Pci is broken when bootm is used instead of the custom bootipq. This
is caused by the lack of reset by the bootloader. Make the driver do
the reset to fix this specific problem.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The target uses 5.4 as default kernel since 04/2020.
Kernel 4.19 support is not really maintained anymore, and there has
been a lot of changes between 4.19 and 5.4 on this target. Despite,
new devices are typically added for 5.4 only anyway.
Thus, make maintaining of old stuff and reviewing of new stuff
easier by removing support for kernel 4.19.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The target uses 5.4 as default kernel since 03/2020.
Kernel 4.19 support is not really maintained anymore, it does not
seem to be needed, and removing it will make upcoming driver
updates easier. Thus, remove it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* add d-link_dgs-1210-10p support
* make sure mips16 is disabled
* add a generic sub target
* add proper cflags
Signed-off-by: John Crispin <john@phrozen.org>
The board was renamed without changing the BUILD_DEVICES in the U-Boot
Makefile, this broken the build.
Fixes: 0830ae3a2f ("sunxi: Correct manufacturer name to Sinovoip")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
- CPU: Allwinner H3, Quad-core Cortex-A7 Up to 1.2GHz
- DDR3 RAM: 512MB/1GB
- Network:
10/100/1000M Ethernet x 1，
10/100M Ethernet x 1
- WiFi: 802.11b/g/n, with SMA antenna interface
- USB Host: Type-A x2
- MicroSD Slot x 1
- MicroUSB: for OTG and power input
- Debug Serial Port: 3Pin 2.54mm pitch pin-header
- LED:
nanopi:red:status
nanopi:green:wan
nanopi:green:lan
- KEY:
reset
- Power Supply: DC 5V/2A
Installation:
- Write the image to SD Card with dd
- Boot NanoPi from the SD Card
Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
E1700AC v2 based on Qualcomm/Atheros QCA9563 + QCA9880.
Specification:
- 750/400/250 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 2 x 10/1000M Mbps Ethernet (RJ45)
- 1 x MiniPCI-e
- 1 x SIM (3G/4G)
- 1 x USB 2.0 Port
- 5 x LED , 2 x Button(S8-Reset Buttun), 1 x power input
- UART (J5) header on PCB (115200 8N1)
Flash instruction:
1.Using tftp mode with UART connection and original LEDE image
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
to "firmware.bin" and place it in tftp server directory.
- Connect PC with one of LAN ports, power up the router and press
key "Enter" to access U-Boot CLI.
- Use the following commands to update the device to LEDE:
run lfw
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
2.Using httpd mode with Web UI connection and original LEDE image
- Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
- Connect PC with one of LAN ports,press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
leds flashing.
- Open your browser and enter 192.168.1.1,You will see the upgrade
interface, select "openwrt-ar71xx-generic-xxx-squashfs-
sysupgrade.bin" and click the upgrade button.
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[cut out of bigger patch, keep swconfig, whitespace fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9558)
- 3x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 4x miniPCIe slot (USB 2.0 bus only)
- 1x microSIM slot
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x 3-pos switch
- 1x DC jack for main power input (9-48 V)
- UART (JP5) and LEDs (J8) headers on PCB
Flash instruction:
1.Using tftp mode with UART connection and original LEDE image
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
to "firmware.bin" and place it in tftp server directory.
- Connect PC with one of LAN ports, power up the router and press
key "Enter" to access U-Boot CLI.
- Use the following commands to update the device to LEDE:
run lfw
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
2.Using httpd mode with Web UI connection and original LEDE image
- Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
- Connect PC with one of LAN ports,press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
leds flashing.
- Open your browser and enter 192.168.1.1,You will see the upgrade
interface, select "openwrt-ar71xx-generic-xxx-squashfs-
sysupgrade.bin" and click the upgrade button.
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[cut out of bigger patch, keep swconfig, whitespace adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Qxwlan E750G v8 is based on Qualcomm QCA9344 + QCA9334.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4G GHz (AR9344)
- 2x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction:
1.Using tftp mode with UART connection and original LEDE image
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
to "firmware.bin" and place it in tftp server directory.
- Connect PC with one of LAN ports, power up the router and press
key "Enter" to access U-Boot CLI.
- Use the following commands to update the device to LEDE:
run lfw
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
2.Using httpd mode with Web UI connection and original LEDE image
- Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
- Connect PC with one of LAN ports,press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
leds flashing.
- Open your browser and enter 192.168.1.1,You will see the upgrade
interface, select "openwrt-ar71xx-generic-xxx-squashfs-
sysupgrade.bin" and click the upgrade button.
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[cut out of bigger patch, keep swconfig]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
After the status rework, ieee80211_tx_status_ext is leaking un-acknowledged
packets for stations in powersave mode.
To fix this, move the code handling those packets from __ieee80211_tx_status
into ieee80211_tx_status_ext
Reported-by: Tobias Waldvogel <tobias.waldvogel@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reverts commit ef7c34c1d1.
The commit seems to break all buildbots with messages like:
/builder/shared-workdir/build/include/toplevel.mk:15:
/builder/shared-workdir/build/include/toplevel-vars.mk: No such file or directory
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
version_abbrev uses $(shell) and the ?= is causing make to run the command
over and over again, causing a significant build slowdown
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The code is now much cleaner and works better than the old code.
Preparation for submitting it upstream (though with a different API)
Also add back MT7621 support and fix flow table coherence issues on
MT7622
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to make it easier for users to build with SELinux, have a
single option in 'Global build settings' to enable all necessary
kernel features, userland packages and build-system hooks.
Also add better descriptions and help messages while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
8e0f29a mount: remove support for legacy overlayfs before v2.3
0f8a443 mount: fix log format string and indentation
46a56d3 overlay: use precompiler macros for reoccuring path names
f25ab8a mount: apply SELinux labels before overlayfs mount
Total ipk size change (ipq40xx): +120b
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of duplicating the '/sbin/setfiles' binary, have
'/sbin/restorecon' as yet another alias for
'/sbin/policycoreutils-setfiles'.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Expose WPS ubus API only if compiled with WPS support and add new
handler for wps_status call.
Also add '-v wps' option to check whether WPS support is present in
hostapd.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Qxwlan E750A v4 is based on Qualcomm QCA9344.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 5G GHz (AR9344)
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (USB 2.0 bus only)
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction:
1.Using tftp mode with UART connection and original LEDE image
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
to "firmware.bin" and place it in tftp server directory.
- Connect PC with one of LAN ports, power up the router and press
key "Enter" to access U-Boot CLI.
- Use the following commands to update the device to LEDE:
run lfw
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
2.Using httpd mode with Web UI connection and original LEDE image
- Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
- Connect PC with one of LAN ports,press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
leds flashing.
- Open your browser and enter 192.168.1.1,You will see the upgrade
interface, select "openwrt-ar71xx-generic-xxx-squashfs-
sysupgrade.bin" and click the upgrade button.
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
Signed-off-by: Peng Zhang <sd20@qxwlan.com>
[cut out of bigger patch, alter use of DEVICE_VARIANT, merge case
in 01_leds, use lower case for v4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like in the previous patches for various targets, this removes
the "devicename" from LED labels in rtl838x, as it's useless and
only creates complexity.
Since the target is fresh and so far only system LEDs were added,
this does not add a migration script.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The syntax of the shared SoC DTSI file determines the DTS version,
so no need to repeat the "/dts-v1/;" identifier in every file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The idea of commit a14f5bb4bd was to use wpad-basic-wolfssl
consistently throughout the whole trunk, so use it here as well.
Fixes: 50fdddae05 ("BPi-M2U kernel modules for onboard WiFi")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fix wrong magic number verification for FW files.
Correct handling of external RTL8218B firmware PHY name in firmware.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
build: always build package/kernel/linux
If no in-tree module packages are selected, the build system does not process
package/kernel/linux. This package is required for building the virtual
'kernel' package, which is specified as a dependency for all kernel packages.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The router profile installs many packages unnecessary for
the operation of a typical ethernet switch. Instead of creating
an empty switch profile upfront, use the basic profile until
a set of common packages crystallizes.
Signed-off-by: Andreas Oberritter <obi@saftware.de>
Fixes long delay on boot when booting from flash. The driver waits
for one minute for userspace to load firmware, before it becomes
available.
Signed-off-by: Andreas Oberritter <obi@saftware.de>
This adds basic support for reading the internal PHYs of the RTL839x SoCs
and full support for the 2 PHYs connected to the 1000Base-X SerDes of
the RTL8393 SoC.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This adds correct interrupt routing settings for IRQs on the RTL839x SoCs.
It also speeds up irq handling based on work by biot for all SoCs.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
The vDSO is used to accelerate some syscalls. It should work fine wherever it's
available, so enable it globally for all targets.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Specification
CPU: Allwinner H3, Quad-core Cortex-A7 Up to 1.2GHz
DDR3 RAM: 256MB/512MB
Connectivity: 10/100/1000Mbps Ethernet
USB Host: Type-A x 1
MicroSD Slot x 1
MicroUSB: for power input only
Debug Serial Port: 4Pin, 2.54 mm pitch pin header
Power Supply: DC 5V/2A
PCB Dimension: 40 x 40 x 1.2mm
Installation:
Burn the image file to an SD Card with dd or any image burning tool
Boot ZeroPi from the SD Card
The following features are working and tested:
Ethernet port 10/100/1000M Ethernet
Remarks: SBC is mostly compatible and boots with FriendlyARM NanoPI M1 plus DTS also (zeropi has no working hdmi)
Signed-off-by: Arturas Moskvinas <arturas.moskvinas@gmail.com>
Tested on a A20 board:
$ cat /proc/asound/cards
0 [SPDIF ]: On-board_SPDIF - On-board SPDIF
On-board SPDIF
Size of the module for a 32bit kernel:
60708 linux-5.4.66/sound/soc/sunxi/sun4i-spdif.ko
Signed-off-by: Andre Heider <a.heider@gmail.com>
Size of the modules for a Cortex A7 build:
43920 linux-5.4.66/sound/soc/codecs/snd-soc-spdif-rx.ko
44044 linux-5.4.66/sound/soc/codecs/snd-soc-spdif-tx.ko
Signed-off-by: Andre Heider <a.heider@gmail.com>
Mainline u-boot dynamically passes the mtd partitions via devicetree:
$ cat /proc/mtd
dev: size erasesize name
mtd0: 003f0000 00001000 "firmware"
mtd1: 00010000 00001000 "u-boot-env"
Add support for this setup.
Signed-off-by: Andre Heider <a.heider@gmail.com>
The generic bootscript is tailored around a downstream firmware and
doesn't work on a firmware built from mainline components.
Add a bootscript which:
* sets $console since mainline u-boot doesn't do that
* uses distro boot variables, so OpenWRT can be booted off any supported
device when using a mainline firmware
* sets missing distro boot variables for the downstream firmware
Booting with a downstream firmware is unchanged.
Booting with a mainline firmware now works.
Signed-off-by: Andre Heider <a.heider@gmail.com>
This option is now activated in the generic kernel configuration, no
need to do it for a specific package.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This config option was moved to the generic kernel configuration.
Fixes: ab1bd57656 ("kernel: move F2FS_FS_XATTR and F2FS_STAT_FS symbols to generic")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
u-boot binaries are not useful for these boards, they need to be combined
with atf for a proper firmware.
Signed-off-by: Andre Heider <a.heider@gmail.com>
