This adds support for the MikroTik RouterBOARD RBD53iG-5HacD2HnD
(hAP ac³), a indoor dual band, dual-radio 802.11ac
wireless AP with external omnidirectional antennae, USB port, five
10/100/1000 Mbps Ethernet ports and PoE passthrough.
See https://mikrotik.com/product/hap_ac3 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4019
- RAM: 256 MB
- Storage: 16 MB NOR + 128 MB NAND
- Wireless:
· Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
· Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi antennae
- Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in, PoE passtrough on port 5
- 1x USB Type A port
Installation:
1. Boot the initramfs image via TFTP
2. Run "cat /proc/mtd" and look for "ubi" partition mtd device number, ex. "mtd1"
3. Use ubiformat to remove MikroTik specific UBI volumes
* Detach the UBI partition by running: "ubidetach -d 0"
* Format the partition by running: "ubiformat /dev/mtdN -y"
Replace mtdN with the correct mtd index from step 2.
3. Flash the sysupgrade image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
Tested-by: Mark Birss <markbirss@gmail.com>
Tested-by: Michael Büchler <michael.buechler@posteo.net>
Tested-by: Alex Tomkins <tomkins@darkzone.net>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Cell C RTL30VW is a LTE router with tho gigabit ethernets and integrated
QMI mPCIE modem.
This is stripped version of ASKEY RTL0030VW.
Hardware:
Specification:
-CPU: IPQ4019
-RAM: 256MB
-Flash: NAND 128MB + NOR 16MB
-WiFi: Integrated bgn/ac
-LTE: mPCIe card (Modem chipset MDM9230)
-LAN: 2 Gigabit Ports
-USB: 2x USB2.0
-Serial console: RJ-45 115200 8n1
-Unsupported VoIP
Known issues:
None so far.
Instruction install:
There are two methods: Factory web-gui and serial + tftp.
Web-gui:
1. Apply factory image via stock web-gui.
Serial + initramfs:
1. Rename OpenWrt initramfs image to "image"
2. Connect serial console (115200,8n1)
3. Set IP to different than 192.168.1.11, but 24 bit mask, eg. 192.168.1.4.
4. U-Boot commands:
sf probe && sf read 0x80000000 0x180000 0x10000
setenv serverip 192.168.1.4
set fdt_high 0x85000000
tftpboot 0x84000000 image
bootm 0x84000000
5. Install sysupgrade image via "sysupgrade -n"
Back to stock:
All is needed is swap 0x4c byte in mtd8 from 0 to 1 or 1 to 0,
do firstboot and factory reset with OFW:
1. read mtd8:
dd if=/dev/mtd8 of=/tmp/mtd8
2. go to tmp:
cd /tmp/
3. write first part of partition:
dd if=mtd8 of=mtd8.new bs=1 count=76
4. check which layout uses bootloader:
cat /proc/mtd
5a. If first are kernel_1 and rootfs_1 write 0:
echo -n -e '\x00' >> mtd8.new
5b. If first are kernel and rootfs write 1:
echo -n -e '\x01' >> mtd8.new
6. fill with rest of data:
dd if=mtd8 bs=1 skip=77 >> mtd8.new
7. CHECK IF mtd8.new HAVE CHANGED ONLY ONE BYTE! e.g with:
hexdump mtd8.new
8. write new mtd8 to flash:
mtd write mtd8.new /dev/mtd8
9. do firstboot
10.reboot
11. Do back to factory defaults in OFW GUI.
Based on work: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
MeshPoint.One is Wi-Fi hotspot and smart IoT gateway (based upon
Jalapeno module from 8Devices).
MeshPoint.One (https://meshpointone.com) is a unique Wi-Fi hotspot and
smart city gateway that can be installed and powered from street
lighting (even solar power in the future). MeshPoint provides up to 27
hours of interrupted Wi-Fi and IoT services from internal battery even
when external power is not available. MeshPoint.One can be used for
disaster relief efforts in order to provide instant Wi-Fi coverage that
can be easily expanded by just adding more devices that create wide area
mesh network. MeshPoint.One devices have standard Luci UI for
management.
Features:
- 1x 1Gpbs WAN
- 1x 1Gbps LAN
- POE input (eth0)
- POE output (eth1)
- Sensor for temperature, humidity and pressure (Bosch BME280)
- current, voltage and power measurement via TI INA230
- Hardware real time clock
- optional power via Li-Ion battery
- micro USB port with USB to serial chip for easy OpenWrt terminal
access
- I2C header for connecting additional sensors
Installation:
-------------
Simply flash the sysupgrade image from stock firmware.
Or use the built in Web recovery into bootloader:
Hold Reset button for 5 to 20 seconds or use UART and httpd command.
Web UI will appear on 192.168.2.100 by default.
For web recovery use the factory.ubi image.
Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
Signed-off-by: Damir Franusic <damir.franusic@sartura.hr>
Signed-off-by: Valent Turkovic <valent@meshpoint.me>
Signed-off-by: Robert Marko <robert@meshpoint.me>
[commit description long line wrap, usb->USB]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
* QCA IPQ4028
* 256 MB of RAM
* 32 MB of SPI NOR flash (mx25l25635e)
* 128 MB of SPI NAND flash (gd5f1gq4ucy1g)
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- uses AP-DK03 BDF from QCA4019/hw1.0/board-2.bin
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- uses AP-DK03 BDF from QCA4019/hw1.0/board-2.bin
* 2 fully software controllable GPIO-LEDs
* 2 additional GPIO-LEDs which also affect the SIM card detection
* 1x button (reset)
* 1x GPIO buzzer
* 1x USB (xHCI)
* 1x NGFF (USB-only with Dual-SIM support, untested)
* TTL pins are on board (R124 is next to GND, then follows: RX, TX, VCC)
* 2x gigabit ethernet
- phy@mdio4:
+ Manual: Ethernet port 0
+ gmac0 (ethaddr) in original firmware
+ 802.3af POE (HV version)
+ 24v passive POE (LV version)
- phy@mdio3:
+ Manual: Ethernet port 1
+ gmac1 (eth1addr) in original firmware
* DC Jack connector
+ 24-56V (HV version)
+ 12-24V (LV version)
The SPI NAND flash isn't supported at the moment.
The bootloader has to be updated before OpenWrt is installed to fix a
reboot problem. The nor-ipq40xx-single.img from
https://downloads.compex.com.sg/?dir=uploads/QSDK/QCA-Reference/WPJ428/b170123-IPQ40xx-Reference-Firmware
has to be downloaded and the transfered in u-boot via TFTP
set ipaddr 192.168.1.11
set serverip 192.168.1.10
ping ${serverip}
tftpboot 0x84000000 nor-ipq40xx-single.img
imgaddr=0x84000000 && source $imgaddr:script
The sysupgrade image can be installed directly on flash using u-boot:
sf probe
tftpboot 0x84000000 openwrt-ipq40xx-compex_wpj428-squashfs-sysupgrade.bin
sf erase 0x00180000 +$filesize
sf write 0x84000000 0x00180000 $filesize
bootipq
The initramfs image can be started using
tftpboot 0x82000000 openwrt-ipq40xx-compex_wpj428-initramfs-fit-uImage.itb
set fdt_high 0x83000000
bootm 0x82000000
The used SIM card slot can be changed using
# slot 1 (also enables orange LED)
echo 1 > /sys/class/gpio/gpio3/value
# slot 2
echo 0 > /sys/class/gpio/gpio3/value
It can be checked whether a SIM card is inserted in the current slot and
the red LED is subsequently on via:
echo 2 > /sys/class/gpio/export
cat /sys/class/gpio/gpio2/value
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Robert Marko
Adrian Schmutzler