mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2024-06-20 07:38:28 +02:00
ramips: add support for D-Link COVR-X1860 A1
The COVR-X1860 are MT7621-based AX1800 devices (similar to DAP-X1860, but with two Ethernet ports and external power supply) that are sold in sets of two (COVR-X1862) and three (COVR-X1863). Specification: - MT7621 - MT7915 + MT7975 2x2 802.11ax (DBDC) - 256MB RAM - 128 MB flash - 3 LEDs (red, orange, white), routed to one indicator in the top of the device - 2 buttons (WPS in the back and Reset at the bottom of the device) MAC addresses: - LAN MAC (printed on the device) is stored in config2 partition as ASCII (entry factory_mac=xx:xx:xx:xx:xx:xx) - WAN MAC: LAN MAC + 3 - 2.4G MAC: LAN MAC + 1 - 5G MAC: LAN MAC + 2 The pins for the serial console are already labeled on the board (VCC, TX, RX, GND). Serial settings: 3.3V, 115200,8n1 Flashing via OEM Web Interface: - Download openwrt-ramips-mt7621-dlink_covr-x1860-a1-squashfs-factory.bin via the OEM web interface firmware update - The configuration wizard can be skipped by directly going to http://192.168.0.1/UpdateFirmware_Simple.html Flashing via Recovery Web Interface: - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0 - Press the reset button while powering on the deivce - Keep the reset button pressed until the status LED blinks red - Open a Chromium based browser and goto http://192.168.0.1 - Download openwrt-ramips-mt7621-dlink_covr-x1860-a1-squashfs-recovery.bin Revert back to stock using the Recovery Web Interface: - Set your IP address to 192.168.0.10, subnetmask 255.255.255.25 - Press the reset button while powering on the deivce - Keep the reset button pressed until the status LED blinks red - Open a Chromium based browser and goto http://192.168.0.1 - Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below. Decrypting a D-Link firmware image: - Download https://github.com/openwrt/firmware-utils/blob/master/src/dlink-sge-image.c and https://raw.githubusercontent.com/openwrt/firmware-utils/master/src/dlink-sge-image.h - Compile a binary from the downloaded file, e.g. gcc dlink-sge-image.c -lcrypto -o dlink-sge-image - Run ./dlink-sge-image COVR-X1860 <OriginalFirmware> <OutputFile> -d - Example for firmware 102b01: ./dlink-sge-image COVR-X1860 COVR-X1860_RevA_Firmware_102b01.bin COVR-X1860_RevA_Firmware_102b01_Decrypted.bin -d The pull request is based on the discussion in https://forum.openwrt.org/t/add-support-for-d-link-covr-x1860 Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
This commit is contained in:
Roland Reinl
Hauke Mehrtens
parent
684d1a5c35
commit
0a18259e4a
186
target/linux/ramips/dts/mt7621_dlink_covr-x1860-a1.dts
Normal file
186
target/linux/ramips/dts/mt7621_dlink_covr-x1860-a1.dts
Normal file
|
|
@ -0,0 +1,186 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "mt7621.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
compatible = "dlink,covr-x1860-a1", "mediatek,mt7621-soc";
|
||||
model = "D-Link COVR-X1860 A1";
|
||||
|
||||
aliases {
|
||||
led-boot = &status_orange;
|
||||
led-failsafe = &status_red;
|
||||
led-running = &status_white;
|
||||
led-upgrade = &status_red;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
status_white: power {
|
||||
label = "white:status";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
status_orange: status_orange {
|
||||
label = "orange:status";
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
status_red: status_red {
|
||||
label = "red:status";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
virtual_flash {
|
||||
compatible = "mtd-concat";
|
||||
|
||||
devices = <&fwconcat0 &fwconcat1>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "ubi";
|
||||
reg = <0x0 0x0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nand {
|
||||
status = "okay";
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "bootloader";
|
||||
reg = <0x0 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
label = "config";
|
||||
reg = <0x80000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
factory: partition@100000 {
|
||||
label = "factory";
|
||||
reg = <0x100000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
label = "config2";
|
||||
reg = <0x180000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1c0000 {
|
||||
label = "kernel";
|
||||
reg = <0x1c0000 0x800000>;
|
||||
};
|
||||
|
||||
fwconcat0: partition@9c0000 {
|
||||
label = "fwconcat0";
|
||||
reg = <0x9c0000 0x2000000>;
|
||||
};
|
||||
|
||||
partition@29c0000 {
|
||||
label = "kernel2";
|
||||
reg = <0x29c0000 0x800000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
fwconcat1: partition@31c0000 {
|
||||
label = "fwconcat1";
|
||||
reg = <0x31c0000 0x2a00000>;
|
||||
};
|
||||
|
||||
partition@5bc0000 {
|
||||
label = "private";
|
||||
reg = <0x5bc0000 0x1400000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@6fc0000 {
|
||||
label = "mydlink";
|
||||
reg = <0x6fc0000 0x600000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@75c0000 {
|
||||
label = "myconfig";
|
||||
reg = <0x75c0000 0xa00000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
wifi@0,0 {
|
||||
compatible = "mediatek,mt76";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
mediatek,mtd-eeprom = <&factory 0x0>;
|
||||
mediatek,disable-radar-background;
|
||||
};
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
status = "okay";
|
||||
phy-handle = <ðphy4>;
|
||||
};
|
||||
|
||||
&mdio {
|
||||
ethphy4: ethernet-phy@4 {
|
||||
reg = <4>;
|
||||
};
|
||||
};
|
||||
|
||||
&switch0 {
|
||||
ports {
|
||||
port@0 {
|
||||
status = "okay";
|
||||
label = "internet";
|
||||
};
|
||||
|
||||
port@2 {
|
||||
status = "okay";
|
||||
label = "ethernet";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
|
@ -9,6 +9,14 @@ DEFAULT_SOC := mt7621
|
|||
|
||||
DEVICE_VARS += ELECOM_HWNAME LINKSYS_HWNAME DLINK_HWID
|
||||
|
||||
define Build/append-dlink-covr-metadata
|
||||
echo -ne '{"supported_devices": "$(1)", "firmware": "' > $@metadata.tmp
|
||||
$(MKHASH) md5 "$@" | head -c32 >> $@metadata.tmp
|
||||
echo '"}' >> $@metadata.tmp
|
||||
fwtool -I $@metadata.tmp $@
|
||||
rm $@metadata.tmp
|
||||
endef
|
||||
|
||||
define Build/arcadyan-trx
|
||||
echo -ne "hsqs" > $@.hsqs
|
||||
$(eval trx_magic=$(word 1,$(1)))
|
||||
|
|
@ -641,6 +649,31 @@ define Device/cudy_x6-v2
|
|||
endef
|
||||
TARGET_DEVICES += cudy_x6-v2
|
||||
|
||||
define Device/dlink_covr-x1860-a1
|
||||
$(Device/dsa-migration)
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
KERNEL_SIZE := 8192k
|
||||
IMAGE_SIZE := 40960k
|
||||
DEVICE_VENDOR := D-Link
|
||||
DEVICE_MODEL := COVR-X1860
|
||||
DEVICE_VARIANT := A1
|
||||
DEVICE_PACKAGES := kmod-mt7915-firmware
|
||||
UBINIZE_OPTS := -E 5
|
||||
KERNEL_LOADADDR := 0x82000000
|
||||
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
||||
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | \
|
||||
append-squashfs4-fakeroot
|
||||
IMAGES += factory.bin recovery.bin
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
IMAGE/recovery.bin := append-kernel | pad-to $$(KERNEL_SIZE) | \
|
||||
append-ubi | check-size
|
||||
IMAGE/factory.bin := $$(IMAGE/recovery.bin) | \
|
||||
append-dlink-covr-metadata $$(DEVICE_MODEL) | \
|
||||
dlink-sge-image $$(DEVICE_MODEL)
|
||||
endef
|
||||
TARGET_DEVICES += dlink_covr-x1860-a1
|
||||
|
||||
define Device/dlink_dxx-1xx0-x1
|
||||
DEVICE_VENDOR := D-Link
|
||||
DEVICE_PACKAGES := kmod-mt7615-firmware rssileds
|
||||
|
|
|
|||
|
|
@ -98,6 +98,9 @@ ramips_setup_interfaces()
|
|||
zyxel,nr7101)
|
||||
ucidef_set_interfaces_lan_wan "lan" "wan"
|
||||
;;
|
||||
dlink,covr-x1860-a1)
|
||||
ucidef_set_interfaces_lan_wan "ethernet" "internet"
|
||||
;;
|
||||
gnubee,gb-pc1)
|
||||
ucidef_set_interface_lan "ethblack ethblue"
|
||||
;;
|
||||
|
|
@ -219,6 +222,11 @@ ramips_setup_macs()
|
|||
label_mac=$lan_mac
|
||||
wan_mac=$(macaddr_add "$lan_mac" 1)
|
||||
;;
|
||||
dlink,covr-x1860-a1)
|
||||
label_mac=$(mtd_get_mac_ascii config2 factory_mac)
|
||||
wan_mac=$(macaddr_add "$label_mac" 3)
|
||||
lan_mac=$label_mac
|
||||
;;
|
||||
dlink,dir-860l-b1)
|
||||
lan_mac=$(mtd_get_mac_ascii factory lanmac)
|
||||
wan_mac=$(mtd_get_mac_ascii factory wanmac)
|
||||
|
|
|
|||
|
|
@ -46,6 +46,13 @@ case "$board" in
|
|||
[ "$PHYNBR" = "1" ] && \
|
||||
macaddr_add $lan_mac_addr 2 > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
dlink,covr-x1860-a1)
|
||||
label_mac=$(mtd_get_mac_ascii config2 factory_mac)
|
||||
[ "$PHYNBR" = "0" ] && \
|
||||
macaddr_add $label_mac 1 > /sys${DEVPATH}/macaddress
|
||||
[ "$PHYNBR" = "1" ] && \
|
||||
macaddr_add $label_mac 2 > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
dlink,dap-x1860-a1)
|
||||
hw_mac_addr="$(mtd_get_mac_binary factory 0x4)"
|
||||
[ "$PHYNBR" = "0" ] && \
|
||||
|
|
|
|||
|
|
@ -63,6 +63,7 @@ platform_do_upgrade() {
|
|||
beeline,smartbox-turbo|\
|
||||
beeline,smartbox-turbo-plus|\
|
||||
belkin,rt1800|\
|
||||
dlink,covr-x1860-a1|\
|
||||
dlink,dap-x1860-a1|\
|
||||
dlink,dir-1960-a1|\
|
||||
dlink,dir-2640-a1|\
|
||||
|
|
|
|||
Loading…
Reference in New Issue
Block a user