Add 6.1 tag to upstream patch now that 6.1 got tagged. This permits to
track patch in a better way and directly drop them on kernel bump.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
(cherry picked from commit 802ca492d8)
This patch is needed to handle interrupts by the second VPE on the Lantiq
ARX100, xRX200, xRX300 and xRX330 SoCs. Switching some ICU interrupts to
the second VPE results in a hang. Currently, the vsmp_init_secondary()
function is responsible for enabling these interrupts. It only enables
Malta-specific interrupts (SW0, SW1, HW4 and HW5).
The MIPS core has 8 interrupts defined. On Lantiq SoCs, hardware
interrupts are wired to an ICU instance. Each VPE has an independent
instance of the ICU. The mapping of the ICU interrupts is shown below:
SW0(IP0) - IPI call,
SW1(IP1) - IPI resched,
HW0(IP2) - ICU 0-31,
HW1(IP3) - ICU 32-63,
HW2(IP4) - ICU 64-95,
HW3(IP5) - ICU 96-127,
HW4(IP6) - ICU 128-159,
HW5(IP7) - timer.
This patch enables all interrupt lines on the second VPE.
This problem affects multithreaded SoCs with a custom interrupt controller.
SOCs with 1004Kc core and newer use the MIPS GIC. At this point, I am aware
that the Realtek RTL839x and RTL930x SoCs may need a similar fix. In the
future, this may be replaced with some generic solution.
Tested on Lantiq xRX200.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
(cherry picked from commit fbd33d6164)
All buttons of the FritzBox 7360 family are active-low, not active-high.
Corrent the GPIO flag. This fixes release triggers upon push of a button.
Reported-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3154537864)
Removed upstreamed:
target/linux/mvebu/patches-5.4/001-PCI-aardvark-Wait-for-endpoint-to-be-ready-before-tr.patch
target/linux/mvebu/patches-5.4/016-PCI-aardvark-Train-link-immediately-after-enabling-t.patch
target/linux/mvebu/patches-5.4/017-PCI-aardvark-Improve-link-training.patch
target/linux/mvebu/patches-5.4/018-PCI-aardvark-Issue-PERST-via-GPIO.patch
target/linux/mvebu/patches-5.4/020-arm64-dts-marvell-armada-37xx-Set-pcie_reset_pin-to-.patch
The following patch does not apply to upstream any more and needs some
more work to make it work fully again. I am not sure if we are still
able to set the UART to a none standard baud rate.
target/linux/ath79/patches-5.4/921-serial-core-add-support-for-boot-console-with-arbitr.patch
These patches needed manually changes:
target/linux/generic/pending-5.4/110-ehci_hcd_ignore_oc.patch
target/linux/ipq806x/patches-5.4/0065-arm-override-compiler-flags.patch
target/linux/layerscape/patches-5.4/804-crypto-0016-MLKU-114-1-crypto-caam-reduce-page-0-regs-access-to-.patch
target/linux/mvebu/patches-5.4/019-PCI-aardvark-Add-PHY-support.patch
target/linux/octeontx/patches-5.4/0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch
All others updated automatically.
Compile-tested on: malta/le, armvirt/64, lantiq/xrx200
Runtime-tested on: malta/le, armvirt/64, lantiq/xrx200
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The board has a fixed size kernel partition but do not limit the kernel
size during image building.
Disable image building for both boards as well, since the kernel of the
last release as well as master are to big to fit into the 2 MByte kernel
partition.
Signed-off-by: Mathias Kresin <dev@kresin.me>
When the ltq_deu_vr9 kernel module is loaded, hostapd does not start any
more. It fails with this error message:
daemon.err hostapd: nl80211: kernel reports: key addition failed
daemon.err hostapd: Interface initialization failed
OpenWrt uses the standard Linux crypto API in the wifi drivers now
and this probably makes the system offload more crypto operations to
special hardware like the Lantiq DEU. There is probably a bug in the DEU
and these operations fail and then hostapd does not start the interface.
Do not include the Lantiq DEU by default any more.
Fixes: FS#3901
Fixes: 53b6783907 ("mac80211: remove patches stripping down crypto support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Notupus <notpp46@gmail.com>
(cherry-picked from commit 964863bb23)
CONFIG_FORTIFY_SOURCE=y is already set in the generic kernel
configuration, but it is not working for MIPS on kernel 5.4, support for
MIPS was only added with kernel 5.5, other architectures like aarch64
support FORTIFY_SOURCE already since some time.
This patch adds support for FORTIFY_SOURCE to MIPS with kernel 5.4,
kernel 5.10 already supports this and needs no changes.
This backports one patch from kernel 5.5 and one fix from 5.8 to make
fortify source also work on our kernel 5.4.
The changes are not compatible with the
306-mips_mem_functions_performance.patch patch which was also removed
with kernel 5.10, probably because of the same problems. I think it is
not needed anyway as the compiler should automatically optimize the
calls to memset(), memcpy() and memmove() even when not explicitly
telling the compiler to use the build in variant.
This increases the size of an uncompressed kernel by less than 1 KB.
Acked-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 9ffa2f8193)
Removed because in upstream*
mvebu/patches-5.4/319-ARM-dts-turris-omnia-configure-LED-2--INTn-pin-as-interrupt-pin.patch
Manually rebased*
generic/backport-5.4/700-v5.5-net-core-allow-fast-GRO-for-skbs-with-Ethernet-heade.patch
Added new backport*
generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
All others updated automatically.
The new backport was included based on this[1] upstream commit that will be
mainlined soon. This change is needed because Eric Dumazet's check for
NET_IP_ALIGN (landed in 5.4.114) causes huge slowdowns on drivers which use
napi_gro_frags().
Compile-tested on: x86/64, armvirt/64, ath79/generic
Runtime-tested on: x86/64, armvirt/64, ath79/generic
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rather than using the clunky, old, slower wireguard-linux-compat out of
tree module, this commit does a patch-by-patch backport of upstream's
wireguard to 5.4. This specific backport is in widespread use, being
part of SUSE's enterprise kernel, Oracle's enterprise kernel, Google's
Android kernel, Gentoo's distro kernel, and probably more I've forgotten
about. It's definately the "more proper" way of adding wireguard to a
kernel than the ugly compat.h hell of the wireguard-linux-compat repo.
And most importantly for OpenWRT, it allows using the same module
configuration code for 5.10 as for 5.4, with no need for bifurcation.
These patches are from the backport tree which is maintained in the
open here: https://git.zx2c4.com/wireguard-linux/log/?h=backport-5.4.y
I'll be sending PRs to update this as needed.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
(cherry picked from commit 3888fa7880)
(cherry picked from commit d540725871)
(cherry picked from commit 196f3d586f)
(cherry picked from commit 3500fd7938)
(cherry picked from commit 23b801d3ba)
(cherry picked from commit 0c0cb97da7)
(cherry picked from commit 2a27f6f90a)
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
1. Use upstream accepted NVMEM patches
2. Minor fix for BCM4908 partitioning
3. Support for Linksys firmware partitions on Northstar
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 3fd0a4222b)
Some users report that current snapshot producies non-bootable images.
Stock uboot can boot images if the kernel is smaller than 2MB.
Set maximum kernel size and disable image building for this board.
Ref: https://forum.openwrt.org/t/astoria-arv7519rw22-bootloops-after-upgrade/89843
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
(cherry picked from commit c027dbac5a)
It's meant to provide upstream support for mtd & NVMEM. It's required
e.g. for reading MAC address from mtd partition content. It seems to be
in a final shape so it's worth testing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit e90e75b12c)
This adds the latest version of ofpart commit. It hopefully
1. Doesn't break compilation
2. Doesn't break partitioning
(this time).
It's required to implement fixed partitioning with some quirks. It's
required by bcm53xx, bcm4908, kirkwood, lantiq and mvebu.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 7a7b2fd809)
These boards have a fixed size kernel partition but do not limit the
kernel size during image building.
Disable image building for both boards as well, since the kernel of the
last release as well as master are to big to fit into the 2 MByte kernel
partition.
Signed-off-by: Mathias Kresin <dev@kresin.me>
(cherry picked from commit 23dd786734)
The USB ports if a FRIZZ!Box 7320 do not supply power to connected
devices.
Add the GPIOs enabling USB power as regulator, to enable USB power
supply as soon as the USB driver is loaded.
Fixes FS#3624
Signed-off-by: Mathias Kresin <dev@kresin.me>
(cherry picked from commit 6e4e97b2256327bb380ee2a83da9a1ddf657e395)
FRITZ!Box 7412 loads the firmware for fast ethernet PHY and mii is
more accurate in this case.
Gmii is used by Gigabit ethernet PHYs.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Reviewed-by: Mathias Kresin <dev@kresin.me>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This drops the shebang from another bunch of files in various /lib
folders, as these are sourced and the shebang is useless.
Fix execute bit in one case, too.
This should cover almost all trivial cases now, i.e. where /lib is
actually used for library files.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:
device/image name: vendor_model
compatible: vendor,model
The equal redundant definitions are a symptom of this process.
Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.
This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The following four led triggers are enabled in generic config.
* kmod-ledtrig-default-on
* kmod-ledtrig-heartbeat
* kmod-ledtrig-netdev
* kmod-ledtrig-timer
Drop the packages and remove them from DEVICE_PACKAGES.
There's no other package depending on them in this repo.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Those targets have already enabled some other LED triggers, so enabling
a few more won't be a big problem.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The heartbeat trigger is used by luci-mod-system, which is installed
as a part of the standard luci package set. It seems the LED trigger
will be required quite often, so let's enable it by default.
This increases uncompressed kernel size by about 100 bytes on ath79/generic.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
These parameters are the same as in vr9.dtsi. This patch removes
redundant parameters.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
The sub target does not support network and there are not so many users
out there, just mark it as source only, so we do jot have to build it.
The quality is not worse than before, it just does not make much sense
to build this automatically.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes build of squashfs image on lantiq. Currently the FEATURE
variable is overwritten by the subtarget.
Fixes: FS#3480
Fixes: f1c6523376 ("lantiq: clean up target/subtarget features")
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[reformat Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The feature "squashfs" is defined for target and all subtargets
individually. Remove the redundant entries in the subtargets.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[split patch, adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware:
- SoC: Lantiq VRX 220
- CPU: 2x MIPS 34Kc 500 MHz
- RAM: 128 MiB 250 MHz
- Flash: 128 MiB NAND
- Ethernet: Built-in Fast Ethernet switch, 4 ports used
- Wifi: Atheros AR9381-AL1A b/g/n with 2 pcb/internal and 1 external antennas
- USB: 1x USB 2.0
- DSL: Built-in A/VDSL2 modem
- DECT: Dialog SC14441
- LEDs: 1 two-color, 4 one-color
- Buttons: 1x DECT, 1x WIFI
- Telephone connectors: 1 FXS port via TAE or RJ11 connector
With the exception of FXS/DECT everything works
(there are no drivers for AVM's FXS or DECT implementation),
DSL is yet untested.
Installation:
Boot up the device and wait a few seconds. Run the eva_ramboot.py script
in scripts/flashing/ to load the initramfs image on the device:
$ ./scripts/flashing/eva_ramboot.py 192.168.178.1 <path to your initramfs image>
If the script fails to reach the device, maybe try 169.254.120.1.
Wait until booting is complete. You should now be able to reach your device
under the default ip address 192.168.1.1.
Before flashing, check if linux_fs_start is not set to 1 in the tffs partition:
$ fritz_tffs_nand -d /dev/mtd1 -n linux_fs_start
If linux_fs_start is 1, you will need to reset it to 0, either by FTP,
upgrading FritzOS or doing a recovery.
Now you should be able to flash the device using sysupgrade.
Signed-off-by: Leon Maurice Adam <leon.adam@aol.de>
Acked-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[drop BOARD_NAME, use wpad-basic-wolfssl, drop 4.19, drop dts-v1,
remove model prefix from LED names]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The target uses 5.4 as default kernel since 06/2020.
Kernel 4.19 support is not really maintained anymore, it does not
seem to be needed and upcoming changes (mainly DSA) will break
backward-compatibility anyway.
Thus, make maintaining of old stuff and reviewing of new stuff
easier by removing support for kernel 4.19.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like in the previous patches for other targets, this will remove
the "devicename" from LED labels in lantiq.
The devicename is removed in DTS files and 01_leds, consolidation
of definitions into DTSI files is done where (easily) possible,
and migration scripts are updated. The DTS/DTSI consolidation is
only performed for files-5.4.
For lantiq,easy98020 some LED definitions have the form
"devicename:function" without the color, so we need to implement
explicit migration for that one.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Seemingly unneeded based on new upstream code so manually deleted:
layerscape:
820-usb-0007-usb-dwc3-gadget-increase-timeout-value-for-send-ep-c.patch
Manually merged:
generic-hack:
251-sound_kconfig.patch
All other modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800, lantiq/Easybox 904 xDSL
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[add lantiq test report, minor commit message clarification]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.
In lantiq, we therefore requested to have in the DTS files so far,
and omit it in the DTSI files. However, essentially the syntax of
the parent SoC-based DTSI files already determines the DTS
version, so putting it into the DTS files is just a useless repetition.
Consequently, this patch puts the dts-v1 statement into the top-level
SoC-based DTSI files, and removes all other occurences.
Since the dts-v1 statement needs to be before any other definitions,
this also moves the includes accordingly where necessary.
Changes are applied to files-5.4 only, files-4.19 remains untouched.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x, lantiq/xrx200 and ath79/generic
Run-tested: ipq806x (R7800), lantiq (Easybox 904 xDSL)
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[add test on lantiq]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is the most popular choice in the linux kernel tree.
Within OpenWrt, this change will establish consistency with ath79
and ramips targets.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[extend commit message, include netgear_dm200, update base-files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As described in commit commit 891a700759 ("lantiq: enable second VPE
on Fritz!Box 7412"):
The AVM Fritz!Box 7412 does not use the VMMC part of the Lantiq chip but
rather a proprietary solution based on the DECT chip for the FXS ports.
We can remove last traces of vmmc in dts.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
In order to support SAE/WPA3-Personal in default images. Replace almost
all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for
consistency. Keep out ar71xx from the list as it won't be in the next
release and would only make backports harder.
Build-tested (build-bot settings):
ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway,
sunxi: a53
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hauke Mehrtens
Adrian Schmutzler