The WLAN + WED reset sequence relies on being able to receive interrupts from
the card, in order to synchronize individual steps with the firmware.
When WED is stopped, leave interrupts running and rely on the driver turning
off unwanted ones.
WED DMA also needs to be disabled before resetting.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[Upstream Backport]
The range for the 5 GHz channel 118 was encoded with an incorrect
channel number.
Fixes: ed8e13decc71 (ACS: Extract bw40/80/160 freqs out of acs_usable_bwXXX_chan())
Signed-off-by: Michael Lee <michael-cy.lee@mediatek.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
The raspberypi/userland repository has been deprecated and the RPi tools have
been moved to the raspberrypi/utils repository.
96a7334ae9
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Refresh patches for Linux 6.1 which no longer apply cleanly after
adding patches to fix ethernet rx hang issue on MT7981/MT7986.
Fixes: ede34465de ("mediatek: fix ethernet rx hang issue on MT7981/MT7986")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
-+-------------------------+-
| Model | NIC |
-+-------------------------+-
| All | MT7603 + MT7615 |
-+-------------------------+-
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Some MT7915 calibration data consists of two parts. The first part
"eeprom" size is 0xe00. The second part "precal" size is 0x19c10.
Though some devices may not have precal data, it's better to assume
that precal data exists as no users/developers confirm it. On the
other hand, some devices definitely do not contain precal data
because the EEPROM partition size is smaller than the precal NVMEM
cell size.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
raspberrypi/firmware is about 40G, so getting the full history log isn't an
option.
There have been multiple improvements and also support for the RPi 5 has been
added.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This is the last update for bcm27xx-userland as it has been
deprecated but funcional up to raspberry pi 5.
96a7334 README: Update to make it clear that most code in this repo is deprecated
3c97f76 userland: dtoverlay: /boot/firmware is a valid path
153a235 Assorted clang static analysis fixes
eca070c bcm_host: Update kms/fkms check for pi5
06a7618 dtoverlay: Support bcm2712 as a platform
0489c07 dtoverlay: Add dtoverlay_first/next_subnode
a1c7f81 dtoverlay: Support literal assignments of path strings
44a3953 raspivid: Also flush PTS file if flush is enabled
cc1ca18 userland: dtoverlay: Use os_prefix if set
9d5250f libfdt: Add null-ptr check for prop-data to resolve clang --analyzer warning
50527c6 mmal: Only include Videocore components if not running on Videocore
df245ea tvservice: Update unsupported message to recommend kmsprint
de0cfe8 dtoverlay: Fix clang warnings
0182f05 dtoverlay: Fix various compiler warnings
2a6306b dtoverlay: Fix path rebasing and exports
d1e92d7 dtoverlay: Add support for string escape sequences
b1ee39e gencmd: Add a fallback to mailbox interface if vchiq is not available
54fd97a hello_pi: Fix some build issues
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Innacomm W3400V6 is an xDSL B/G wireless router based on Broadcom
BCM6328 SoC.
SoC: Broadcom BCM6328
CPU: BMIPS4350 V8.0, 320 MHz, 1 core
Flash: SPI-NOR 8MB, MX25L6406E
RAM: 64 MB
Ethernet: 4x 10/100 Mbps
Switch: Integrated
Wireless: 802.11b/g, BCM4312
LEDs/Buttons: 9x / 2x
Flash instruction, web UI:
1. Set a static IP on your computer compatible with 192.168.1.1, i.e
192.168.1.100.
2. Connect the ethernet cable from your computer to the router.
3. Make sure the router is powered off.
4. Press the reset button, don't release it yet!
5. While pressing reset, power on the router.
6. Wait 10 seconds or more.
Note: The power LED is red at first then turns to solid green when
ready.
7. Release the reset button.
8. Browse to 192.168.1.1
9. Select .bin file.
10. Upgrade the image.
11. Wait for it to reboot.
Signed-off-by: Sieng-Piaw Liew <liew.s.piaw@gmail.com>
[Fix cfe nvmem-layout and pinctrl_leds indentation]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The original configuration might be copied from bcm2710 which uses
cortex A53 rather than A72 in BCM2711, without errata might be harmful
to system stability and security.
Signed-off-by: Yangyu Chen <cyy@cyyself.name>
Drop PSGMII PHY patch as it has been moved to generic in preparation for
the PHY driver to be also used for ipq807x SoC as the same PHY is also
used there.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport FIELD_PREP_CONST patch needed for at803x backport patches to
correctly compile and work.
This MACRO is needed to treat values derived from FIELD_PREP usage as
const to be used by switch case or other needed usage.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Part 1 of #13629 split.
* Sets the LAN 2 MAC address in the DTS by deriving it from LAN 1's
address. The factory OS derives this from the `eth1addr` u-boot env
variable, but the nvmem_u-boot-env driver doesn't support parsing MAC
addresses from fields other than `ethaddr`. But for all of the device
samples I've checked (~10) it derives the correct MAC.
* Updates 02_network to ensure that interfaces are assigned to roles
correctly and consistently.
Signed-off-by: Bryan Berg <bdb@north-eastham.org>
Initial backport of at803x PHY driver cleanup. This is in preparation
for split and addition of new PHY Family based on at803x needed for
ipq807x and other IPQ Series SoC.
Other affected patch are automatically refreshed with
make target/linux/refresh
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
It shouldn't gate on the value, since the value will ostensibly
always be set; instead it should depend on the variable being
prepended to being non-empty.
Fixes#14403
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
The register constants were duplicated in net/dsa/rtl83xx/debugfs.c and asm
mach-rtl838x/mach-rtl83xx.h. This commit removes this duplication.
Signed-off-by: Peter Körner <git@mazdermind.de>
According to https://svanheule.net/realtek/maple/register/led_sw_ctrl and also
drivers/net/dsa/rtl83xx/debugfs.c LED_SW_CTRL on the RTL838X should be 0xa00c
not 0x0128. Please note, that is is 0x0128 on the RTL8390/cypress SOC family.
Signed-off-by: Peter Körner <git@mazdermind.de>
the given code-format did not correctly express the condition and made the code
harder to read then necessary.
Signed-off-by: Peter Körner <git@mazdermind.de>
To prevent use of host's library path on Void Linux:
/usr/lib/libacl.so: file not recognized: file format not recognized
collect2: error: ld returned 1 exit status
libtool: error: error: relink 'libgettextlib.la' with the above command before installing it
Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
Fine tuning PR: openwrt/openwrt#14355 Ref: 5a82bb909b
("mediatek: GL-MT6000: Add missing LED state definitions")
As the only LED is using white in the stock firmware when the device is
running and blue for the bootloader I suggest following changes:
- Using blue for the BL and preinit+failsafe
- White for normal operation (like the original FW) and sysupgrade
With this changes it's clear by looking to the LED in which operation
mode the device is and a possible BL stuck can be seen easily.
Tested with [GL-MT6000](https://openwrt.org/toh/gl.inet/gl-mt6000).
Signed-off-by: Thomas Schröder <tschroeder_github@outlook.com>
Tested-by: Hannu Nyman <hannu.nyman@iki.fi>
Enable LED driver LP5562 on HAZE device tree and include its kernel
module package on default package for HAZE.
Signed-off-by: CheWei Chien <chewei.chien@wnc.com.tw>
Add kernel module for lp5562 LED driver.
The kmod-leds-lp5562 depends on kmod-leds-lp55xx-common.
Signed-off-by: CheWei Chien <chewei.chien@wnc.com.tw>
Some devices (MX42CF) have a wrong MAC address configuration. The correct one is located only on the devinfo partition.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
This reduces the size of a single imagebuilder by about 40MB
In example for the target ath79 it would be the sum of generic and <target> directories, so about 16MB,
instead of the whole size of the target directory, about 53MB:
11M target/linux/generic/
3.9M target/linux/ath79/
Signed-off-by: a-gave <agave@dracaena.it>
Add support for configuring rootfs mount options from cmdline.
Rootfs mount options can be passed by declaring in the kernel
cmdline as much options as needed prefixed with "rootfs_mount_options."
An example usage is with rootfs with F2FS filesystem to enable
compress_algorithm to reduce flash wear by compressing the files before
writing to flash.
Example usage:
"... rootfs_mount_options.compress_algorithm=zstd ..."
To pass multiple options:
"... rootfs_mount_options.compress_algorithm=zstd rootfs_mount_options.noinline_data ..."
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
John Audia