Set the PHY base address to 12 for mt7530 and 8 for others,
which is based on the default setting for some devices
from printing the register with the following command
after it is written to by uboot during the boot cycle.
`md 0x10117014 1`
PHY_BASE option only uses 5 bits of the register,
bits 16 to 20, so use 8-bit integer type.
Set the option using the DTS property mediatek,ephy-base
and create the gsw node if missing.
Also, added a kernel message to display the EPHY base address.
Note:
If anything is written to a PHY address that is greater than 1 hex char (greater than 0xf)
then there is adverse effects with Atheros switches.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
There are only 2 options in the driver
for the function of mt7620 internal switch port 4:
EPHY mode (RJ-45, internal PHY)
GMAC mode (RGMII, external PHY)
Let the DTS property be boolean instead of string
where EPHY mode is the default.
Fix how the properties are written
for all DTS that use them,
and add missing nodes where applicable,
and remove useless nodes,
and minor DTS formatting.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Like in the previous patch for ath79 target, this will remove the
"devicename" from LED labels in ramips as well.
The devicename is removed in DTS files and 01_leds, consolidation
of definitions into DTSI files is done where (easily) possible,
and migration scripts are updated.
For the latter, all existing definitions were actually just
devicename migrations anyway. Therefore, those are removed and
a common migration file is created in target base-files. This is
actually another example of how the devicename removal makes things
easier.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.
In ramips, we therefore requested to have in the DTS files so far,
and omit it in the DTSI files. However, essentially the syntax of
the parent mtxxxx/rtxxxx DTSI files already determines the DTS
version, so putting it into the DTS files is just a useless repetition.
Consequently, this patch puts the dts-v1 statement into the top-level
SoC-based DTSI files, and removes all other occurences.
Since the dts-v1 statement needs to be before any other definitions,
this also moves the includes accordingly where necessary.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Upstream pinctrl driver in drivers/staging uses
groups/function/ralink,num-gpios instead of
ralink,group/ralink,function/ralink,nr-gpio
Replace these properties in dts as well as the pinctrl driver in
patches-4.14.
This commit is created using:
sed -i 's/ralink,group/groups/g'
sed -i 's/ralink,function/function/g'
sed -i 's/ralink,nr-gpio/ralink,num-gpios/g'
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Hardware
--------
SoC: MediaTek MT7620A
RAM: 64MB
FLASH: 8MB SPI
WLAN: 2G: MediaTek MT7620A
5G: MediaTek MT7610EN
ETH: 1x 10/100/1000M (Atheros AR8035)
LED: RSSI (orange/green)
WiFi 2G (green)
WiFi 5G (green)
Power (green)
System (red / green)
BTN: Power
Reset
LED
WPS
Serial
------
P1 - Tx
P2 - Rx
P3 - GND
P4 - VCC
Pin 4 is the one closest to the LAN port.
MAC overview
------------
WAN *:4c uboot 0x1fc00
2.4 *:4c uboot 0x1fc00
5 *:4e uboot 0x1fc00 +2
Installation
------------
Web interface:
It is possible to upgrade to OpenWrt via the web interface. However, the
OEM firmware upgrade file is required and a tool to fix the MD5 sum of
the header. This procedure overwrites U-Boot and there is not failsafe /
recovery mode present! To prepare an image, you need to take the header
and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and
attach the factory image to it. Then fix the header MD5Sum1.
Serial/TFTP:
You can use initramfs for booting via RAM or flash the image directly.
Additional Notes:
If the web interface upgrade fails, you have to open your device and
attach serial console. Since the web upgrade overwrites the boot loader,
you might also brick your device.
In order to flash back to stock, the first header and U-Boot needs to be
stripped from the original firmware.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[change rssi LED labels]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Michael Pratt
Adrian Schmutzler