Currently PHY information obtained from "iw phy" lacks information about
a PHYs HE capabilities when using the by default installed iw-tiny.
As there are already 802.11ax supported devices, enabled printing this
information for the by-default installed iw variant.
Signed-off-by: David Bauer <mail@david-bauer.net>
BCM4906, BCM4908 and BCM49408 are SoCs with 64 bit ARMv8 B53 CPUs.
Upstream Linux is slowly getting support for that SoCs family so it
makes sense to add target for it.
This prepares initial support for:
1. Asus GT-AC5300
BCM4908 based device (4 CPUs) with 1024 MiB RAM, NAND, 8 LAN ports.
2. Netgear R8000P
BCM4906 based device (2 CPUs) with 512 MiB RAM, NAND, 4 LAN ports.
Flashing info will come later as we learn how to generate proper images.
It isn't usable yet (it only produces a bootable kernel) so "source-only"
is used.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Enable the ability to use segment routing based on IPv6. It allows the
packet to specify a path that the packet should take through the
network.
Lwtunnel allow an easy encapsulation of a package. You can just install
ip-full package and use it:
ip -6 route add 2003::/64 dev eth0 encap seg6 mode encap \
segs 2001::1,2002::2
An IPv6 package looks like this:
[IPv6 HDR][IPv6 RH][IPv6 HDR][Data...]
Netifd support:
https://git.openwrt.org/?p=project/netifd.git;
a=commit;h=458b1a7e9473c150a40cae5d8be174f4bb03bd39
Increases imagesize by 24.125 KiB. Therefore, only enable for devices
with enough flash.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Previously, ccache would end up using the system libzstd, which is not
supposed to be a build requirement.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
When compiling with CONFIG_ALL_KMODS enabled, compilation might stall
due to unset rockchip-specific config symbols. Disable these to avoid
stalling this step.
Signed-off-by: David Bauer <mail@david-bauer.net>
Instead of using an ancient qemu version in-tree the building machine
should just have qemu-utils installed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Currently `qemu-img` is used to convert raw x86 images to VDI and VMDK
images, used for virtual machines.
Having `qemu-img` in tree requires us to maintain an ancient version of
`qemu-utils`, which recently required extra work to compile with newer
compiler version.
This commit prints a warning message in case `qemu-img` is missing.
As a next step the in-tree version of `qemu-img` can be removed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
To simplify the way netifd acquires the PIDs of wpa_supplicant and
hostapd let the config_add method of both of them return the PID of the
called process. Use the returned PID instead of querying procd when
adding wpa_supplicant configuration.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Linux 5.9 introduces support for ZSTD ramdisk and initrd compression,
make sure we enable/disable the relevant options when building an
initramfs enabled kernel.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
When we use an external kernel tree which may not have been fully
cleaned, there may be user_headers left which do not match the target
architecture, leading to build failures for packages that do an explicit
inclusion of user_headers (such as iproute2 or iptables). Make sure we
delete them while preparing the directory.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The ZyXEL GS1900-8HP is an 8 port gigabit switch with PoE+ support.
There are two versions on the market (v1 & v2) which share similar
specs (same flash size and flash layout, same RAM size, same PoE+ power
envelope) but have a different case and board layout that they each
share with other GS1900 siblings.
The v1 seems to share its PCB and case with non-PoE GS1900-8; as such,
adding support for the GS1900-8 would probably be trivial. The v2 seems
to share its casing and platform with its already supported bigger
brother, the GS1900-10HP - its board looks the same, except for two
holes where the GS1900-10 has its SFP ports.
Like their 10 port sibling, both devices have a dual firmware layout.
Both GS1900-8HP boards have the same 70W PoE+ power budget. In order to
manipulate the PoE+, one needs the rtl83xx-poe package [1].
After careful consideration it was decided to go with separate images
for each version.
Specifications (v1)
-------------------
* SoC: Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash: Macronix MX25L12835F 16 MiB
* RAM: Nanya NT5TU128M8HE-AC 128 MiB DDR2 SDRAM
* Ethernet: 8x 10/100/1000 Mbit
* PoE+: Broadcom BCM59111KMLG (IEEE 802.3at-2009 compliant, 2x)
* UART: 1 serial header with populated standard pin connector on the
left side of the PCB, towards the bottom. Pins are labeled:
+ VCC (3.3V)
+ TX
+ RX
+ GND
Specifications (v2)
-------------------
* SoC: Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash: Macronix MX25L12835F 16 MiB
* RAM: Samsung K4B1G0846G 128 MiB DDR3 SDRAM
* Ethernet: 8x 10/100/1000 Mbit
* PoE+: Broadcom BCM59121B0KMLG (IEEE 802.3at-2009 compliant)
* UART: 1 angled serial header with populated standard pin connector
accessible from outside through the ventilation slits on the
side. Pins from top to bottom are clearly marked on the PCB:
+ VCC (3.3V)
+ TX
+ RX
+ GND
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
Instructions are identical to those for the GS1900-10HP and apply both
to the GS1900-8HP v1 and v2 as well.
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-10HP is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only boot off the first partition anyway (hardcoded in the DTS). To
make sure we are manipulating the first partition, issue the following
commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8hp-v{1,2}-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp//tmp/openwrt-realtek-generic-zyxel_gs1900-8hp-v{1,2}-squashfs-sysupgrade.bin
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[merge PoE case, keep device definitions separate, change all those
hashes in the commit message to something else so they don't get
removed when changing the commit ...]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The ZyXEL GS1900-8HP v1, v2 and GS1900-10HP are all built on a similar
Realtek RTL8380M platform. Create a common DTSI in preparation for
GS1900-8HP support, and switch to the macros defined in rtl838x.dtsi.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[drop redundant includes, use &mdio directly, do not replace SFP
ports]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds kernel module for Silicon Labs CP2112 HID USB to SMBus
Master Bridge. This is a HID device driver which registers as an i2c
adapter and gpiochip to expose these functions of the CP2112.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Remove trailing whitespaces in two *.mk files.
Signed-off-by: Leon M. George <leon@georgemail.eu>
[fix title, add message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ZyXEL spells its own name all uppercase with just the Y lowercase. Adapt
the realtek target to follow this (other OpenWrt targets already do so).
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Move the memory out of the rtl838x.dtsi and into the device family DTSI
or device DTS if applicable. This aligns with upstream practice.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[add missing block for dgs-1210-10p, move block below chosen node]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The identifier is already present in rtl838x.dtsi, and adding it
twice is not only redundant but actually wrong.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
While the speed improvement might be negligible, there is still no
reason to read individual bytes.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For:
- ENH202 v1
- ENS202EXT v1
These boards were committed before it was discovered
that for all Engenius boards with a "failsafe" image,
forcing the failsafe image to load next boot
can be achieved by editing the u-boot environment like:
`fw_setenv rootfs_checksum 0`
So it's not necessary to delete a partition to boot to failsafe image.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This moves some of the Engenius boards from generic to tiny:
- EAP350 v1
- ECB350 v1
- ENH202 v1
For these, factory.bin builds are already failing on master
branch because of the unique situation for these boards:
- 8 MB flash
- an extra "failsafe" image for recovery
- TFTP does not work (barely possible with 600 MTU)
- bootloader loads image from a longer flash offset
- 1 eraseblock each needed for OKLI kernel loader and fake rootfs
- using mtd-concat to make use of remaining space...
The manual alternative would be removing the failsafe partition.
However this comes with the risk of extremely difficult recovery
if a flash ever fails because TFTP on the bootloader is bugged.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
[improve commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
imx6 has it's own pcie host driver so we do
not need the one from DW.
This fixes following boot error:
[ 0.156913] dw-pcie 1ffc000.pcie: IRQ index 1 not found
Fixes: 6d5291ff72 ("imx6: add support for kernel 5.4")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 regulator descriptions carry identical naming.
This leads to following boot warning:
[ 0.173138] debugfs: Directory 'vdd1p8' with parent 'regulator' already present!
Fix this by renaming the one used for audio.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
cmake is a dependency of ccache, which means it is build before ccache
is available and hence must be build with non-ccache CC and CXX. It
currently works, because the cmake build system splits the compiler
variable and treats them as multiple compilers to check.
For "ccache gcc" it first tests for "ccache", which always fails,
because ccache is not a compiler by itself, even if it is available, and
then ends up calling "gcc" alone, effectively never using ccache.
Let's make this explicit by forcing the use of non-ccache CC and CXX.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
For glibc, lua needs an explicit link to libdl as glibc has it separate
Fixes the following error in at least collectd:
ld: usr/lib/liblua.so: undefined reference to `dlopen'
ld: usr/lib/liblua.so: undefined reference to `dlclose'
ld: usr/lib/liblua.so: undefined reference to `dlerror'
ld: usr/lib/liblua.so: undefined reference to `dlsym'
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This keeps the configuration, like the size of the cache, and the
statistics intact. Move the removal of the cache directory to the
distclean target, but only delete the .ccache directory inside of our
build tree, as we should not mess with a user-configured external ccache
directory this destructively.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
fd017ba iwinfo: add ht and vht operation info to wifi scan
4c66b31 iwinfo: export center channel for info ubus call
e28d4a5 iwinfo: add support for 802.11ad and GCMP
5c15f57 iwinfo: return hwmode 'ad' on 802.11ad-only hardware
ea7f471 iwinfo: include ht_operation data only if available
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
- Encode ABI version in compiled shared object file
- Only ship versioned shared library
a17f561 iwinfo: detect QCA IPQ4019 WiSoC from FDT
ea28dfb iwinfo: export ht and vht operation in scan results
4e22953 iwinfo: export center_chan info for local wifi
74d13fb cli: account for additional digit for frequencies above 10GHz
8bfd8d8 iwinfo: add support for GCMP cipher
618c1e8 iwinfo: add hardware description for QCA MIPS WiSoCs
0702f32 iwinfo: improve center channel handling
51c1336 iwinfo: set center chan unsupported for not-nl80211 driver
23d2722 build: add ability to specify shared object version
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The recent 7f285d "scripts/feeds: warn when skipping core package
override" floods SDK output with warning of overwriting "linux" and
"toolchain" core packages. This should be ignored as these are not
regular packages added via feeds.
While at it slightly improve the warning string.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Strictly, an SPDX identifier requires a space between the comment
marker and the identifier itself. This has been addressed in
b69c21738e ("treewide: add space before SPDX identifier"), but
some new malformatted identifiers were merged recently.
This could have been prevented by using checkpatch.pl earlier.
Fixes: 1a775a4fd0 ("ipq806x: add support for TP-Link Talon AD7200")
Fixes: 8ddaeaf642 ("ipq806x: create DTSI for TP-Link AD7200 and C2600")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The TP-Link AD7200 appears with and without the "Talon" model name
prefix. Let's use both variants for 'make menuconfig' so everybody
can locate the device.
Concerning the revision, the TP-Link page lists v1 and v2 with the
device currently marked as "End of Life". However, the v2 and latest
v1 firmware are byte-identical. Thus, we only need one image for
this device and do not need to include the revision in the image name.
While at it, remove the useless BOARD_NAME variable which only makes
sense in combination with upgrade from legacy stable versions or when
custom upgrade scripts are involved.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Both devices share most of their setup except buttons and LEDs,
so having a common DTSI removes a lot of duplicate code.
In order to have a shared partitioning scheme, device-id and
product-info from AD7200 have been merged into a single
product-info partition like for C2600.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This does several cosmetic adjustments for AD7200's DTS:
- Make node name, DT label and label property consistent
- Drop wrong and unused spi4 label
- Use generic flash@0 node name
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit f1620630e9.
This update introduces potentially remote exploitable buffer overreads
in IE parsing logic.
It also breaks the ABI without introdcing SOVERSION library versioning.
Furthermore, HT information is incorrectly added for non-HT BSSes.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This reverts commit 190e793963.
This update introduces a potential null-pointer deref with subsequent rpcd
crash when querying wireless info for non-nl80211 wdevs.
Additionally it wrongly includes ht frequency information for non-ht BSSes.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The MT7915 radio currently advertises 2.4GHz channels while the antenna
path only supports 5 GHz. Limit the radio to 5GHz channels to prevent
users from configuring non-supported channels.
Signed-off-by: David Bauer <mail@david-bauer.net>
fd017ba iwinfo: add ht and vht operation info to wifi scan
4c66b31 iwinfo: export center channel for info ubus call
e28d4a5 iwinfo: add support for 802.11ad and GCMP
5c15f57 iwinfo: return hwmode 'ad' on 802.11ad-only hardware
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
a17f561 iwinfo: detect QCA IPQ4019 WiSoC from FDT
ea28dfb iwinfo: export ht and vht operation in scan results
4e22953 iwinfo: export center_chan info for local wifi
74d13fb cli: account for additional digit for frequencies above 10GHz
8bfd8d8 iwinfo: add support for GCMP cipher
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This fixes the build problems for the REALTEK target by adding a proper
configuration option for the phy module.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
use PKG_FIXUP:=autoreconf to generate configure
200-hide-dlsym-error.patch deleted due to fixed upstream in another way
other patches refreshed to reflect latest changes
Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
