openwrt/target/linux/ramips/dts/WZR-AGL300NH.dts

149 lines
2.4 KiB
Plaintext

/dts-v1/;
#include "rt2880.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
#address-cells = <1>;
#size-cells = <1>;
compatible = "buffalo,wzr-agl300nh", "ralink,rt2880-soc";
model = "Buffalo WZR-AGL300NH";
aliases {
led-boot = &led_router;
led-failsafe = &led_router;
led-running = &led_router;
led-upgrade = &led_router;
};
cfi@1f000000 {
compatible = "cfi-flash";
reg = <0x1f000000 0x800000>;
bank-width = <2>;
device-width = <2>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "uboot";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "uboot-env";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x10000>;
read-only;
};
partition@50000 {
label = "firmware";
reg = <0x50000 0x3b0000>;
};
};
};
rtl8366s {
compatible = "realtek,rtl8366s";
gpio-sda = <&gpio0 1 GPIO_ACTIVE_HIGH>;
gpio-sck = <&gpio0 2 GPIO_ACTIVE_HIGH>;
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
poll-interval = <100>;
wps {
label = "wps";
gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
router {
label = "router_switch";
gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
linux,code = <BTN_0>;
};
reset {
label = "reset";
gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
gpio-leds {
compatible = "gpio-leds";
led_router: router {
label = "wzr-agl300nh:green:router";
gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
};
diag {
label = "wzr-agl300nh:red:diag";
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
};
security_g {
label = "wzr-agl300nh:orange:security_g";
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
};
security_n {
label = "wzr-agl300nh:orange:security_n";
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
};
};
};
&gpio0 {
status = "okay";
};
&pinctrl {
state_default: pinctrl0 {
gpio {
ralink,group = "i2c", "uartlite", "mdio";
ralink,function = "gpio";
};
};
};
&ethernet {
status = "okay";
mtd-mac-address = <&factory 0x4>;
port@0 {
mediatek,fixed-link = <1000 1 1 1>;
};
mdio-bus {
status = "okay";
phy0: ethernet-phy@0 {
phy-mode = "mii";
reg = <0>;
};
};
};
&pci {
status = "okay";
};
&wmac {
ralink,mtd-eeprom = <&factory 0>;
};