Commit Graph

59867 Commits

Author SHA1 Message Date
Hauke Mehrtens 387fde0da0 kernel: bump 5.15 to 5.15.150
Removed because it is upstream:
bcm53xx/patches-5.15/030-v5.16-0019-ARM-dts-BCM53573-Describe-on-SoC-BCM53125-rev-4-swit.patch
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=cb1003c07e746e4e82bdd3959c9ea37018ed41a3

Removed because it is upstream:
bcm53xx/patches-5.15/037-v6.6-0004-ARM-dts-BCM53573-Drop-nonexistent-default-off-LED-tr.patch
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=c65a23e98e38dc991f495d6bdb3cfa6163a88a0c

Removed because it is upstream:
bcm53xx/patches-5.15/037-v6.6-0005-ARM-dts-BCM53573-Drop-nonexistent-usb-cells.patch
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=71475bcee001cae3844644c2787eef93b26489d1

Adapted hack-5.15/650-netfilter-add-xt_FLOWOFFLOAD-target.patch to match
the changes from the upstream flow offload patch:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=7c71b831220edeab7ce603d818dc1708d9ea4137

Manually Adapted the following patch:
bcm53xx/patches-5.15/035-v6.2-0004-ARM-dts-broadcom-align-LED-node-names-with-dtschema.patch

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-03-07 19:30:54 +01:00
Hauke Mehrtens 26d1d52403 kernel: bump 5.15 to 5.15.149
Removed because it is upstream:
generic/pending-5.15/540-ksmbd-only-v2-leases-handle-the-directory.patch
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=81ea755b8fa57ce186f56f14b709cf491c2a5505

Manually Adapted the following patch:
ath79/patches-5.15/900-unaligned_access_hacks.patch

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-03-07 19:30:54 +01:00
Robert Marko e247763617 ath25: drop target
ath25 has been on life support for the last couple of releases, eventually
leading to marking it as source-only in 2023.

It has been basically only touched to do a kernel bump so that we can make
the new OpenWrt release which was a challenge due to small RAM amount.

However, with the attempt of kernel 6.1 update it turns out that kernel
cannot even finish booting due to RAM constraints, so its time to let this
target go.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-03-07 12:15:51 +01:00
Sven Eckelmann 71411cb8b8 ath11k-firmware: Move from kvalo to new upstream repository
It was announced [1] that the original staging repositories are no longer
used for staging of new firmware binaries. And that the old repository will
be removed [2] in June 2024.

The ath11k-firmware package must therefore point to the new repository
before the old one is no longer accessible.

[1] https://lore.kernel.org/r/bac97f31-4a70-4c4c-8179-4ede0b32f869@quicinc.com
[2] 8d2cc160f3

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2024-03-07 09:37:42 +01:00
Robert Marko 5b1d6d4607 kernel: crypto: add SHA512 ARM64 ASM optimized module
Kernel has an ASM optimized version of SHA512 that was ported from
OpenSSL, so lets package it as it provides significant perfomance
improvement compared to the generic implementation.

There is a Cryptographic Extension based version as well, but that relies
on ARMv8.2 ISA which I am not aware any of the OpenWrt supported SoC-s use.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-03-06 22:00:58 +01:00
Robert Marko 4443470a57 kernel: crypto: add SHA2(224 and 256) ARM64 CE optimized module
Kernel has optimized version of SHA2(224 and 256) using the ARMv8 Crypto
Extensions, so lets package it.

Use it by default for qualcommax as it uses Cortex-A53 core and has ARMv8
CE extensions present.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-03-06 18:38:28 +01:00
Robert Marko 09207c0348 kernel: crypto: add SHA256 ARM64 ASM optimized module
Kernel has an ASM optimized version of SHA256 that was ported from
OpenSSL, so lets package it as it provides significant perfomance
improvement compared to the generic implementation.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-03-06 18:30:21 +01:00
Robert Marko 9425064bdb kernel: crypto: add SHA1 ARM64 CE optimized module
Kernel has optimized version of SHA1 using the ARMv8 Crypto Extensions,
so lets package it.

Use it by default for qualcommax as it uses Cortex-A53 core and has ARMv8
CE extensions present.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-03-06 12:16:11 +01:00
Weijie Gao d40d64fc62 cryptodev-linux: update to 1.13
Update to 1.13 with upstream backports.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2024-03-06 10:17:45 +01:00
Robert Marko fdb563c1a5 kernel: qca-ssdk: refresh PCS patch
Recently added PCS patch requires a refresh, so lets do it.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-03-05 21:43:54 +01:00
Robert Marko 3e6f64d443 kernel: crypto: package SHA3
SHA3 is now required by jitterentropy_rng in kernel 6.6, so lets start
preparing by packaging SHA3 support as its supported in 5.15 and 6.1
kernels as well.

AFAIK, only ARMv8.2 has a crypto extension for SHA3, however I am not aware
of any SoC we support that uses ARMv8.2 ISA so its not enabled currently.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-03-05 20:23:46 +01:00
Rafał Miłecki 4efbfcd996 base-files: sysupgrade: handle errors when generating backup
1. Return error if any step of generating tar file fails
2. Use pipefail to avoid calling "gzip" if tar failed

Fixes: e36cc53092 ("base-files: sysupgrade: use tar helper to include installed_packages.txt")
Reported-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Cc: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Cc: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-03-05 11:54:55 +01:00
Dirk Buchwalder 93610492b6 qualcommax: ipq60xx: add support for netgear wax214
Netgear WAX214 is a 802.11 ax dual-band AP
    with PoE. (similar to Engenius EWS357APV3)

    Specifications:

        •     CPU: Qualcomm IPQ6010 Quad core Cortex-A53
        •     RAM: 512MB of DDR3
        •     Storage: 128MB NAND (Macronix MX30UF1G18AC)
        •     Ethernet: 1x 1G RJ45 port (QCA8072) PoE
        •     WIFI:
              2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate
              5GHz: Qualcomm QCN5052 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate

        •     LEDs:
              4 x GPIO-controlled LEDs
                - 1 Power LED (orange)
                - 1 LAN LED (blue)
                - 1 WIFI 5g LED (blue)
                - 1 WIFI 2g LED (blue)
                black_small_square  Buttons: 1x soft reset
                black_small_square  Power: 12V DC jack or PoE (802.3af )

            An populated serial header is onboard, format is
             1.25mm 4p (DF13A-4P-1.25H)
            RX/TX is working, bootwait is active, secure boot is not
            enabled.

            The root password of the stock firmware is unknown,
            but failsafe mode can be entered to reset the password.

            Installation Instructions:

                - obtain serial access
                - stop auto boot (press "4", Entr boot command line
		  interface)
                - setenv active_fw 0 (to boot from the primary rootfs,
                  or set to 1 to boot from the secondary rootfs
                  partition)
                - saveenv

                - tftpboot the initramfs image
                - bootm

                - copy
		  openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
                  to the device
                - write the image to the NAND:
                   - cat /proc/mtd and look for rootfs partition (should
		     be mtd11,
                     or mtd12 if you choose active_fw 1)
                   - ubiformat /dev/mtd11 -f -y
		     openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
                - reboot

            Note: the firmware is senao-based. But I was unable to build
                  a valid senao-header into the image.
                  Maybe they changed the header format and senaoFW isn't
                  working any more.

Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2024-03-05 06:34:35 +01:00
Dirk Buchwalder e8a2fd241d ipq-wifi: update to version 2024-03-04
The new version adds support for the Netgear WAX214.

Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2024-03-05 06:34:35 +01:00
John Audia 13cdc8955c kernel: bump 6.1 to 6.1.80
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.80

Manually rebased:
	generic/hack-6.1/650-netfilter-add-xt_FLOWOFFLOAD-target.patch[1]

All other patches automatically rebased.

1. Acknowledgement to @heheb and @DragonBluep. Upstream commit for ref: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.80&id=9c5662e95a8dcc232c3ef4deb21033badcd260f6

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2024-03-05 00:23:59 +01:00
John Audia bd6b37f463 kernel: Remove dsmark support
dsmark support was removed in kernel 5.15.150 and 6.1.80. Remove it from
the kmod package as well

Signed-off-by: John Audia <therealgraysky@proton.me>
2024-03-05 00:23:59 +01:00
Matthias Schiffer 2b46cbef81
build: do not depend on $(STAGING_DIR)/.prepared when in SDK
The dependency can't be satisfied when building using the SDK, breaking
package builds. As the staging and bin dirs are distributed with the SDK
archive, ignoring the dependency is fine when SDK is set.

Fixes: fbb924abff ("build: add $(STAGING_DIR) and $(BIN_DIR) ...")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2024-03-04 23:45:15 +01:00
Álvaro Fernández Rojas fe0081eecf bcm27xx: use PARTUUID for root in cmdline
This allows booting from USB/NVME while keeping SD compatibility.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2024-03-04 16:28:57 +01:00
Álvaro Fernández Rojas 4b3c1251a4 base-files: sysupgrade: allow overriding config restore
Some platforms like Raspberry Pi require patching some backup files like
cmdline.txt in order to set the correct root PARTUUID.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2024-03-04 16:27:39 +01:00
Álvaro Fernández Rojas fb80be6944 bcm27xx: pass signature to partition generation
Passes IMG_PART_SIGNATURE to ptgen instead of using the default "OWRT"
signature.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2024-03-04 16:27:39 +01:00
Álvaro Fernández Rojas 552c6b2472 bcm27xx: base-files: fix platform_copy_config
/boot/kernel*.img wildcard only works without quotation marks.

Fixes: 1a5e51ab00 ("bcm27xx: base-files: fix platform_copy_config")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2024-03-04 16:20:55 +01:00
Álvaro Fernández Rojas 5cd8e037b5 bcm63xx: drop target
BCM63xx maintainance is a PITA since there's no full Device Tree support and
therefore every board needs it's own definition in board_bcm963xx.c
There's no DSA support for this board and there have been very few
contributions in the last years.
Moreover, BCM63xx SoCs >= BCM6358 are already supported in bmips target, so
any efforts to keep this target alive aren't worth the time.
Let's focus the community efforts on improving bmips instead.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2024-03-04 16:12:21 +01:00
Jo-Philipp Wich 6f6406a132 base-files: sysupgrade: fix streaming backup archives to stdout
Due to previous refactoring in sysupgrade, writing backup archives to
stdout became impossible since the hardcoded gzip output redirection
did not account for the `-` special case filename.

Fix this issue by substituting `-` with `/proc/self/fd/1` in the tar
archive output path variable.

Also remove a redundant `rm -f` of the target file path that occurs
before the file could've possibly been written.

Fixes: #14773
Fixes: https://github.com/openwrt/luci/issues/6961
Fixes: e36cc53092 ("base-files: sysupgrade: use tar helper to include installed_packages.txt")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2024-03-04 14:58:10 +01:00
Matthias Schiffer fbb924abff
build: add $(STAGING_DIR) and $(BIN_DIR) preparation to target and package subdir compile dependencies
In a pristine build, these directories are created as dependencies of
the tools subdir compile, however this step never runs when the tools
compile stamp already exists. Since commit ed6ba2801c ("tools: keep
stamp file in $(STAGING_DIR_HOST)"), this will happen after `make clean`:
$(STAGING_DIR) has been deleted, but the tools stamp still exists, so
the next build will fail because $(STAGING_DIR) has not been set up
correctly.

Fix builds after `make clean` by adding the preparation as dependencies
for the target and package directories as well.

Fixes: ed6ba2801c ("tools: keep stamp file in $(STAGING_DIR_HOST)")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2024-03-03 23:13:59 +01:00
Daniel Golle 37bbed6f95 kernel: lantiq: ltq-vmmc: introduce user group for vmmc
asterisk-chan-lantiq is by now the only user of the VMMC interface.
And asterisk runs as user 'asterisk' which doesn't give it permission
to open the /dev/vmmc* devices.
Introduce a new user group 'vmmc' and give permission to access the
/dev/vmmc* devices to that group.
Another commit for asterisk-chan-lantiq will add the 'asterisk' user
to that group.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-03-03 15:44:52 +00:00
Tobias Schramm 336a531c15 mvebu: add support for SolidRun ClearFog Pro
The SolidRun ClearFog Pro is a router based on the SolidRun CN9130 SOM.

Specs:
 - SoC: Quad-Core Cortex-A72 CN9130 SoC
 - RAM: 4GiB DDR4
 - Serial: Micro-USB port on front (FT232R, 115200 8n1)
 - Storage: 8GiB eMMC, microSD card slot, 8MiB SPI NOR flash
 - Ethernet: 7x GbE (1 port dedicated on SoC, 6 port switch with single GbE CPU port)
 - SFP: 1x SFP+
 - USB: 1x USB-A 3.1 Gen 1
 - PCIe: 2x mini PCIe (one slot with USB and SIM card socket)
 - SATA: 1x M.2 Key-B

In addition to the usual connectivity options this device also features
an internal mikroBUS expansion connector.

SATA is currently untested due to lack of a suitable M.2 SSD.

Installation
============

1. Write sdcard sysupgrade image to microSD card using dd or similar
2. Insert microSD card into router and apply power
3. Device boots into OpenWRT
4. (optional) dd sysupgrade image to /dev/mmcblk0 to install to eMMC

Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
2024-03-02 14:21:20 +01:00
Tobias Schramm 1ed01ef606 kernel: 6.1: backport Marvell Armada 8k AP807 cpufreq support
Upstream a patch adding support for cpufreq on AP807-based SoC like the
CN913x was submitted. Include it in patches to ensure best performance
under load and lowest power consumption in idle.

Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
2024-03-02 14:21:20 +01:00
Tianling Shen 4f668091bf u-boot.mk: override default PATH to avoid pick hostpkg python
hostpkg python from packages feed can be picked when do a incremental
build because hostpkg has higher priority in PATH. It may lead build
faliure as it's heavily trimmed (e.g. lacks necessary modules).

For uboot which uses binman and intree dtc, this is forced as hostpkg
python will never provide those modules by default.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-03-02 14:17:31 +01:00
Paul Geraedts 8256d06933 mediatek: filogic: fix failsafe mode on devices with no lan1
Default to lan4 port, instead of (missing) lan1 port,
to fix failsafe mode on Xiaomi AX3000T, WR30U, AX6000

Build system: x86/64
Build-tested: mediatek/filogic/xiaomi_mi-router-ax3000t-ubootmod
Run-tested: mediatek/filogic/xiaomi_mi-router-ax3000t-ubootmod

Signed-off-by: Paul Geraedts <p.f.j.geraedts@gmail.com>
2024-03-02 14:08:08 +01:00
Pawel Dembicki 766e688b30 ls-mc: bump to 10.38.0
Update ls-mc to latest 10.38.0 version.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2024-03-02 14:08:08 +01:00
Pawel Dembicki 16d9d91fed ls-dpl: bump to 10.38.0
Update ls-dpl to latest 10.38.0 version.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2024-03-02 14:08:08 +01:00
INAGAKI Hiroshi b18edb1bfa ath79: add support for ELECOM WAB-I1750-PS
ELECOM WAB-I1750-PS is a 2.4/5 GHz band 11ac (Wi-Fi 5) access point,
based on QCA9558.

Specification:

- SoC              : Qualcomm Atheros QCA9558
- RAM              : DDR2 128 MiB (2x Winbond W9751G6KB251)
- Flash            : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G)
- WLAN             : 2.4/5 GHz 3T3R
  - 2.4 GHz        : Qualcomm Atheros QCA9558 (SoC)
  - 5 GHz          : Qualcomm Atheros QCA9880
- Ethernet         : 2x 10/100/1000 Mbps
  - phy ("PD")     : Atheros AR8035
  - phy ("PSE")    : Atheros AR8033
- LEDs/keys (GPIO) : 3x/3x
- UART             : 2x RJ-45 port
  - "SERVICE"      : TTL (3.3V)
    - port         : ttyS0
    - assignment   : 1:3.3V, 2:GND, 3:TX, 4:RX
    - settings     : 115200n8
    - note         : no compatibility with "Cisco console cable"
  - "SERIAL"       : RS232C (+-12V)
    - port         : ?
    - assignment   : 1:NC , 2:NC , 3:TXD, 4:GND,
                     5:GND, 6:RXD, 7:NC , 8:NC
    - settings     : 115200n8
    - note         : compatible with "Cisco console cable"
- Buzzer           : 1x GPIO-controlled
- USB              : 1x USB 2.0 Type-A
- Power            : DC jack or PoE
  - DC jack        : 12 VDC, 1.04 A (device only, rating)
  - PoE            : 802.3af/at, 48 VDC, 0.26 A (device only, rating)
  - note           : supports 802.3af supply on PSE (downstream) port
                     when powered by DC adapter or 802.3at PoE

Flash instruction using factory.bin image:

1. Boot WAB-I1750-PS without no upstream connection (or PoE connection
   without DHCP)
2. Access to the WebUI ("http://192.168.3.1") on the device and open
   firmware update page
   ("ツールボックス" -> "ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update
   ("アップデート") button
4. Wait ~120 seconds to complete flashing

Revert to OEM firmware:

1. Download the latest OEM firmware
2. Remove 128 bytes(0x80) header from firmware image
3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val)
4. Upload the decoded firmware to the device
5. Flash to "firmware" partition by mtd command
6. Reboot

Notes:

- To use the "SERVICE" port, the connection of 3.3V line is also
  required to enable console output.
  The uart line of "SERVICE" is branched out from the internal pin
  header with 74HC126D and 3.3V line is connected to OE pin on it.

- "SERIAL" port is provided by HS UART on QCA9558 SoC that has
  compatibility with qca,ar9330-uart, but QCA955x SoC's is not supported
  on Linux Kernel and OpenWrt.

- To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC
  3.5 A adapter is recommended. (official: WAB-EX-ADP1)

MAC addresses:

Ethernet (PD, PSE): 00:90:FE:xx:xx:0A (Config, ethaddr (text))
2.4GHz            : 00:90:FE:xx:xx:0A (Config, ethaddr (text))
5GHz              : 00:90:FE:xx:xx:0B

[original work]
Signed-off-by: Yanase Yuki <dev@zpc.st>
[update for NVMEM and others]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-03-02 14:08:08 +01:00
INAGAKI Hiroshi 8e72fa8b6f ath79: add support for ELECOM WAB-S1167-PS
ELECOM WAB-S1167-PS is a 2.4/5 GHz band 11ac (Wi-Fi 5) access point,
based on QCA9557.

Specification:

- SoC              : Qualcomm Atheros QCA9557
- RAM              : DDR2 128 MiB (2x Winbond W9751G6KB251)
- Flash            : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G)
- WLAN             : 2.4/5 GHz 2T2R
  - 2.4 GHz        : Qualcomm Atheros QCA9557 (SoC)
  - 5 GHz          : Qualcomm Atheros QCA9882
- Ethernet         : 2x 10/100/1000 Mbps
  - phy ("PD")     : Atheros AR8035
  - phy ("PSE")    : Atheros AR8033
- LEDs/keys (GPIO) : 3x/3x
- UART             : 1x RJ-45 port
  - "SERVICE"      : TTL (3.3V)
    - port         : ttyS0
    - assignment   : 1:3.3V, 2:GND, 3:TX, 4:RX
    - settings     : 115200n8
    - note         : no compatibility with "Cisco console cable"
- Buzzer           : 1x GPIO-controlled
- USB              : 1x USB 2.0 Type-A
- Power            : DC jack or PoE
  - DC jack        : 12 VDC, 1 A (device only, rating)
  - PoE            : 802.3af/at, 48 VDC, 0.25 A (device only, rating)
  - note           : supports 802.3af supply on PSE (downstream) port
                     when powered by DC adapter or 802.3at PoE

Flash instruction using factory.bin image:

1. Boot WAB-S1167-PS without no upstream connection (or PoE connection
   without DHCP)
2. Access to the WebUI ("http://192.168.3.1") on the device and open
   firmware update page
   ("ツールボックス" -> "ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update
   ("アップデート") button
4. Wait ~120 seconds to complete flashing

Revert to OEM firmware:

1. Download the latest OEM firmware
2. Remove 128 bytes(0x80) header from firmware image
3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val)
4. Upload the decoded firmware to the device
5. Flash to "firmware" partition by mtd command
6. Reboot

Notes:

- To use the "SERVICE" port, the connection of 3.3V line is also
  required to enable console output.
  The uart line of "SERVICE" is branched out from the internal pin
  header with 74HC126D and 3.3V line is connected to OE pin on it.

- The same PCB is used with WAB-S600-PS.

- To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC
  3.5 A adapter is recommended. (official: WAB-EX-ADP1)

MAC addresses:

Ethernet (PD, PSE): 00:90:FE:xx:xx:04 (Config, ethaddr (text))
2.4GHz            : 00:90:FE:xx:xx:04 (Config, ethaddr (text))
5GHz              : 00:90:FE:xx:xx:05

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-03-02 14:08:08 +01:00
INAGAKI Hiroshi 2791ee79fa ath79: add support for ELECOM WAB-S600-PS
ELECOM WAB-S600-PS is a 2.4/5 GHz band 11n (Wi-Fi 4) access point, based
on QCA9557.
This device also supports 11ac (Wi-Fi 5) with the another official
firmware.

Specification:

- SoC              : Qualcomm Atheros QCA9557
- RAM              : DDR2 128 MiB (2x Winbond W9751G6KB251)
- Flash            : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G)
- WLAN             : 2.4/5 GHz 2T2R
  - 2.4 GHz        : Qualcomm Atheros QCA9557 (SoC)
  - 5 GHz          : Qualcomm Atheros QCA9882
- Ethernet         : 2x 10/100/1000 Mbps
  - phy ("PD")     : Atheros AR8035
  - phy ("PSE")    : Atheros AR8033
- LEDs/keys (GPIO) : 3x/3x
- UART             : 1x RJ-45 port
  - "SERVICE"      : TTL (3.3V)
    - port         : ttyS0
    - assignment   : 1:3.3V, 2:GND, 3:TX, 4:RX
    - settings     : 115200n8
    - note         : no compatibility with "Cisco console cable"
- Buzzer           : 1x GPIO-controlled
- USB              : 1x USB 2.0 Type-A
- Power            : DC jack or PoE
  - DC jack        : 12 VDC, 1 A (device only, rating)
  - PoE            : 802.3af/at, 48 VDC, 0.25 A (device only, rating)
  - note           : supports 802.3af supply on PSE (downstream) port
                     when powered by DC adapter or 802.3at PoE

Flash instruction using factory.bin image:

1. Boot WAB-S600-PS without no upstream connection (or PoE connection
   without DHCP)
2. Access to the WebUI ("http://192.168.3.1") on the device and open
   firmware update page
   ("ツールボックス" -> "ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update
   ("アップデート") button
4. Wait ~120 seconds to complete flashing

Revert to OEM firmware:

1. Download the latest OEM firmware
2. Remove 128 bytes(0x80) header from firmware image
3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val)
4. Upload the decoded firmware to the device
5. Flash to "firmware" partition by mtd command
6. Reboot

Notes:

- To use the "SERVICE" port, the connection of 3.3V line is also
  required to enable console output.
  The uart line of "SERVICE" is branched out from the internal pin
  header with 74HC126D and 3.3V line is connected to OE pin on it.

- The same PCB is used with WAB-S1167-PS.

- To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC
  3.5 A adapter is recommended. (official: WAB-EX-ADP1)

MAC addresses:

Ethernet (PD, PSE): BC:5C:4C:xx:xx:7C (Config, ethaddr (text))
2.4GHz            : BC:5C:4C:xx:xx:7C (Config, ethaddr (text))
5GHz              : BC:5C:4C:xx:xx:7D

[original work of common dtsi part for WAB-I1750-PS]
Signed-off-by: Yanase Yuki <dev@zpc.st>
[adding support for WAB-S600-PS]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-03-02 14:08:08 +01:00
David Bentham f5b2b08190 ramips: Unielec u7621-01: remove invalid led status
The original commit had an invalid setting of the
led status for this device.

There is no gpio pin connected to that led so lets
remove these from the u7621-01 dtsi file.

Signed-off-by: David Bentham <db260179@gmail.com>
2024-03-02 14:08:08 +01:00
Tim Harvey c2e32b4886 octeontx: update default network config
Update the default network configuration for Gateworks Newport boards
such that the left-most front-panel NIC is WAN and any additional are in
LAN bridge:
 - gw610x/gw6903; single NIC: eth0
 - gw620x/gw630x; two NIC's from left to right are: eth1 eth0
 - gw640x; multiple NIC's from left to right: eth4 eth0 eth1 eth2 eth3

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2024-03-02 14:08:08 +01:00
Christian Lamparter 8b0407d15d apm821xx: MBL DUO-only: enable USB-Storage for boot from USB support
it is possible to boot and run OpenWrt from an image on an USB-Stick
on the MyBook Live DUO. (No, the MyBook Live Single does NOT have an
USB-Port and attempts at enabling it sadly all failed... so far).

To do that:
First, prepare a USB-Stick by writing the raw and uncompressed OpenWRT
factory image for the device onto the stick (i.e.
 # gunzip -c openwrt-*wd_mybooklive*-factory.img.gz > /dev/sd$XX).

Then enter the u-boot via an attached TTL/CMOS 3.3V cable adapter and
give the following commands a try in the:

 usb start; sata init
 ext2load usb 0:1 ${fdt_addr_r} /boot/apollo3g.dtb
 ext2load usb 0:1 ${kernel_addr_r} /boot/uImage
 setenv bootargs 'root=/dev/sdc2 rw rootfstype=squashfs,ext4 rootdelay=5'
 run addtty; bootm ${kernel_addr_r} - ${fdt_addr_r}

Notes:
 - booting from USB-Sticks takes a long time! Be prepared to wait a few
   minutes. (~3 minutes for 4 MiB /boot/uImage file on a USB 2.0 Stick)

 - the bootargs part 'root=/dev/sdX2' depends on how many HDDs/SSDs are
   slotted in. (if none: then use sda, if one: sdb. if two: sdc)

 - rootdelay is important as the storage on the USB-Sticks do not show
   up fast enough. 5 seconds might be excessive though.

 - it's possible to concat these commands together in one line and
   write it into u-boot's "bootcmd" environment variable and save the
   environment to make the device to always boot from USB from then on.

   if you have accidentally overridden the 'bootcmd' and want to return
   to 'spec' enter the following commands :

   setenv bootcmd 'run boot_sata_script_ap2nc'
   saveenv

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2024-03-02 14:08:07 +01:00
Christian Lamparter 7e53473ee8 apm821xx: add u-boot,env compatible
Note about the MyBook Live.
The MyBook Live didn't have the encompassing fixed-partitions.
This is needed for the u-boot,env compatible to be read as otherwise
the kernel assumes this is a legacy NOR/NAND node and this binding
is unsupported.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2024-03-02 14:08:04 +01:00
Christian Lamparter 625dea6170 apm821xx: remove 5.15 remnants
deletes config-5.15 and patches-5.15/.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2024-03-02 14:08:00 +01:00
Christian Lamparter d775dc74ee apm821xx: make 6.1 kernel default
6.1 has been available for some time for testing.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2024-03-02 14:07:59 +01:00
Robert Marko 7f13b9f8be qualcommax: enable DEBUG_BUGVERBOSE
Enable DEBUG_BUGVERBOSE by default on qualcommax as without it once BUG()
is called we will not get any output other than
"------------[ cut here ]------------"
which is not usefull at all, so since we dont have kernel size constraints
lets enable it by default.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-03-01 19:51:24 +01:00
Eneas U de Queiroz 65a3eb28d5 build: scripts/config - update to kconfig-v6.6.16
The main goal here is to keep this close to upstream.

Changes include:
 - allow symbols implied by y to become m
 - make 'imply' obey the direct dependency
 - allow only 'config', 'comment', and 'if' inside 'choice'
 - qconf: make search fully work again on split mode
 - qconf: navigate menus on hyperlinks
 - remove '---help---' support
 - qconf: allow to edit "int", "hex", "string" menus in-place
 - qconf: drop Qt4 support
 - nconf: fix core dump when searching in empty menu
 - nconf: stop endless search loops
 - Create links to main menu items in search
 - fix segmentation fault in menuconfig search
 - nconf: Add search jump feature
 - port qconf to work with Qt6 in addition to Qt5
 - fix possible buffer overflow
 - fix memory leak from range properties

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2024-03-01 19:02:00 +01:00
Pawel Dembicki ff6df9ac9f layerscape: remove 5.15 kernel support
Kernel was switched to 6.1. Lets drop 5.15 support.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2024-03-01 18:29:09 +01:00
Pawel Dembicki 73f99b6849 layerscape: switch kernel to 6.1 version
It was testing since couple months. Lets switch it to 6.1 by default for
wide testing.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2024-03-01 18:29:09 +01:00
Cedric DOURLENT 84331215e5 build: fix kernel component in CycloneDX SBOM
As stated in the cycloneDX documentation, the field "type" is mandatory for all components.

More details here (https://cyclonedx.org/docs/1.5/json/#components_items_type)

Signed-off-by: Cedric DOURLENT <cedric.dourlent@softathome.com>
2024-03-01 16:42:34 +01:00
Daniel Golle a86ff06d2e mediatek: mt7622: rtl8367c: add casts to fix compiler warnings
Use type casts to prevent compiler warnings which are going to turn
into errors when we switch to Linux 6.6.
In the long run we should try to get rid of this downstream driver
now that RTL8367S is support by the rtl8365mb DSA driver.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-03-01 01:42:36 +00:00
Daniel Golle 7c468e5e64 mediatek: rename or replace accepted patches
Rename kernel patches accepted upstream to indicate at which version
they have been accepted, replacing downstream variants which what was
accepted upstream. Note that some of them are fixes which will
find their way to older kernel versions as well via linux-stable.
No functional changes.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-03-01 01:42:36 +00:00
Daniel Golle 9d7e603f4d mediatek: fix version tag in thermal patches
Some backported thermal patches ended up with the wrong kernel
version in their filename. Fix this.

Fixes: c36de2e73a ("mediatek: backport a hell of thermal commits")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-03-01 01:03:42 +00:00
Daniel Golle f08e63bd83 uboot-mediatek: remove rootfs_data before attempting to replace fip
Make sure there is enough space to replace 'fip' volume and always
remove rootfs_data before.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-03-01 00:59:49 +00:00
Linus Walleij ef34f8f5b5 kirkwood: Add Marvell RTC to all machines with nothing else
The Kirkwood SoCs all have an onchip RTC that can hold the time
over e.g. a reboot which will help if no NTP servers are available.

Create a kernel module package for the Marvell RTC, and add it to
all Kirkwood devices that do not have their own discrete
battery-backed RTC. Adding it to platforms with a proper RTC
is just surplus.

All Kirkwoods have at least one RTC so add RTC to the features
list for Kirkwood as well.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2024-02-29 23:01:38 +01:00