mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2024-06-13 10:49:13 +02:00
mvebu: cortexa9: Add support for Ctera C200-V2
2-Bay NAS - maximum two 3.5" Harddisks Hardware: - SoC: Marvell 88F6707-A1 ARMv7 Processor 1,2GHz (ARMADA 370 SoC) - Ram: 1GB (2x Nanya NT5CC512M8DN-D1) - NAND Flash: 256MB (ESMT F59L2G81A-25T) - Lan: 1x GBE (Marvell 88E1318-NNB2) - Storage: 2x SATA HDD 3.5" Slot - USB: 2x USB 3.0 port (Renesas uPD720202) - Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND) - LEDs: 13x GPIO controlled - Buttons: 2x GPIO controlled Known issues: - Buzzer is unused due lack of proper driver - USB1/2 usbport ledtrigger won't work (through DT) - Renesas uPD720202 requires firmware file. It's possible to find non-free binary. Please look for 'UPDATE.mem' file and put in into '/lib/firmware/renesas_usb_fw.mem' file. Installation: - Apply factory initramfs image via stock web-gui. - Do sysupgrade to make installation complete. Back to stock: - OpenWrt rootfs partition use unused space after stock firmware. - Full revert is possible. - Login via ssh and run: ## ctera_c200-v2_back_to_factory start ## . /lib/functions.sh part=$(find_mtd_part "active_bank") active_bank=$(strings "$part" | grep bank) if [ "$active_bank" = "bank1" ]; then echo "bank2" > /tmp/change_bank else echo "bank1" > /tmp/change_bank fi mtd write /tmp/change_bank active_bank reboot ## ctera_c200-v2_back_to_factory end ## Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> (put back-to-stock script into commit message, removed dup. SUBPAGESIZE var, added 01_leds for non-working dt-usb-port trigger) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit is contained in:
parent
1ed50b92d1
commit
9149ed4f05
|
@ -1712,7 +1712,8 @@ define KernelPackage/usb3
|
||||||
+TARGET_bcm53xx:kmod-usb-bcma \
|
+TARGET_bcm53xx:kmod-usb-bcma \
|
||||||
+TARGET_bcm53xx:kmod-phy-bcm-ns-usb3 \
|
+TARGET_bcm53xx:kmod-phy-bcm-ns-usb3 \
|
||||||
+TARGET_ramips_mt7621:kmod-usb-xhci-mtk \
|
+TARGET_ramips_mt7621:kmod-usb-xhci-mtk \
|
||||||
+(TARGET_apm821xx_nand&&LINUX_5_10):kmod-usb-xhci-pci-renesas
|
+(TARGET_apm821xx_nand&&LINUX_5_10):kmod-usb-xhci-pci-renesas \
|
||||||
|
+TARGET_mvebu_cortexa9:kmod-usb-xhci-pci-renesas
|
||||||
KCONFIG:= \
|
KCONFIG:= \
|
||||||
CONFIG_USB_PCI=y \
|
CONFIG_USB_PCI=y \
|
||||||
CONFIG_USB_XHCI_PCI \
|
CONFIG_USB_XHCI_PCI \
|
||||||
|
|
|
@ -337,6 +337,9 @@ CONFIG_PJ4B_ERRATA_4742=y
|
||||||
CONFIG_PL310_ERRATA_753970=y
|
CONFIG_PL310_ERRATA_753970=y
|
||||||
CONFIG_PLAT_ORION=y
|
CONFIG_PLAT_ORION=y
|
||||||
CONFIG_PM_OPP=y
|
CONFIG_PM_OPP=y
|
||||||
|
CONFIG_POWER_RESET=y
|
||||||
|
CONFIG_POWER_RESET_GPIO=y
|
||||||
|
# CONFIG_POWER_RESET_QNAP is not set
|
||||||
CONFIG_PRINTK_SAFE_LOG_BUF_SHIFT=11
|
CONFIG_PRINTK_SAFE_LOG_BUF_SHIFT=11
|
||||||
CONFIG_PWM=y
|
CONFIG_PWM=y
|
||||||
CONFIG_PWM_SYSFS=y
|
CONFIG_PWM_SYSFS=y
|
||||||
|
|
|
@ -11,6 +11,10 @@ board=$(board_name)
|
||||||
boardname="${board##*,}"
|
boardname="${board##*,}"
|
||||||
|
|
||||||
case "$board" in
|
case "$board" in
|
||||||
|
ctera,c200-v2
|
||||||
|
ucidef_set_led_usbport "usb2" "USB2" "green:usb-2" "usb1-port1" "usb2-port1"
|
||||||
|
ucidef_set_led_usbport "usb3" "USB3" "green:usb-1" "usb1-port2" "usb2-port2"
|
||||||
|
;;
|
||||||
kobol,helios4)
|
kobol,helios4)
|
||||||
ucidef_set_led_usbport "USB" "USB" "helios4:green:usb" "usb1-port1" "usb2-port1" "usb3-port1" "usb4-port1" "usb5-port1"
|
ucidef_set_led_usbport "USB" "USB" "helios4:green:usb" "usb1-port1" "usb2-port1" "usb3-port1" "usb4-port1" "usb5-port1"
|
||||||
;;
|
;;
|
||||||
|
|
|
@ -12,6 +12,9 @@ mvebu_setup_interfaces()
|
||||||
local board="$1"
|
local board="$1"
|
||||||
|
|
||||||
case "$board" in
|
case "$board" in
|
||||||
|
ctera,c200-v2)
|
||||||
|
ucidef_set_interface_lan "eth0" "dhcp"
|
||||||
|
;;
|
||||||
cznic,turris-omnia)
|
cznic,turris-omnia)
|
||||||
ucidef_set_interfaces_lan_wan "lan0 lan1 lan2 lan3 lan4" "eth2"
|
ucidef_set_interfaces_lan_wan "lan0 lan1 lan2 lan3 lan4" "eth2"
|
||||||
;;
|
;;
|
||||||
|
@ -58,6 +61,10 @@ mvebu_setup_macs()
|
||||||
buffalo,ls421de)
|
buffalo,ls421de)
|
||||||
lan_mac=$(mtd_get_mac_ascii u-boot-env eth1addr)
|
lan_mac=$(mtd_get_mac_ascii u-boot-env eth1addr)
|
||||||
;;
|
;;
|
||||||
|
ctera,c200-v2)
|
||||||
|
label_mac=$(mtd_get_mac_ascii dev_params mac)
|
||||||
|
lan_mac=$label_mac
|
||||||
|
;;
|
||||||
linksys,wrt1200ac|\
|
linksys,wrt1200ac|\
|
||||||
linksys,wrt1900ac-v2|\
|
linksys,wrt1900ac-v2|\
|
||||||
linksys,wrt1900acs|\
|
linksys,wrt1900acs|\
|
||||||
|
|
|
@ -3,7 +3,7 @@
|
||||||
# Copyright (C) 2016 LEDE-Project.org
|
# Copyright (C) 2016 LEDE-Project.org
|
||||||
#
|
#
|
||||||
|
|
||||||
RAMFS_COPY_BIN='fw_printenv fw_setenv'
|
RAMFS_COPY_BIN='fw_printenv fw_setenv strings'
|
||||||
RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
|
RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
|
||||||
REQUIRE_IMAGE_METADATA=1
|
REQUIRE_IMAGE_METADATA=1
|
||||||
|
|
||||||
|
@ -26,6 +26,17 @@ platform_do_upgrade() {
|
||||||
buffalo,ls421de)
|
buffalo,ls421de)
|
||||||
nand_do_upgrade "$1"
|
nand_do_upgrade "$1"
|
||||||
;;
|
;;
|
||||||
|
ctera,c200-v2)
|
||||||
|
part=$(find_mtd_part "active_bank")
|
||||||
|
|
||||||
|
if [ -n "$part" ]; then
|
||||||
|
CI_KERNPART="$(strings $part | grep bank)"
|
||||||
|
nand_do_upgrade "$1"
|
||||||
|
else
|
||||||
|
echo "active_bank partition missed!"
|
||||||
|
return 1
|
||||||
|
fi
|
||||||
|
;;
|
||||||
cznic,turris-omnia|\
|
cznic,turris-omnia|\
|
||||||
kobol,helios4|\
|
kobol,helios4|\
|
||||||
solidrun,clearfog-base-a1|\
|
solidrun,clearfog-base-a1|\
|
||||||
|
|
|
@ -0,0 +1,426 @@
|
||||||
|
// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
|
||||||
|
/*
|
||||||
|
* Device Tree file for Ctera C200-V2
|
||||||
|
*
|
||||||
|
* Copyright (C) 2021 Pawel Dembicki <paweldembicki@gmail.com>
|
||||||
|
*/
|
||||||
|
|
||||||
|
/dts-v1/;
|
||||||
|
|
||||||
|
#include "armada-370.dtsi"
|
||||||
|
#include <dt-bindings/gpio/gpio.h>
|
||||||
|
#include <dt-bindings/input/input.h>
|
||||||
|
#include <dt-bindings/thermal/thermal.h>
|
||||||
|
#include <dt-bindings/leds/common.h>
|
||||||
|
|
||||||
|
/ {
|
||||||
|
model = "Ctera C200 V2";
|
||||||
|
compatible = "ctera,c200-v2", "marvell,armada370", "marvell,armada-370-xp";
|
||||||
|
|
||||||
|
aliases {
|
||||||
|
led-boot = &led_status_green;
|
||||||
|
led-failsafe = &led_status_red;
|
||||||
|
led-running = &led_status_green;
|
||||||
|
led-upgrade = &led_status_red;
|
||||||
|
};
|
||||||
|
|
||||||
|
chosen {
|
||||||
|
bootargs = "console=ttyS0,115200";
|
||||||
|
stdout-path = "serial0:115200n8";
|
||||||
|
};
|
||||||
|
|
||||||
|
memory {
|
||||||
|
device_type = "memory";
|
||||||
|
reg = <0x00000000 0x40000000>; /* 1024 MB */
|
||||||
|
};
|
||||||
|
|
||||||
|
soc {
|
||||||
|
ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
|
||||||
|
MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000
|
||||||
|
MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>;
|
||||||
|
};
|
||||||
|
|
||||||
|
thermal-zones {
|
||||||
|
ethphy-thermal {
|
||||||
|
polling-delay = <20000>;
|
||||||
|
polling-delay-passive = <2000>;
|
||||||
|
|
||||||
|
thermal-sensors = <ðphy0>;
|
||||||
|
|
||||||
|
trips {
|
||||||
|
ethphy_alert1: trip1 {
|
||||||
|
temperature = <65000>;
|
||||||
|
hysteresis = <4000>;
|
||||||
|
type = "passive";
|
||||||
|
};
|
||||||
|
|
||||||
|
ethphy_crit: trip2 {
|
||||||
|
temperature = <100000>;
|
||||||
|
hysteresis = <2000>;
|
||||||
|
type = "critical";
|
||||||
|
};
|
||||||
|
};
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
keys {
|
||||||
|
compatible = "gpio-keys";
|
||||||
|
pinctrl-0 = <&pmx_buttons>;
|
||||||
|
pinctrl-names = "default";
|
||||||
|
|
||||||
|
power {
|
||||||
|
label = "Power Button";
|
||||||
|
linux,code = <KEY_POWER>;
|
||||||
|
gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>;
|
||||||
|
};
|
||||||
|
|
||||||
|
reset {
|
||||||
|
label = "Reset Button";
|
||||||
|
linux,code = <KEY_RESTART>;
|
||||||
|
gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
|
||||||
|
};
|
||||||
|
|
||||||
|
usb1 {
|
||||||
|
label = "USB1 Button";
|
||||||
|
linux,code = <BTN_0>;
|
||||||
|
gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
|
||||||
|
};
|
||||||
|
|
||||||
|
usb2 {
|
||||||
|
label = "USB2 Button";
|
||||||
|
linux,code = <BTN_1>;
|
||||||
|
gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
gpio-poweroff {
|
||||||
|
compatible = "gpio-poweroff";
|
||||||
|
pinctrl-0 = <&pmx_poweroff>;
|
||||||
|
pinctrl-names = "default";
|
||||||
|
gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
|
||||||
|
};
|
||||||
|
|
||||||
|
leds {
|
||||||
|
compatible = "gpio-leds";
|
||||||
|
pinctrl-0 = <&pmx_leds1 &pmx_leds2>;
|
||||||
|
pinctrl-names = "default";
|
||||||
|
|
||||||
|
led-0 {
|
||||||
|
function = LED_FUNCTION_USB;
|
||||||
|
function-enumerator = <2>;
|
||||||
|
color = <LED_COLOR_ID_RED>;
|
||||||
|
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
|
||||||
|
};
|
||||||
|
|
||||||
|
led-1 {
|
||||||
|
function = LED_FUNCTION_USB;
|
||||||
|
function-enumerator = <2>;
|
||||||
|
color = <LED_COLOR_ID_GREEN>;
|
||||||
|
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
|
||||||
|
linux,default-trigger = "usbport";
|
||||||
|
trigger-sources = <&usb1_port 1>, <&usb2_port 1>;
|
||||||
|
};
|
||||||
|
|
||||||
|
led-2 {
|
||||||
|
function = LED_FUNCTION_USB;
|
||||||
|
function-enumerator = <1>;
|
||||||
|
color = <LED_COLOR_ID_RED>;
|
||||||
|
gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
|
||||||
|
};
|
||||||
|
|
||||||
|
led-3 {
|
||||||
|
function = LED_FUNCTION_USB;
|
||||||
|
function-enumerator = <1>;
|
||||||
|
color = <LED_COLOR_ID_GREEN>;
|
||||||
|
gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
|
||||||
|
linux,default-trigger = "usbport";
|
||||||
|
trigger-sources = <&usb1_port 2>, <&usb2_port 2>;
|
||||||
|
};
|
||||||
|
|
||||||
|
led-4 {
|
||||||
|
function = LED_FUNCTION_DISK;
|
||||||
|
function-enumerator = <2>;
|
||||||
|
color = <LED_COLOR_ID_GREEN>;
|
||||||
|
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
|
||||||
|
linux,default-trigger = "ata2";
|
||||||
|
};
|
||||||
|
|
||||||
|
led-5 {
|
||||||
|
function = LED_FUNCTION_DISK;
|
||||||
|
function-enumerator = <1>;
|
||||||
|
color = <LED_COLOR_ID_RED>;
|
||||||
|
gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
|
||||||
|
};
|
||||||
|
|
||||||
|
led-6 {
|
||||||
|
function = LED_FUNCTION_DISK;
|
||||||
|
function-enumerator = <2>;
|
||||||
|
color = <LED_COLOR_ID_RED>;
|
||||||
|
gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
|
||||||
|
};
|
||||||
|
|
||||||
|
led-7 {
|
||||||
|
function = LED_FUNCTION_INDICATOR;
|
||||||
|
color = <LED_COLOR_ID_BLUE>;
|
||||||
|
gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
|
||||||
|
};
|
||||||
|
|
||||||
|
led-8 {
|
||||||
|
function = LED_FUNCTION_DISK_ERR;
|
||||||
|
color = <LED_COLOR_ID_RED>;
|
||||||
|
gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
|
||||||
|
};
|
||||||
|
|
||||||
|
led-9 {
|
||||||
|
function = LED_FUNCTION_DISK_ERR;
|
||||||
|
color = <LED_COLOR_ID_GREEN>;
|
||||||
|
gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
|
||||||
|
};
|
||||||
|
|
||||||
|
led_status_red: led-10 {
|
||||||
|
label = "red:status";
|
||||||
|
function = LED_FUNCTION_STATUS;
|
||||||
|
color = <LED_COLOR_ID_RED>;
|
||||||
|
gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
|
||||||
|
};
|
||||||
|
|
||||||
|
led-11 {
|
||||||
|
function = LED_FUNCTION_DISK;
|
||||||
|
function-enumerator = <1>;
|
||||||
|
color = <LED_COLOR_ID_GREEN>;
|
||||||
|
gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
|
||||||
|
linux,default-trigger = "ata1";
|
||||||
|
};
|
||||||
|
|
||||||
|
led_status_green: led-12 {
|
||||||
|
label = "green:status";
|
||||||
|
function = LED_FUNCTION_STATUS;
|
||||||
|
color = <LED_COLOR_ID_GREEN>;
|
||||||
|
gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
|
||||||
|
};
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
&coherencyfab {
|
||||||
|
broken-idle;
|
||||||
|
};
|
||||||
|
|
||||||
|
ð1 {
|
||||||
|
pinctrl-0 = <&ge1_rgmii_pins>;
|
||||||
|
pinctrl-names = "default";
|
||||||
|
status = "okay";
|
||||||
|
phy-handle = <ðphy0>;
|
||||||
|
phy-connection-type = "rgmii-id";
|
||||||
|
};
|
||||||
|
|
||||||
|
&i2c0 {
|
||||||
|
pinctrl-0 = <&i2c0_pins>;
|
||||||
|
pinctrl-names = "default";
|
||||||
|
clock-frequency = <100000>;
|
||||||
|
status = "okay";
|
||||||
|
|
||||||
|
hwmon@2a {
|
||||||
|
compatible = "nuvoton,nct7802";
|
||||||
|
reg = <0x2a>;
|
||||||
|
};
|
||||||
|
|
||||||
|
rtc@30 {
|
||||||
|
compatible = "sii,s35390a";
|
||||||
|
reg = <0x30>;
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
&mdio {
|
||||||
|
pinctrl-0 = <&mdio_pins>;
|
||||||
|
pinctrl-names = "default";
|
||||||
|
|
||||||
|
ethphy0: ethernet-phy@0 { /* Marvell 88E1318 */
|
||||||
|
reg = <0>;
|
||||||
|
#thermal-sensor-cells = <0>;
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
&nand_controller {
|
||||||
|
status = "okay";
|
||||||
|
|
||||||
|
nand@0 {
|
||||||
|
reg = <0>;
|
||||||
|
label = "pxa3xx_nand-0";
|
||||||
|
nand-rb = <0>;
|
||||||
|
marvell,nand-keep-config;
|
||||||
|
nand-on-flash-bbt;
|
||||||
|
nand-ecc-strength = <4>;
|
||||||
|
nand-ecc-step-size = <512>;
|
||||||
|
|
||||||
|
partitions {
|
||||||
|
compatible = "fixed-partitions";
|
||||||
|
#address-cells = <1>;
|
||||||
|
#size-cells = <1>;
|
||||||
|
|
||||||
|
partition@0 {
|
||||||
|
label = "uboot";
|
||||||
|
reg = <0x0000000 0x200000>;
|
||||||
|
read-only;
|
||||||
|
};
|
||||||
|
|
||||||
|
partition@200000 {
|
||||||
|
label = "certificate";
|
||||||
|
reg = <0x0200000 0x100000>;
|
||||||
|
read-only;
|
||||||
|
};
|
||||||
|
|
||||||
|
partition@300000 {
|
||||||
|
label = "preset_cfg";
|
||||||
|
reg = <0x0300000 0x100000>;
|
||||||
|
read-only;
|
||||||
|
};
|
||||||
|
|
||||||
|
partition@400000 {
|
||||||
|
label = "dev_params";
|
||||||
|
reg = <0x0400000 0x100000>;
|
||||||
|
read-only;
|
||||||
|
};
|
||||||
|
partition@500000 {
|
||||||
|
label = "active_bank";
|
||||||
|
reg = <0x0500000 0x0100000>;
|
||||||
|
};
|
||||||
|
|
||||||
|
partition@600000 {
|
||||||
|
label = "magic";
|
||||||
|
reg = <0x0600000 0x0100000>;
|
||||||
|
read-only;
|
||||||
|
};
|
||||||
|
|
||||||
|
partition@700000 {
|
||||||
|
label = "bank1";
|
||||||
|
reg = <0x0700000 0x2800000>;
|
||||||
|
};
|
||||||
|
|
||||||
|
partition@2f00000 {
|
||||||
|
label = "bank2";
|
||||||
|
reg = <0x2f00000 0x2800000>;
|
||||||
|
};
|
||||||
|
|
||||||
|
/* 0x5700000-0x5a00000 undefined in vendor firmware */
|
||||||
|
|
||||||
|
partition@5a00000 {
|
||||||
|
label = "reserved";
|
||||||
|
reg = <0x5a00000 0x2000000>;
|
||||||
|
};
|
||||||
|
|
||||||
|
partition@7a00000 {
|
||||||
|
label = "ubi";
|
||||||
|
reg = <0x7a00000 0x8600000>;
|
||||||
|
};
|
||||||
|
};
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
&pciec {
|
||||||
|
status = "okay";
|
||||||
|
|
||||||
|
pcie@1,0 {
|
||||||
|
pinctrl-0 = <&pmx_pcie>;
|
||||||
|
pinctrl-names = "default";
|
||||||
|
status = "okay";
|
||||||
|
reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
|
||||||
|
|
||||||
|
/* -[0000:00]---01.0-[01]----00.0 */
|
||||||
|
/* usbport trigger won't work */
|
||||||
|
bridge@0,1 {
|
||||||
|
compatible = "pci11ab,6710";
|
||||||
|
reg = <0x3800 0 0 0 0>;
|
||||||
|
#address-cells = <3>;
|
||||||
|
#size-cells = <2>;
|
||||||
|
|
||||||
|
usb@1,0 {
|
||||||
|
/* Renesas uPD720202 */
|
||||||
|
compatible = "pci1912,0015";
|
||||||
|
reg = <0x1000 0 0 0 0>;
|
||||||
|
#address-cells = <3>;
|
||||||
|
#size-cells = <2>;
|
||||||
|
|
||||||
|
usb1_port: port@1 {
|
||||||
|
reg = <1>;
|
||||||
|
#trigger-source-cells = <1>;
|
||||||
|
};
|
||||||
|
|
||||||
|
usb2_port: port@2 {
|
||||||
|
reg = <2>;
|
||||||
|
#trigger-source-cells = <1>;
|
||||||
|
};
|
||||||
|
};
|
||||||
|
};
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
&pinctrl {
|
||||||
|
pmx_poweroff: pmx-poweroff {
|
||||||
|
marvell,pins = "mpp7";
|
||||||
|
marvell,function = "gpo";
|
||||||
|
};
|
||||||
|
|
||||||
|
pmx_power_cpu: pmx-power-cpu {
|
||||||
|
marvell,pins = "mpp4";
|
||||||
|
marvell,function = "vdd";
|
||||||
|
};
|
||||||
|
|
||||||
|
pmx_buttons: pmx-buttons {
|
||||||
|
marvell,pins = "mpp6", "mpp10", "mpp14", "mpp32";
|
||||||
|
marvell,function = "gpio";
|
||||||
|
};
|
||||||
|
|
||||||
|
pmx_leds1: pmx-leds1 {
|
||||||
|
marvell,pins = "mpp47";
|
||||||
|
marvell,function = "gpo";
|
||||||
|
};
|
||||||
|
|
||||||
|
pmx_leds2: pmx-leds2 {
|
||||||
|
marvell,pins = "mpp12", "mpp13", "mpp15", "mpp16", "mpp50", "mpp51",
|
||||||
|
"mpp52", "mpp53", "mpp55", "mpp56", "mpp57", "mpp58";
|
||||||
|
marvell,function = "gpio";
|
||||||
|
};
|
||||||
|
|
||||||
|
pmx_pcie: pmx-pcie {
|
||||||
|
marvell,pins = "mpp59";
|
||||||
|
marvell,function = "gpio";
|
||||||
|
};
|
||||||
|
|
||||||
|
/* this gpio is connected to the pin of buzzer
|
||||||
|
* leave it as is due lack of proper driver
|
||||||
|
*/
|
||||||
|
pmx_buzzer: pmx-buzzer {
|
||||||
|
marvell,pins = "mpp63";
|
||||||
|
marvell,function = "gpio";
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
&pmsu {
|
||||||
|
pinctrl-0 = <&pmx_power_cpu>;
|
||||||
|
pinctrl-names = "default";
|
||||||
|
};
|
||||||
|
|
||||||
|
&rtc {
|
||||||
|
status = "disabled";
|
||||||
|
};
|
||||||
|
|
||||||
|
&sata {
|
||||||
|
nr-ports = <2>;
|
||||||
|
status = "okay";
|
||||||
|
#address-cells = <1>;
|
||||||
|
#size-cells = <0>;
|
||||||
|
|
||||||
|
hdd0_temp: sata-port@0 {
|
||||||
|
reg = <0>;
|
||||||
|
#thermal-sensor-cells = <0>;
|
||||||
|
};
|
||||||
|
|
||||||
|
hdd1_temp: sata-port@1 {
|
||||||
|
reg = <1>;
|
||||||
|
#thermal-sensor-cells = <0>;
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
&uart0 {
|
||||||
|
status = "okay";
|
||||||
|
};
|
|
@ -51,6 +51,63 @@ define Build/buffalo-kernel-jffs2
|
||||||
rm -rf $(KDIR)/kernel_jffs2 $@.fakerd
|
rm -rf $(KDIR)/kernel_jffs2 $@.fakerd
|
||||||
endef
|
endef
|
||||||
|
|
||||||
|
# Some info about Ctera firmware:
|
||||||
|
# 1. It's simple tar file (GNU standard), but it must have ".firm" suffix.
|
||||||
|
# 2. It contains two images: kernel and romdisk. Both are required.
|
||||||
|
# 3. Every image has header and trailer file.
|
||||||
|
# 4. The struct of tar firmware is: header kernel trailer header romdisk trailer
|
||||||
|
# 5. In header file are some strings used to describe image. It was decoded from
|
||||||
|
# factory image.
|
||||||
|
# 6. Version format in header file is restricted by Original FW.
|
||||||
|
# 7. Trailer file contains MD5 sum string of header and image file.
|
||||||
|
# 8. Firmware file must have <=24MB size.
|
||||||
|
|
||||||
|
define Build/ctera-firmware
|
||||||
|
mkdir -p $@.tmp
|
||||||
|
|
||||||
|
# Prepare header and trailer file for kernel
|
||||||
|
echo "# CTera firmware information file" > $@.tmp/header
|
||||||
|
echo "image_type=kernel" >> $@.tmp/header
|
||||||
|
echo "arch=ARM" >> $@.tmp/header
|
||||||
|
echo "board=2Drive_A" >> $@.tmp/header
|
||||||
|
echo "version=5.5.165.61499" >> $@.tmp/header
|
||||||
|
echo "kernel_cmd=console=ttyS0,115200 earlycon" >> $@.tmp/header
|
||||||
|
echo "date=$$(date $(if $(SOURCE_DATE_EPOCH),-d@$(SOURCE_DATE_EPOCH)))" \
|
||||||
|
>> $@.tmp/header
|
||||||
|
|
||||||
|
cp $@ $@.tmp/kernel
|
||||||
|
|
||||||
|
echo "MD5=$$(cat $@.tmp/header $@.tmp/kernel | $(MKHASH) md5)" \
|
||||||
|
> $@.tmp/trailer
|
||||||
|
|
||||||
|
tar $(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \
|
||||||
|
-H gnu -C $@.tmp -cf $@.tar header kernel trailer
|
||||||
|
|
||||||
|
# Prepare header and trailer file for fake romdisk
|
||||||
|
echo "# CTera firmware information file" > $@.tmp/header
|
||||||
|
echo "image_type=romdisk" >> $@.tmp/header
|
||||||
|
echo "initrd=yes" >> $@.tmp/header
|
||||||
|
echo "arch=ARM" >> $@.tmp/header
|
||||||
|
echo "board=2Drive_A" >> $@.tmp/header
|
||||||
|
echo "version=5.5.165.61499" >> $@.tmp/header
|
||||||
|
echo "date=$$(date $(if $(SOURCE_DATE_EPOCH),-d@$(SOURCE_DATE_EPOCH)))" \
|
||||||
|
>> $@.tmp/header
|
||||||
|
|
||||||
|
rm -f $@
|
||||||
|
touch $@
|
||||||
|
$(call Build/append-uImage-fakehdr, ramdisk)
|
||||||
|
cp $@ $@.tmp/romdisk
|
||||||
|
|
||||||
|
echo "MD5=$$(cat $@.tmp/header $@.tmp/romdisk | $(MKHASH) md5)" \
|
||||||
|
> $@.tmp/trailer
|
||||||
|
|
||||||
|
tar $(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \
|
||||||
|
-H gnu -C $@.tmp -rf $@.tar header romdisk trailer
|
||||||
|
|
||||||
|
mv $@.tar $@
|
||||||
|
rm -rf $@.tmp
|
||||||
|
endef
|
||||||
|
|
||||||
define Build/sdcard-img
|
define Build/sdcard-img
|
||||||
SIGNATURE="$(IMG_PART_SIGNATURE)" \
|
SIGNATURE="$(IMG_PART_SIGNATURE)" \
|
||||||
./gen_mvebu_sdcard_img.sh $@ \
|
./gen_mvebu_sdcard_img.sh $@ \
|
||||||
|
|
|
@ -31,6 +31,24 @@ define Device/buffalo_ls421de
|
||||||
endef
|
endef
|
||||||
TARGET_DEVICES += buffalo_ls421de
|
TARGET_DEVICES += buffalo_ls421de
|
||||||
|
|
||||||
|
define Device/ctera_c200-v2
|
||||||
|
PAGESIZE := 2048
|
||||||
|
SUBPAGESIZE := 512
|
||||||
|
BLOCKSIZE := 128k
|
||||||
|
DEVICE_VENDOR := Ctera
|
||||||
|
DEVICE_MODEL := C200
|
||||||
|
DEVICE_VARIANT := V2
|
||||||
|
SOC := armada-370
|
||||||
|
KERNEL := kernel-bin | append-dtb | uImage none | ctera-firmware
|
||||||
|
KERNEL_IN_UBI :=
|
||||||
|
KERNEL_SUFFIX := -factory.firm
|
||||||
|
DEVICE_PACKAGES := \
|
||||||
|
kmod-gpio-button-hotplug kmod-hwmon-drivetemp kmod-hwmon-nct7802 \
|
||||||
|
kmod-rtc-s35390a kmod-usb3 kmod-usb-ledtrig-usbport
|
||||||
|
IMAGES := sysupgrade.bin
|
||||||
|
endef
|
||||||
|
TARGET_DEVICES += ctera_c200-v2
|
||||||
|
|
||||||
define Device/cznic_turris-omnia
|
define Device/cznic_turris-omnia
|
||||||
DEVICE_VENDOR := CZ.NIC
|
DEVICE_VENDOR := CZ.NIC
|
||||||
DEVICE_MODEL := Turris Omnia
|
DEVICE_MODEL := Turris Omnia
|
||||||
|
|
Loading…
Reference in New Issue
Block a user