The GS110TPP has an RGB LED used for system status indication. Expose
all three components as separate GPIO LEDs connected via the device's
RTL8231.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Since the move to 5.10, there are now two GPIO drivers. The gpio0 node
refers to the internal GPIOs, so the indirect-access-bus-id is no longer
relevant for that node.
Set indirect-access-bus-id to the correct value (31) on the correct node
(gpio1) and enable the device.
Cc: Raylynn Knight <rayknight@me.com>
Cc: Michael Mohr <akihana@gmail.com>
Cc: Stijn Segers <foss@volatilesystems.org>
Cc: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Bjørn Mork <bjorn@mork.no>
Assuming cmdlinepart is only one level deep partition scheme and that
static partition are also defined in DTS, we can assign an of_node for
partition declared from bootargs.
The cmdlinepart parser is the first parser checked and if it does find
some partition declared in the bootargs, every other parser is ignored.
This means that the fixed-partition parser is ignored and an of_node for
the mtd is never assigned.
Fix this by searching a defined of_node using a similar fixed_partition
parsing logig, check if a partition is present with the same label, check
that it has the same offset and size and finally assign an of_node to the
mtd. The NVMEM can now find the of_node for the mtd and correctly works.
Fixes: abc17bf306 ("ath79: convert mtd-mac-address to nvmem implementation")
Tested-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
We were missing (not using) the last sector of each partition,
compared with the output of gparted.
Signed-off-by: Javier Marcet <javier@marcet.info>
[moved the dot]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Enable this option and thus re-include crypt() support for the SHA256,
SHA512 and Blowfish ciphers on all devices. According to commit
9365745f8e ("musl: add a hack to remove unused crypt() algorithms,
saves ~14k after lzma") it should add about ~14k to the resulting image,
which seems to be a reasonable size increase for consistent crypt()
support.
Decided to not remove this hack completely as it might be still useful
for people trying to fit custom images onto smaller devices and the
patch is rather simple so we can afford to keep it for now.
References: https://github.com/openwrt/openwrt/pull/1331
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The UBNT_REVISION was already added for the ubnt-xw target because:
U-boot bootloader on M-XW devices expects factory image revision
version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
(May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
number is actually a number, but in currently generated images there's
OpenWrt text and so the check fails
...
By placing arbitrary correct number first in major version, we make the
bootloader happy and we can flash factory images over TFTP again.
commit d42a7c4699 ("ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery method")
Fixes errors in the form of (tftp flashing):
sent DATA <block=8577, 412 bytes>
received ERROR <code=2, msg=Firmware check failed>
Error code 2: Firmware check failed
The missing UBNT_REVISION was not noticed before, since the
UBNT_REVISION field for the ubnt-xm target was also set to:
"42.OpenWrt-..."
Probably, UBNT_REVISION for the ubnt-xm target was set by the ubnt-xw
and was never overridden somewhere else. However, it is missing and
should be part of the ubnt-xm device.
Signed-off-by: Nick Hainke <vincent@systemli.org>
The firmware for the rtl8723bs chip is now included in the
rtl8723bu-firmware package.
Fixes: 397dfe4a97 ("linux-firmware: Update to version 20121216")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The http://www.us.tcpdump.org mirror will go offline soon, only use the
normal download URL.
Reported-by: Denis Ovsienko <denis@ovsienko.info>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The rtl8723bs firmware was removed and a symlink to the rtl8723bu
firmware was created like it is done in upstream linux-firmware.
The following OpenWrt packages are changing:
* amdgpu-firmware: Multiple updates and new files
* ar3k-firmware: Multiple updates and new files
* ath10k-firmware-qca6174: Updated ath10k/QCA6174/hw3.0/board-2.bin
* bnx2x-firmware: Added bnx2x-e1-7.13.21.0.fw, bnx2x-e1h-7.13.21.0.fw and bnx2x-e2-7.13.21.0.fw
* iwlwifi-firmware-iwl8260c: Updated iwlwifi-8000C-36.ucode
* iwlwifi-firmware-iwl8265: Updated iwlwifi-8265-36.ucode
* iwlwifi-firmware-iwl9000: Updated iwlwifi-9000-pu-b0-jf-b0-46.ucode
* iwlwifi-firmware-iwl9260: Updated iwlwifi-9260-th-b0-jf-b0-46.ucode
* r8169-firmware: Updated rtl8153c-1.fw
* rtl8723bs-firmware: removed
* rtl8723bu-firmware: Added rtlwifi/rtl8723bs_nic.bin symlink
* rtl8822ce-firmware: Updated rtw8822c_fw.bin
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This change enables proper Ethernet link status and speed reporting on
the Ubiquiti UniFi 6 LR access point:
mtk_soc_eth 1b100000.ethernet eth0: PHY [mdio-bus:08] driver [Aquantia AQR112C] (irq=POLL)
mtk_soc_eth 1b100000.ethernet eth0: configuring for phy/2500base-x link mode
mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable Aquantia Ethernet PHY driver as there is an AQR112C 2500Base-T
PHY in the Ubiquiti UniFi 6 LR access point.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Based on: 1ac627024d ("kernel: ath10k-ct: provide a build variant for
small RAM devices")
Like described in the ath10k-ct-smallbuffers version, oom-killer gets
triggered frequently by devices with small RAM.
That change is necessary for many community mesh networks which use
ath10k based devices with too little RAM. The -ct driver has been
proven unstable if used with 11s meshing and only wave2 chipsets are
supporting 11s. Freifunk Berlin is nowadays assembling its
firmware-based completely of vanilla OpenWRT with some package additions
which are made through the imagebuilder. Therefore we cannot take the
approach other freifunk communities have taken to maintain that patch
downstream [1]. Other communities consider these devices as broken and
that change would pretty much give those devices a second life [2].
[1] - 450b306e54
[2] - https://github.com/freifunk-gluon/gluon/issues/1988#issuecomment-619532909
Signed-off-by: Simon Polack <spolack+git@mailbox.org>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Fix default network configuration of the Puzzle-M902 so all LAN ports
are included in the LAN bridge.
Setup network LED to indicate WAN port link status, like vendor
firmware does as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fixes Ethernet link status on all ports and makes 2.5G ports usable
in 2.5G and 1G full-duplex mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Copy and refresh patch enabling AQR112 and AQR412 Ethernet PHY from
layerscape (5.4) target to generic (5.10) as AQR112 can also be found
on other targets as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The auto-ht option already kept HT and VHT support, but wasn't updated
to support HE (11ax).
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Wire up MCU driver for LEDs, fan and temperature sensor, and add
GPIO reset button just like on the M902 also on the Puzzle M901.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Set blinking mode using scheduled work instead of blocking which may
result in deadlocks.
Add dynamic kprintf debugging hexdumps of all MCU rx and tx.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kernel 5.10 is used by many people since quite a while. With other
targets already moved to 5.10, let ath79 follow suit.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ath79/tl-wdr3600; ath79/tl-wdr4300]
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> [ath79/tl-wdr4300]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: David Bauer <mail@david-bauer.net>
This device is based on NXP's QorIQ T2081QDS board, with a quad-core
dual-threaded 1.5 GHz ppc64 CPU and 4GB ECC RAM. The board has 5
ethernet interfaces, of which 3 are connected to the ethernet ports on
the front panel. The other 2 are internally connected to a Marvell
88E6171 switch; the other 5 ports of this switch are also connected to
the ethernet ports on the front panel.
Installation: write the sdcard image to an SD card. Stock U-Boot will
not boot, wait for it to fail then run these commands:
setenv OpenWrt_fdt image-watchguard-firebox-m300.dtb
setenv OpenWrt_kernel watchguard_firebox-m300-kernel.bin
setenv wgBootSysA 'setenv bootargs root=/dev/mmcblk0p2 rw rootdelay=2 console=$consoledev,$baudrate fsl_dpaa_fman.fsl_fm_max_frm=1530; ext2load mmc 0:1 $fdtaddr $OpenWrt_fdt; ext2load mmc 0:1 $loadaddr $OpenWrt_kernel; bootm $loadaddr - $fdtaddr'
saveenv
reset
The default U-Boot boot entry will now boot OpenWrt from the SD card.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
Add a new target named "qoriq", that will support boards using PowerPC
processors from NXP's QorIQ brand.
This doesn't actually add support for any board yet, so that
installation instructions can go in the commit message of the commit
that adds actual support for a board.
Using CONFIG_E6500_CPU here due to the kernel using -mcpu=powerpc64
rather than -mcpu=e5500 when selecting CONFIG_E5500_CPU. The only
difference between e5500 and e6500 is AltiVec support, and the kernel
checks for it at runtime. Musl will only check at runtime if AltiVec
support is disabled at compile-time, so we need to use e5500 in CPU_TYPE
to avoid SIGILL.
Math emulation (CONFIG_MATH_EMULATION_HW_UNIMPLEMENTED) is required, as
neither e5500 nor e6500 implement fsqrt nor fsqrts, and musl hardcodes
sqrt and sqrtf to use these ASM instructions on PowerPC64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
Backport an upstream patch to make libunwind build on ppc64, and add
powerpc64 to the dependencies.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
As of version 3.7, Nettle added PowerPC64 assembly for several
algorithms. Unfortunately, they cause build to fail due to ABI mismatch:
gcm-hash.o: ABI version 1 is not compatible with ABI version 2 output
Disable assembler when ppc64 and musl are used for now.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
Backport an upstream patch that adds support for ELFv2 ABI on big endian
ppc64. As musl only supports ELFv2 ABI on ppc64 regardless of
endianness, this is required to be able to build OpenSSL for ppc64be.
Modify our targets patch to add linux-powerpc64-openwrt, which will use
the linux64v2 perlasm scheme. This will probably break the combination
ppc64 with glibc, but as we really only want to support musl, this
shouldn't be a problem.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
At configuration time, gcc assumes that ppc64be targets use the ELFv1
ABI, and ppc64le targets use the ELFv2 ABI. However, musl libc does not
support the ELFv1 ABI on ppc64 at all, regardless of the endianness.
Therefore, when building for a ppc64 arch and with musl libc, instruct
gcc to use the ELFv2 ABI.
See https://gcc.gnu.org/bugzilla/show_bug.cgi?id=93157 for more info.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
This CPU type is compatible with NXP's PPC based QorIQ processors, and
will be used by the upcoming new qoriq target.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
Backport MFD driver for communicating with the on-board MCU found on
IEI World Puzzle appliances.
Improve the driver to support multiple LEDs, apply a default state and
let MCU take care of blinking if timing is within supported range.
Wire up LEDs and fan for Puzzle M902 in device tree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Provide incoming BSS transition queries to ubus subscribers.
This allows external steering daemons to provide clients with
an optimal list of transition candidates.
This commit has no functional state in case no ubus subscriber is
present or it does not handle this ubus message.
To prevent hostapd from sending out a generic response by itself, a
subscribing daemon has to return a non-zero response code to hostapd.
Signed-off-by: David Bauer <mail@david-bauer.net>
Backport a patch to allow extending the ubus BSS-transition method
for specifying individual dialog tokens for BSS transition
management requests.
This is required for handling BSS transition queries in the future.
Signed-off-by: David Bauer <mail@david-bauer.net>
The UniFi 6 Lite has two MAC addresses for the 2.4 and 5GHz radio in
it's EEPROM partition.
On my unit these are
F4 92 BF A0 BB 6F
F6 92 BF A0 BB 6F
The problem with these is that mac80211 increases the first octet by
2, which leads to conflicting MAC addresses between radios.
Work around this problem for now by increasing the last octet by 1 on
the 5 GHz radio.
Ubiquiti increases the last octet by 2 for each subsequent VAP created
per radio. Ideally we should do the same, however this functionality is
currently lacking from mac80211.
Signed-off-by: David Bauer <mail@david-bauer.net>
