A define dealing with builtin type is wrong. A gnulib update fixes
this, but that requires a new cpio version.
Refresh other patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Further devices from the series have been added in the meantime,
introducing `qca955x_dlink_dap-2xxx.dtsi`.
Thus, merge support for DAP-2695 with the existing dtsi.
This implies factory images can now be flashed via the regular
OEM Web UI, as well as the bootloader recovery.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
This device can be merged with the existing dtsi, which declares
the location of ath9k cal-data via devicetree, correcting the 2.4G
mac address in `10_fix_wifi_mac` rather than `10-ath9k-eeprom`.
To make these changes more visible, apply before merging with dtsi.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
This device can be merged with the existing dtsi,
which will increase spi-max-frequency to 50 MHz.
To make this change more visible, increase to 50 MHz before merging.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
The MikroTik LHG 5 series (product codes RBLHG-5nD, RBLHG-5HPnD and
RBLHG-5HPnD-XL) devices are an outdoor 5GHz CPE with a 24.5dBi or 27dBi
integrated antenna built around the Atheros AR9344 SoC.
It is very similar to the SXT Lite5 series which this patch is based
upon.
Specifications:
- SoC: Atheros AR9344
- RAM: 64 MB
- Storage: 16 MB SPI NOR
- Wireless: Atheros AR9340 (SoC) 802.11a/n 2x2:2
- Ethernet: Atheros AR8229 switch (SoC), 1x 10/100 port,
8-32 Vdc PoE in
- 8 user-controllable LEDs:
- 1x power (blue)
- 1x user (white)
- 1x ethernet (green)
- 5x rssi (green)
See https://mikrotik.com/product/RBLHG-5nD for more details.
Notes:
The device was already supported in the ar71xx target.
Flashing:
TFTP boot initramfs image and then perform a sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Jakob (Jack/XDjackieXD) <jakob@chaosfield.at>
AP6212 wifi need wifi_pwrseq, but from OrangePi Lite 2 dts :
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
clocks = <&rtc 1>;
clock-names = "ext_clock";
reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
post-power-on-delay-ms = <200>;
};
this pwrseq need rtc clock, or kernel won't find this device.
but now rtc-sunxi.c only support A10/A20.
Orangepi Lite 2 use H6 ,from rtc-sun6i.c show compatible is
{ .compatible = "allwinner,sun6i-a31-rtc" },
{ .compatible = "allwinner,sun8i-a23-rtc" },
{ .compatible = "allwinner,sun8i-h3-rtc" },
{ .compatible = "allwinner,sun8i-r40-rtc" },
{ .compatible = "allwinner,sun8i-v3-rtc" },
{ .compatible = "allwinner,sun50i-h5-rtc" },
{ .compatible = "allwinner,sun50i-h6-rtc" },
So it need this to let kernel find this mmc wifi device.
As suggested by hauke, let it build as package.
Signed-off-by: Zhao Yu <574249312@qq.com>
Allows to avoid rpath hacks with at least softethervpn.
--with-pic is needed as it's not default with static libraries, only
shared ones.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The MikroTik RouterBOARD wAPR-2nD (wAP R) router features a miniPCI-e
slot with USB lines connected, which are used by some USB cards with
miniPCI-e form factor, like the R11e-LR8. Enabling USB support is
required for such cards to work.
Tested on a MikroTik wAP LR8 kit (RB wAPR-2nD + R11e-LR8).
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Implement a basic MQPrio support, inserting rules in RX that translate
the TC to prio mapping into vlan prio to queues.
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
Manually rebased:
generic-backport/850-v5.13-usb-ehci-add-spurious-flag-to-disable-overcurrent-ch.patch
All other patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
The crashlog patch as not ported to kernel 5.4.
Fixes: 4e0c54bc5b ("kernel: add support for kernel 5.4")
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
cce5e35 vlist: define vlist_for_each_element_safe
This is change affects only a macro in headers and hence it is not
required to bump ABI_VERSION.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
68961a555e42 ubus: drop dnsmasq check for dns_result method
1ca3e26b8169 bpf: refactor code to support explicit opt-in for bulk+prio detection
3f0acf039f41 bpf: move flow prio/bulk detection config into a separate data structure
bc54c97e3333 map, bpf: create a separate map for configured dscp classes
46cf3eae2d99 bpf: fix bulk flow detaction
88f1db7dd611 bpf: fix priority flow detection
b5dec7874373 bpf: remove access to skb->gso_size
e728a319a9a5 interface: unify status, always include ifname, ingress, egress
Signed-off-by: Felix Fietkau <nbd@nbd.name>
BTF pointer data has a different size on 32 vs 64 bit targets,
and while the generated eBPF code works, the BTF data fails to validate
on mismatch
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since sqm-scripts and qos-scripts packages are in the same category as qosify,
the firsts being in the Base System category, I find it understandable to move
the latter to Base System instead of network section.
Signed-off-by: Rodrigo B. de Sousa Martins <rodrigo.sousa.577@gmail.com>
On systems using brmcfmac (e.g. Raspberry Pi Zero W) without this fix,
the final setup-call:
iw dev wlan0 ibss join ...
fails with returncode 161 and message:
"command failed: Not supported (-95)"
So this patch calls an explicit:
iw dev wlan0 set type ibss
just prior to the 'ibss join' command.
I have tested several ath9k and mt76xx devices
with different revisions: this patch does not harm.
please also apply to stable branch.
Signed-off-by: Bastian Bittorf <bb@npl.de>
There's no such thing as ucidef_set_interfaces_lan. It's
ucidef_set_interface_lan.
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Mark Mentovai <mark@moxienet.com>
bootfs still needs more work before it's ready.
For some unknown reason model RAXE500 uses board id RAX220.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Orange Pi Zero Plus uses a Realtek RTL8211E RGMII Gigabit PHY, but its
currently set to plain RGMII mode meaning that it doesn't introduce
delays.
With this setup, TX packets are completely lost and changing the mode to
RGMII-ID so the PHY will add delays internally fixes the issue.
It looks like this got broken in 5.10 as the PHY RGMII config got fixed
due to datasheet being available and a lot of boards got broken by that.
This has already been sent upstream and received multiple reviews.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This can be used to ensure that the compiled code is up to date, when
something important changes in the toolchain.
A recent example of this is the gcc 11 fix for a code miscompilation issue
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This commit contains a series of fixes for DMA. The burst length
patch significantly improves Ethernet performance. Patches were
tested on the xRX200 and xRX330.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Update Telekom Speedport W921V firmware download URL.
Contained TAPI and VDSL firmware blobs are identical.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enabling KERNEL_FTRACE exposes the HIST_TRIGGERS triggers symbol. Add a
build option for it to fix build failures with KERNEL_FTRACE enabled.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
19aae94 [build: avoid rebuilds of unset VARIANT packages] builds
packages defined without a VARIANT only once, using the first VARIANT
defined in the Makefile.
This caused problems with wpa-cli, as it is only built for variants that
include supplicant support, and the first VARIANT defined may not build
it.
The same happens to hostapd-utils, which is not built for
supplicant-only variants.
To circumvent this, set VARIANT=* for both packages so that they get
built for every defined variant. This should not cause spurious
rebuilds, since tey are not a dependency of any other package defined in
this Makefile.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This allows a package to be rebuilt for all different VARIANTs.
To do so, set VARIANT=*.
The wpa-cli package is not getting built after changes made by
19aae94 [build: avoid rebuilds of unset VARIANT packages], because
wpa-cli is only built when compiling a variant that includes
supplicant support, and the first selected variant may not build it.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Fix mac address increment patch. Permit to overflow to the next
byte and correctly calculate the incremented mac.
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Fixes: d284e6ef0f ("treewide: convert mtd-mac-address-increment* to generic implementation")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Rosen Penev