target/linux/ar71xx/patches-4.4/103-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch
has been applied upstream; the two deleted brcm2708 patches have been
useless even before (as the second one only reverted the first one).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
These two patches:
target/linux/ar71xx/patches-4.4/403-mtd_fix_cfi_cmdset_0002_status_check.patch
target/linux/ramips/patches-4.4/0036-mtd-fix-cfi-cmdset-0002-erase-status-check.patch
are replaced by upstream commit 242dbd2b3df ("mtd: cfi_cmdset_0002:
Change erase functions to check chip good only")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some NBG6716 do not have ath10k calibration data in flash, only in chip
OTP. To determine if flash has a valid calibration data, the first two
bytes telling the length of the calibration data are checked against the
requested length. If the lengths match, calibration data is valid and
read from flash.
Signed-off-by: Matti Laakso <matti.laakso@outlook.com>
This devices always looses the settings after power loss, nothing is
been saved.
Deactivate building this image till this problem is fixed.
See FS#672
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix ART offset (make it universal for 8/16 MB versions of the board) and
while at it, include also GPIO setup for h/w watchdog (EM6324QYSP5B).
Fixes: FS#1532
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Some Ubiquiti U-boot versions, in particular the "U-Boot 1.1.4.2-s956
(Jun 10 2015 - 10:54:50)" found with AirOS 5.6, do not correctly flush the
caches for the whole kernel address range after decompressing the kernel
image, leading to hard to debug boot failures, depending on kernel version
and configuration.
As a workaround, prepend the relocate-kernels loader, which will invalidate
the caches after moving the kernel to the correct load address.
Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Previously, tplink_pharos_check_image() would accept any image with ELF
magic and only non-printable data in the support-list, as in this case the
while-read loop would not run at all. Add the new support-list offset and
ensure an image is only accepted when the model string is actually found.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This bumps the 4.4. kernel in LEDE 17.01 to 4.4.116.
More Meltdown & Spectre mitigation.
* Refresh patches.
* Refresh x86/config for RETPOLINE.
* Deleted 8049-PCI-layerscape-Add-fsl-ls2085a-pcie-compatible-ID.patch (accepted upstream)
* Deleted 8050-PCI-layerscape-Fix-MSG-TLP-drop-setting.patch (accepted upstream)
* 650-pppoe_header_pad.patch does not apply anymore (code was replaced).
Bumps from 4.4.113 to 4.4.115 were handled by Kevin Darbyshire-Bryant.
Compile-tested on: ar71xx, ramips/mt7621, x86/64
Run-tested on: ar71xx, ramips/mt7621, x86/64
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
The Netgear WNR2000v4 does not have a USB port. Hence, including USB packages into the default images is useless.
It looks like the WNR2000v4 definition in master is OK.
v2 fixes the silly typo in the patch title (WNR2000v4 instead of WNR200v4)
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Bump 4.4 to 4.4.107 and refreshed all patches.
Made the following patch for Mediatek and Oxnas compatible with kernel 4.4.107:
0072-mtd-backport-v4.7-0day-patches-from-Boris.patch
Compile-tested: ar71xx
Run-tested: ar71xx
Signed-off-by: Etienne Haarsma <bladeoner112@gmail.com>
Reviewed-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Rosen Penev <rosenp@gmail.com>
This patch fixes the switch port numbering on Mikrotik RB750r2 (hEX lite) and RB750UPr2 (hEX PoE lite).
Tested on a RB750UPr2. Maybe this patch is applicable to other devices (e.g. RB951Ui-2nD, RB952Ui-5ac2nD) but I have no way to test them.
Signed-off-by: João Chaínho <joaochainho@gmail.com>
(cherry picked from commit 61027e3430)
This fixes the LED configuration for the D-Link DIR-869 A1. In order to
support the device I probed around using an initramfs image for the
UniFi AC. Pulling GPIO 15 to low enabled the LEDs while high disabled them.
GPIO 16 set to low meant that the color was white while pulling it to high
made the color change to orange. The past code was written based upon these
findings.
However, running a flashed image I now discovered that GPIO 15 controls the
orange LEDs while GPIO 16 controls the white ones and that both are active
when low. This means that the GPIOs were inverted and one active_low was set
wrong which this patch fixes.
Behavior of the LED front after this patch is applied:
cat /sys/devices/platform/leds-gpio/leds/d-link:white:status/brightness
0 -> white LEDs are OFF
255 -> white LEDs are ON
cat /sys/devices/platform/leds-gpio/leds/d-link🍊status/brightness
0 -> orange LEDs are OFF
255 -> orange LEDs are ON
If the brightness of both is set to 255 the LED front will be white.
If the brightness of both is set to 0 the LED front will be off.
Signed-off-by: Florian Beier <beier.florian@gmail.com>
A default rssileds config exists for the TP-Link WA850RE v1 but the
rssiled package is not included by default.
The compressed 17.01.3 image size increases by 3302 bytes which should
be tolerable even for a 4MB flash board.
Fixes: FS#1043
Signed-off-by: Mathias Kresin <dev@kresin.me>
The addresses were read from the 'config' partition, which would not always
contain the addresses at the same offsets, depending on the stock firmware
version used before flashing LEDE. Change this to get the addresses from
the 'product-info' partition, which is read-only.
Reported-and-tested-by: Andreas Ziegler <ml@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
ALFA Network AP121F is a pocket-size router dedicated for VPN/TOR users.
Device is based on Atheros AR9331 WiSoC and is running a custom version
(updated from OpenWrt CC to LEDE 17.01 release) of NetAidKit firmware.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz
- 1x microSD (optional, on separate PCB)
- 3x LED, 1x button, 1x switch
- UART header on PCB
Flash instruction (under U-Boot web recovery mode):
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
wait for first blink of all LEDs (indicates network setup), then keep
button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Non-US versions of the TP-Link TL-WR710N v1 don't have a region code so
far, so we can just set US unconditionally.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
If nand chip has no NAND_NO_SUBPAGE_WRITE flag on its options
ubifs can't use it mtd devices and the kernel crashes with error:
__nand_correct_data: uncorrectable ECC error
Signed-off-by: Sergey Sergeev <adron@yapic.net>
This fixes wrong GPIO numbers for LEDs and button in Wallys DR344 board
and sets color of all LEDs to green as the mass production boards have
only green one.
Actually, DR344 has 6 GPIO-connected LEDs and one button:
- GPIO11: status
- GPIO12: sig1
- GPIO13: sig2
- GPIO14: sig3
- GPIO15: sig4
- GPIO16: reset button
- GPIO17: lan
WAN LED is connected directly with AR8035 PHY.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This aligns default network interfaces configuration with vendor
firmware: GE (eth0) -> wan, FE (eth1) -> lan.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
GMAC0 interface of AR9344 SOC in Wallys DR344 board is connected with
AR8035, not with AR8327. Without this fix, GE interface doesn't work at
all or shows high packet loss ratio.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Bump the 17.01 tree kernel to 4.4.69. Trunk 4.4 and 17.01 4.4 have diverged, talked this
through with jow, he was okay with a clean diff against 17.01 and not a backported trunk
patch.
The following patches were applied upstream:
* 062-[1-6]-MIPS-* series
* 042-0004-mtd-bcm47xxpart-fix-parsing-first-block
Reintroduced lantiq/patches-4.4/0050-MIPS-Lantiq-Fix-cascaded-IRQ-setup, as
it was incorrectly included upstream thus dropped from LEDE, but subsequently
reverted upstream. Thanks to Kevin Darbyshire-Bryant for pointing me to it.
Compile-tested on: ar71xx, ramips/mt7621, x86/64.
Run-tested on: ar71xx, ramips/mt7621, x86/64.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
Fix a '==' that should be a '=' in a test condition. Busybox fortunately
doesn't care.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This router has the same hardware as TP-LINK TL-WR841N/ND v11 (same FCC
ID, same TFTP image name...).
If the stock firmware web interface doesn't accept LEDE factory image,
it can be flashed via the U-Boot TFTP recovery mode, by long-pressing
the reset button after power on.
The TFTP image name is wr841nv11_tp_recovery.bin (yes, v11, not v12).
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
platform_find_rootfspart() fails if the kernel partition comes before the
rootfs partition. The proposed patch fixes this while preserving what I
understand was the original idea: stop at first match.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Hauke Mehrtens