
This commit adds support for following wireless routers:
- Beeline SmartBox PRO (Serсomm S1500 AWI)
- WiFire S1500.NBN (Serсomm S1500 BUC)
This commit is based on this PR:
- Link: https://github.com/openwrt/openwrt/pull/4770
- Author: Maximilian Weinmann <x1@disroot.org>
The opening of this PR was agreed with author.
My changes:
- Sorting, minor changes and some movings between dts and dtsi
- Move leds to dts when possible
- Recipes for the factory image
- Update of the installation/recovery/return to stock guides
- Add reset GPIO for the pcie1
Common specification
--------------------
SoC: MediaTek MT7621AT (880 MHz, 2 cores)
Switch: MediaTek MT7530 (via SoC MT7621AT)
Wireless: 2.4 GHz, MT7602EN, b/g/n, 2x2
Wireless: 5 GHz, MT7612EN, a/n/ac, 2x2
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
Mini PCIe: via J2 on PCB, not soldered on the board
UART: J4 -> GND[], TX, VCC(3.3V), RX
BootLoader: U-Boot SerComm/Mediatek
Beeline SmartBox PRO specification
----------------------------------
RAM (Nanya NT5CB128M16FP): 256 MiB
NAND-Flash (ESMT F59L2G81A): 256 MiB
USB ports: 2xUSB2.0
LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP)
Power: 12 VDC, 1.5 A
PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0
CSN: SG15********
MAC LAN: 94:4A:0C:**:**:**
Manufacturer's code: 0AWI0500QW1
WiFire S1500.NBN specification
------------------------------
RAM (Nanya NT5CC64M16GP): 128 MiB
NAND-Flash (ESMT F59L1G81MA): 128 MiB
USB ports: 1xUSB2.0
LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (RESET, WPS)
Power: 12 VDC, 1.0 A
PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0
CSN: MH16********
MAC WAN: E0:60:66:**:**:**
Manufacturer's code: 0BUC0500RW1
MAC address table (PRO)
-----------------------
use address source
LAN *:23 factory 0x1000 (label)
WAN *:24 factory $label +1
2g *:23 factory $label
5g *:25 factory $label +2
MAC addresses (NBN)
-------------------
use address source
LAN *:0e factory 0x1000
WAN *:0f LAN +1 (label)
2g *:0f LAN +1
5g *:10 LAN +2
OEM easy installation
---------------------
1. Remove all dots from the factory image filename (except the dot
before file extension)
2. Upload and update the firmware via the original web interface
3. Two options are possible after the reboot:
a. OpenWrt - that's OK, the mission accomplished
b. Stock firmware - install Stock firmware (to switch booflag from
Sercomm0 to Sercomm1) and then OpenWrt factory image.
Return to Stock
---------------
1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2
reboot
2. Install stock firmware via the web OEM firmware interface
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
Tested-by: Pavel Ivanov <pi635v@gmail.com>
Tested-by: Denis Myshaev <denis.myshaev@gmail.com>
Tested-by: Oleg Galeev <olegingaleev@gmail.com>
Tested-By: Ivan Pavlov <AuthorReflex@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Netgear EAX12, EAX11v2, EAX15v2 are wall-plug 802.11ax (Wi-Fi 6)
extenders that share the SoC, WiFi chip, and image format with the
WAX202.
Specifications:
* MT7621, 256 MiB RAM, 128 MiB NAND
* MT7915: 2.4/5 GHz 2x2 802.11ax (DBDC)
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)
All LEDs and buttons appear to work without state_default.
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References in GPL source:
https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz
* target/linux/ramips/dts/mt7621-rfb-ax-nand.dts
DTS file for this device.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Zbtlink ZBT-WG1608 is a Wi-Fi router intendent to use with WWAN (4G/5G)
modems.
Specifications:
* SoC: MediaTek MT7621A
* RAM: 256/512 MiB
* Flash: 16/32 MiB (SPI NOR)
* Wi-Fi:
* MediaTek MT7603E : 2.4Ghz
* MediaTek MT7613BE : 5Ghz
* Ethernet: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
* M.2: 1x slot with USB&SIM
* EM7455/EM12-G/EM160R/RM500Q-AE
* USB: 1x 3.0 Type-A port
* External storage: 1x microSD (SDXC) slot
* UART: console (115200 baud)
* LED:
* 1 power indicator
* 1 WLAN 2.4G controlled (wlan 2G)
* 3 SoC controlled (wlan 5G, wwan, internet)
* 5 per Eth phy (4xLAN + WAN)
MAC Addresses:
* LAN : f8:5e:3c:xx:xx:e0 (Factory, 0xe000 (hex))
* WAN : f8:5e:3c:xx:xx:e1 (Factory, 0xe006 (hex))
* 2.4 GHz: f8:5e:3c:xx:xx:de (Factory, 0x0004 (hex))
* 5 GHz : f8:5e:3c:xx:xx:df (Factory, 0x8004 (hex))
Installation:
* Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can
be directly used to install OpenWrt. Firmware must be upgraded using the
'force' and 'do not save configuration' command line options (or
correspondig web interface checkboxes) since the vendor firmware is from
the pre-DSA era.
Recovery Mode:
* Press reset button, power up the device, wait for about 10sec.
* Upload sysupgrade image through the firmware recovery mode web page at
192.168.1.1.
Signed-off-by: Kim DoHyoung <azusahmr@k-on.kr>
This adds support for Beeline Smart Box TURBO+ (Serсomm S3 CQR) router.
Device specification
--------------------
SoC Type: MediaTek MT7621AT (880 MHz, 2 cores)
RAM (Nanya NT5CC64M16GP): 128 MiB
Flash (Macronix MX30LF1G18AC): 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615N): a/n/ac, 4x4
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
USB ports: 1xUSB3.0
Buttons: 2 button (reset, wps)
LEDs: Red, Green, Blue
Zigbee (EFR32MG1B232GG): 3.0
Stock bootloader: U-Boot 1.1.3
Power: 12 VDC, 1.5 A
Installation (fw 2.0.9)
-----------------------
1. Login to the web interface under SuperUser (root) credentials.
Password: SDXXXXXXXXXX, where SDXXXXXXXXXX is serial number of the
device written on the backplate stick.
2. Navigate to Setting -> WAN. Add:
Name - WAN1
Connection Type - Static
IP Address - 172.16.0.1
Netmask - 255.255.255.0
Save -> Apply. Set default: WAN1
3. Enable SSH and HTTP on WAN. Setting -> Remote control. Add:
Protocol - SSH
Port - 22
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN Interface - WAN1
Save ->Apply
Add:
Protocol - HTTP
Port - 80
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN interface - WAN1
Save -> Apply
4. Set up your PC ethernet:
Connection Type - Static
IP Address - 172.16.0.2
Netmask - 255.255.255.0
Gateway - 172.16.0.1
5. Connect PC using ethernet cable to the WAN port of the router
6. Connect to the router using SSH shell under SuperUser account
7. Make a mtd backup (optional, see related section)
8. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
9. Login to the router web interface under admin account
10. Remove dots from the OpenWrt factory image filename
11. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 172.16.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 171.16.0.2
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses (fw 2.0.9)
------------------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:e8 |
| WAN | label + 1 | *:e9 |
| 2g | label + 4 | *:ec |
| 5g | label + 5 | *:ed |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
Factory image format
--------------------
+---+-------------------+-------------+--------------------+
| # | Offset | Size | Description |
+---+-------------------+-------------+--------------------+
| 1 | 0x0 | 0x200 | Tag Header Factory |
| 2 | 0x200 | 0x100 | Tag Header Kernel1 |
| 3 | 0x300 | 0x100 | Tag Header Kernel2 |
| 4 | 0x400 | SIZE_KERNEL | Kernel |
| 5 | 0x400+SIZE_KERNEL | SIZE_ROOTFS | RootFS(UBI) |
+---+-------------------+-------------+--------------------+
Co-authored-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
The MR600v2 does not find its rootfs if it is neither directly after the
kernel or aligned to an erase block boundary (64k).
This aligns the rootfs to 0x10000 allowing the device to boot again. Based
on investigation by forum user relghuar.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
These same codes are repeated for many devices now, it's better to
move them to shared definition. This commit also add the missing
KERNEL_SIZE of the ZyXEL NR7101 and ZyXEL LTE3301-PLUS.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
In kernel 5.15, the default erase sector size of the nor flash has
been switched from 4k to 64k. This may cause the configuration not
be preserved across upgrades. To avoid this issue, change the default
BLOCKSIZE to 64k.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Rename Newifi D2 to D-Team Newifi D2, and Newifi D1 to Lenovo Newifi D1.
Let's not make naming exceptions because of marketing whims.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
The TOZED ZLT S12 PRO is an AC1200 router featuring 4 Ethernet ports with a
TOZED TL70-C cellular modem which supports the NCM mode.
The stock firmware does SIM locking on the modem by stopping dialing when a
different PLMN is detected. This is not the case on OpenWrt.
Specifications:
- CPU: MediaTek MT7621AT
- RAM: 256MB DDR3
- NOR Flash: MX25L12833FM2I 16MB SPI Flash
- Wi-Fi 2.4Ghz: MT7603E
- Wi-Fi 5Ghz: MT7612E
- Switch: MT7530 4x 1Gbit Ports
- WWAN: Unisoc SL8563 based TOZED TL70-C LTE CAT6 cellular modem
- USB: 1x optional USB2.0 external port
- Switches/Buttons: WPS, Reset, Power Switch
- LEDs: Power, Wi-Fi, Data, Signal 1-5, Phone
Installation and TFTP Recovery:
- Connect to serial console.
- Boot initramfs image by choosing option 1 when U-Boot prompts.
- Install sysupgrade image via OpenWrt.
Serial Pins:
Located at the bottom right when looking from the front, right under the
Reset/WPS buttons. The pinout from the left is:
- RX
- GND
- TX
Baudrate is 115200.
When connecting from a powered off state, disconnect RX as it blocks the
boot process.
Link: http://www.sztozed.com/en/contents/58/84.html
Co-developed-by: Andre Cruz <me@1conan.com>
Signed-off-by: Andre Cruz <me@1conan.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Hardware specification:
- SoC: MediaTek MT7621AT (880 MHz)
- Flash: 16 MB (Macronix MX25L12835FM2I-10G)
- RAM: 128 MB (Nanya NT5CC64M16GP-DI)
- WLAN 2.4 GHz: 2x2 MediaTek MT7603EN
- WLAN 5 GHz: 2x2 MediaTek MT7615N
- Ethernet: 1x 10/100/1000 Mbps
- LED: Power, Wifi, WPS
- Button: Reset, WPS
- UART: 1:VCC, 2:GND, 3:TX, 4:RX (from LAN port)
Serial console @ 57600,8n1
Flash instructions:
Connect to serial console and start up the device. As the bootloader got
locked you need to type in a password to unlock U-Boot access.
When you see the following output on the console:
relocate_code Pointer at: 87f1c000
type in the super secure password:
1234567890
Then select TFTP boot from RAM by selecting option 1 in the boot menu.
As Linksys decided to leave out a basic TFTP configuration you need to
set server- & client ip as well as the image filename the device will
search for. You need to use the initramfs openwrt image for the TFTP
boot process.
Once openwrt has booted up, upload the sysupgrade image via scp and run
sysupgrade as normal.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Rename existing device to v1 and create common .dtsi
Difference to v1: 16MB Flash
Specifications:
SoC: MediaTek MT7621
RAM: 256 MB
Flash: 16 MB (SPI NOR, XM25QH128C on my device)
WiFi: MediaTek MT7915E
Switch: 1 WAN, 4 LAN (Gigabit)
Buttons: Reset, WPS
LEDs: Two Power LEDs (blue and red; together they form purple)
Power: DC 12V 1A center positive
Serial: 115200 8N1
C440 - (3V3 - GND - RX - TX) - C41 | v1 and v2
(P - G - R - T) | v2 labels them on the board
Installation:
Download and flash the manufacturer's built OpenWrt image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWrt image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings.
Recovery:
Loads only signed manufacture firmware due to bootloader RSA verification
Serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
Connect to any lan ethernet port
Power on the device while holding the reset button
Wait at least 8 seconds before releasing reset button for image to
download
MAC addresses as verified by OEM firmware:
use address source
LAN f4:a4:54:86:75:a2 label
WAN f4:a4:54:86:75:a3 label + 1
2g f4:a4:54:86:75:a2 label
5g f6:a4:54:b6:75:a2 label + LA-Bit set + 4th oktet increased
The label MAC address is found in bdinfo 0xde00.
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
This commit adds factory.bin image for TP-Link EC330-G5u v1. This allows
to install OpenWrt without connecting a serial cable (UART).
Installation using factory image
--------------------------------
Tested with "3.16.0 0.9.1 v6037.0 Build 191016 Rel.30619nb" TP-Link
firmware.
1. Login to the router web interface (http://192.168.0.1/ by default) and
save running config to "conf.bin" file
2. Open configuration file in any TP-Link config editor (e.g.
https://jahed.github.io/tp-link-config-editor/)
3. Find "DeviceInfo" section and insert a new string "<Description
val="Modem Router`telnetd -p 1023 -l login`" />" according to the
following example:
<DeviceInfo>
...
<Description val="Modem Router`telnetd -p 1023 -l login`" />
...
</DeviceInfo>
4. Save configuration file and upload changed configuration using stock
firmware interface
5. Login using telnet to IP:192.168.0.1 (Username:admin, password:1234)
6. Run "cat /proc/mtd | grep mtd7"
a. If the result is 'mtd7: 03000000 00020000 "rootfs" 03400000',
then install stock firmware using web interface to toggle booted
firmware image from "os1" to "os0"
b. If the result is 'mtd7: 03000000 00020000 "rootfs" 00400000',
then all is ok, go to the next step
7. Set up a tftp server with OpenWrt factory.bin image (IP:192.168.0.100
in this example)
8. Login using telnet to 192.168.0.1
9. Download OpenWrt factory.bin image from the tftp server:
cd /tmp
tftp -g -r factory.bin 192.168.0.100
10. Write OpenWrt factory.bin image:
dd if=/tmp/factory.bin of=/dev/mtdblock1
11. Power cycle the router
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
The ZyXEL WSM20 aka Multy M1 is a cheap mesh router system by ZyXEL
based on the MT7621 CPU.
Specifications
==============
SoC: MediaTek MT7621AT (880MHz)
RAM: 256MiB
Flash: 128MiB NAND
Wireless: 802.11ax (2x2 MT7915E DBDC)
Ethernet: 4x 10/100/1000 (MT7530)
Button: 1x WPS, 1x Reset, 1x LED On/Off
LED: 7 LEDs (3x white, 2x red, 2x green)
MAC address assignment
======================
The MAC address assignment follows stock: The label MAC address is the LAN
MAC address, the WAN address is read from flash.
The WiFi MAC addresses are set in userspace to label MAC + 1 and label MAC
+ 2.
Installation (web interface)
============================
The device is cloud-managed, but there is a hidden local firmware upgrade
page in the OEM web interface. The device has to be registered in the
cloud in order to be able to access this page.
The system has a dual firmware design, there is no way to tell which
firmware is currently booted. Therefore, an -initramfs version is flashed
first.
1. Log into the OEM web GUI
2. Access the hidden upgrade page by navigating to
https://192.168.212.1/gui/#/main/debug/firmwareupgrade
3. Upload the -initramfs-kernel.bin file and flash it
4. Wait for OpenWrt to boot and log in via SSH
5. Transfer the sysupgrade file via SCP
6. Run sysupgrade to install the image
7. Reboot and enjoy
NB: If the initramfs version was installed in RAS2, the sysupgrade script
sets the boot number to the first partition. A backup has to be performed
manually in case the OEM firwmare should be kept.
Installation (UART method)
==========================
The UART method is more difficult, as the boot loader does not have a
timeout set. A semi-working stock firmware is required to configure it:
1. Attach UART
2. Boot the stock firmware until the message about failsafe mode appears
3. Enter failsafe mode by pressing "f" and "Enter"
4. Type "mount_root"
5. Run "fw_setenv bootmenu_delay 3"
6. Reboot, U-Boot now presents a menu
7. The -initramfs-kernel.bin image can be flashed using the menu
8. Run the regular sysupgrade for a permanent installation
Changing the partition to boot is a bit cumbersome in U-Boot, as there is
no menu to select it. It can only be checked using mstc_bootnum. To change
it, issue the following commands in U-Boot:
nand read 1800000 53c0000 800
mw.b 1800004 1 1
nand erase 53c0000 800
nand write 1800000 53c0000 800
This selects FW1. Replace "mw.b 1800004 1 1" by "mw.b 1800004 2 1" to
change to the second slot.
Back to stock
=============
It is possible to flash back to stock, but a OEM firmware upgrade is
required. ZyXEL does not provide the link on its website, but the link
can be acquired from the OEM web GUI by analyzing the transferred JSON
objects.
It is then a matter of writing the firmware to Kernel2 and setting the
boot partition to FW2:
mtd write zyxel.bin Kernel2
echo -ne "\x02" | dd of=/dev/mtdblock7 count=1 bs=1 seek=4 conv=notrunc
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Credits to forum users Annick and SirLouen for their initial work on this
device
- Correct WiFi MACs, they didn't match oem firmware
- Move nvmem-cells to bdinfo partition and remove &bdinfo reference
- Add OEM device model name R13 to SUPPORTED_DEVICES
This allows sysupgrading from Cudy's OpenWrt fork without force
- Label red_led and use it during failsafe mode and upgrades
MAC addresses as verified by OEM firmware:
use address source
LAN b4:4b:d6:2d:c8:4a label
WAN b4:4b:d6:2d:c8:4b label + 1
2g b4:4b:d6:2d:c8:4a label
5g b6:4b:d6:3d:c8:4a label + LA-Bit set + 4th oktet increased
The label MAC address is found in bdinfo 0xde00.
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
[read wifi mac from flash offset]
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.
Fixes: #11919
Signed-off-by: Haoan Li <lihaoan1001@163.com>
Hanyang Digitech Co., Ltd.
MSIP-CMM-HYD-HYC-G920
CJ-Hello HYC-G920
SoC : MediaTek MT7621AT
RAM : 256M (SK hynix H5TQ2G63FFR)
FLASH : 16MB (Winbond W25Q128BV)
WiFi : MediaTek MT7602EN bgn 2SS
WiFi : MediaTek MT7612EN nac 2SS
BTN : Reset
LED : - Power RED
- WAN Green
- LAN {1-4}
- WiFi 2.4 GHz Blue
- WiFi 5 GHz Blue
- USB Green
**For MT7621 stage1 DDR Test**
UART : J4 GND - 3V3 - TX - RX - GND / 57600-8N1
```
MT7621 stage1 code 10:33:55 (ASIC)
CPU=500000000 HZ BUS=166666666 HZ
```
**For u boot environment**
UART : J4 GND - 3V3 - TX - RX - GND / 115200-8N1
**UART Menu**
```
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
```
**Steps**
Press 4: Entr boot command line interface.
On the pormpt enter.
`setenv firmware_size 0xf60000`
Then enter.
`saveenv`
Then enter.
`reset`
**Device will reboot**
Set your IP 192.168.100.100/24
Connect your lan cable to wan port.
**On the UART Menu**
Press 2: Load system code then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) **enter** `Y`
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.100.55) ==:`192.168.100.55`
Input server IP (192.168.100.100) ==:`192.168.100.100`
Input Linux Kernel filename () ==:`openwrt-22.03.0-ramips-mt7621-hanyang_hyc-g920-squashfs-sysupgrade.bin`
After uploading firmware image, device will boot Openwrt.
Signed-off-by: Muhammad AL-Qadhy <m.ismael@gmail.com>
Hardware
========
- SoC: MediaTek MT7621AT (880MHz, Duel-Core)
- RAM: DDR3 128MB
- Flash: Winbond W25Q128JV (SPI-NOR 16MB)
- WiFi: MediaTek MT7915D (2.4GHz, 5GHz, DBDC)
- Ethernet: MediaTek MT7530 (WAN x1, LAN x3, SoC)
- UART: >TX RX GND 3v3 (115200 8N1, J1)
Do not connect 3v3. TX is marked with an arrow.
Installation
============
Flash factory image. This can be done using stock web ui.
Revert to stock firmware
========================
Flash stock firmware via OEM Web UI Recovery mode.
Web UI Recovery method
======================
1. Unplug the router
2. Plug in and hold reset button 5~10 secs
3. Set your computer IP address manually to 192.168.1.x / 255.255.255.0
4. Flash image with web browser to 192.168.1.1
Co-authored-by: Robert Senderek <robert.senderek@10g.pl>
Co-authored-by: Yoonji Park <koreapyj@dcmys.kr>
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit includes some additional changes:
- better handling of iv and keys in openssl/wolfssl variants
- fix compiler warnings and whitespace
- build all 3 variants as separate packages
- adjust the new package name in targets' DEVICE_PACKAGES
- remove PKG_FLAGS:=nonshared
[Beeline SmartBox Flash - OK]
Tested-by: Mikhail Zhilkin <csharper2005@gmail.com>
[after test: replaced a hardcoded IV size of 16 by cipher_info->iv_size]
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Hardware
--------
CPU: MediaTek MT7621 DAT
RAM: 128MB DDR3 (integrated)
FLASH: 16MB SPI-NOR ()
WiFi: MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax
SERIAL: 115200 8N1
LEDs - (3V3 - GND - RX - TX) - ETH ports
Installation
------------
Upload the factory image using the Web-UI.
Web-Recovery
------------
The router supports a HTTP recovery mode by holding the reset-button
when powering on. The interface is reachable at 192.168.0.1 and supports
installation using the factory image.
Signed-off-by: David Bauer <mail@david-bauer.net>
Specifications:
* SoC: MT7621AT
* RAM: 256MB (NT5CC64M16GP-DI)
* Flash: 16MB NOR SPI flash (GD25Q127CSIG, using GD25Q128C driver)
* WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC
* Ethernet: 4x1000M LAN, 1x 1000M WAN
* LEDs: Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue,
USB Blue
* Buttons: Reset,WPS, Wifi
* Serial interface: on board but not populated, pinout (from the DC jack
side to the WAN port side) is "3.3V Input Output Gnd". Baud rate is 57600,
settings are 8 data bits, no parity bit, one stop bit, and no flow control.
Stock flash layout:
```
GD25Q128C(c8 40180000) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K)
.numeraseregions = 0
Creating 7 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "Config2"
0x000000060000-0x000000fb0000 : "Kernel"
0x000000fb0000-0x000001000000 : "Private"
```
The kernel partition will be replaced with the OpenWrt image, the other
partitions are left untouched.
"Config2" seems to be the config storage used by the stock firmware.
"Private" is a 320kB empty JFFS2 partition that comes with the stock
firmware. One can get a larger space for OpenWrt by merging it with
"Kernel".
OpenWrt flash layout:
```
0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "u-boot-env"
0x000000040000-0x000000050000 : "factory"
0x000000050000-0x000000060000 : "config2_stock"
0x000000060000-0x000000fb0000 : "firmware"
0x000000fb0000-0x000001000000 : "private_stock"
```
The OpenWrt image must have 96 bytes of padding in the header.
MAC addresses on OEM firmware:
| | location on the flash | notes |
|------ |----------------------- |---------- |
| lan (eth2) | factory + 0xe000 | on label |
| wan (eth3) | factory + 0xe006 | |
| 2.4g (rax0) | not on flash | lan + 1 |
| 5g (ra0) | not on flash | lan + 2 |
Mac addresses of the 2.4g and 5g interface are stored as ASCII strings in
the u-boot-env partition, but they are not used. OpenWrt calculates
Wifi Mac addresses based on the LAN Mac.
Flash and test instructions:
Flash the encrypted image (available in the OpenWrt forum) through the
stock D-Dink web interface.
1. Open the case, and solder the 4-pin header near the WAN port.
2. Connect it to a USB-UART TTL (3.3V) adapter, no need to connect VCC.
3. Open a terminal emulator (e.g. `screen /dev/ttyUSB0` on linux) with
the settings mentioned above.
4. Setup a TFTP server on your PC that can serve
`xxx-ramips-mt7621-dlink_dir-853-a1-initramfs-kernel.bin`.
5. Connect any LAN port to your PC and set a static IPv4 address to
192.168.0.101 (netmask 255.255.255.0).
6. Power on the device and keeps pressing 1 until you see the prompt.
7. Use default IP addresses and enter the file name accordingly, then hit
enter.
8. Wait until it boots to OpenWrt, the default IP address is 192.168.1.1,
you need to change your PC network adapter to use DHCP in order to access
LUCI.
9. So far, the OpenWrt runs in RAM and the flash contents are not touched.
You can try OpenWrt without having to overwrite the stock firmware, a
reboot clears all changes.
10. Optionally, backup the stock firmware (the "firmware" partition) in
Luci.
11. To permantly install OpenWrt to the device , click
on "System -> Backup/Flash Firmware" in Luci and flash
`xxx-ramips-mt7621-dlink_dir-853-a1-squashfs-sysupgrade.bin`
Known problems:
* WLAN0 defaults to 5G after a fresh installation, to enable 2.4G network,
you need to config it manually in LUCI.
* If you see jffs2 related warnings/errors after updating from the stock
web interface, you need to do a reset in LUCI. The error will be gone after
a cold reboot.
Signed-off-by: Hang Zhou <929513338qq@gmail.com>
Sungbo Eo