* support latest kernels (4.4 - 5.11)
* coding style cleanups and refactoring
* drop support for sysfs+debugfs
* allow to select routing algorithm during creation of interface
* bugs squashed:
- allocate enough reserved room on fragments for lower devices
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The lowest kernel version supported by OpenWrt at the moment is Linux 5.4.
It is therefore not required to have these dead code sections anymore.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
* support latest kernels (4.4 - 5.9)
* coding style cleanups and refactoring
* introduce a configurable per interface hop penalty
* bugs squashed:
- avoid uninitialized chaddr when handling DHCP
- fix own OGMv2 check in aggregation receive handling
- fix "NOHZ: local_softirq_pending 08" warnings caused by BLA
Signed-off-by: Sven Eckelmann <sven@narfation.org>
* support latest kernels (4.4 - 5.8)
* coding style cleanups and refactoring
* dropped support for kernels < 4.4
* re-enabled link speed detection for interfaces without auto negotiation
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The mac80211 headers might depend on the actual configuration of mac80211
to generate an ABI compatible structure definition. batman-adv must
therefore include the header with these config definitions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
It is easier to use the global define than to manually keep track of the
changes in the various kernel module makefiles in the main OpenWrt
repository and feeds.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The compat-sources are no longer needed for kernels >= 4.4. Older kernel
versions are not used since a while in OpenWrt.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The OpenWrt routing feed was tried to be merged together with the OpenWrt
package feed. But they ended up being rejected due to formalities like the
slightly different package template. Just moving to the OpenWrt package
based one should simplify similar approaches in the future.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
* support latest kernels (3.16 - 5.6)
* coding style cleanups and refactoring
* use wifi tx rates as fallback for the B.A.T.M.A.N. V throughput estimation
* disable deprecated sysfs support by default
* bugs squashed:
- fix crash during the scheduling of OGMs for removed interfaces
Signed-off-by: Sven Eckelmann <sven@narfation.org>
* support latest kernels (3.16 - 5.5)
* coding style cleanups and refactoring
* bugs squashed:
- fix DAT candidate selection on little endian systems
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This changes the package version string so it does not start
with "openwrt", but with the base version we are modifying:
So far: openwrt-2019.4-1
Now: 2019.4-openwrt-1
Since it's us modifying version 2019.4 (in this case), this order
is more convenient (and also closer to what the kernel version
string does).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The '-m' option to select the mesh interface or vlan interfaces was
replaced with device type specific subcommand prefixes:
* meshif <netdev>
* vlan <vdev>
* meshif <netdev> vid <vid>
* hardif <netdev>
This change should also be made in the proto script to allow batctl to drop
the support of '-m' completely in the future.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The mac80211 package version was updated to a 5.2 based one in commit
0b2c42ced21a ("mac80211: Update to version 5.2-rc7"). The batman-adv module
must therefore no longer the pre-5.2 API.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The ap_isolation setting only supports boolean values. So setting an empty
string as ap_isolation is not supported by batctl.
Fixes: f5205d7d24 ("batman-adv: upgrade package to latest release 2014.2.0")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
B.A.T.M.A.N. V support additional settings which are hardif specific. The
batadv_hardif proto has to expose them to allow automatic configuration.
The default configuration would be:
config interface 'bat0_hardif_eth0'
option proto 'batadv_hardif'
option master 'bat0'
option ifname 'eth0'
option mtu '1536'
option 'elp_interval' 500
# string like '1mbit' is accepted instead of kbit for override
option 'throughput_override' '0'
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The state of slave interfaces are handled differently depending on whether
the interface is up or not. All active interfaces (IFF_UP) will transmit
OGMs. But for B.A.T.M.A.N. IV, also non-active interfaces are scheduling
(low TTL) OGMs on active interfaces. The code which setups and schedules
the OGMs must therefore already be called when the interfaces gets added as
slave interface and the transmit function must then check whether it has to
send out the OGM or not on the specific slave interface.
But v2016.3 moved the setup code from the enable function to the activate
function. The latter is called either when the added slave was already up
when batadv_hardif_enable_interface processed the new interface or when a
NETDEV_UP event was received for this slave interfac. As result, each
NETDEV_UP would schedule a new OGM worker for the interface and thus OGMs
would be send a lot more than expected.
Fixes: 549909f89d ("batman-adv: upgrade package to latest release 2016.3")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
* support latest kernels (3.16 - 5.2)
* coding style cleanups and refactoring
* implement multicast-to-unicast support for multiple targets
* deprecate sysfs support and make it optional
* refresh DAT entry timeouts on incoming ARP Replies
* bugs squashed:
- fix multicast tt/tvlv worker locking
- drop roam tvlv handler when unregistering mesh interface
Signed-off-by: Sven Eckelmann <sven@narfation.org>
* support latest kernels (3.16 - 5.1)
* coding style cleanups and refactoring
* implement meshif, hardif and vlan config interface via netlink
* snoop DHCP ACKs to improve DAT cache efficiency
* bugs squashed:
- avoid potential reference counter underflows and use-after free errors for
several objects
- fix GCC warning when B.A.T.M.A.N. V is build in but cfg80211 is not
available
- reject too small VLAN packets before they are processed further
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Although batman-adv config is cycled in config_foreach, changes
are made in the network config. Thus, this one has to be committed.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
batman-adv allows to configure three different objects:
* batadv hardif
- network interface used by batadv meshif to transport the batman-adv
packets
- its master interface is set to the batadv meshif
* batadv (meshif/softif)
- virtual interface that emulates a normal 802.3 interface on top
- encapsulates traffic and forwards it via the batadv hardifs
* batadv vlan
- potential VLAN ID on top of batadv meshif
- allows filtering of traffic from specific VIDs
While batadv vlan objects were already represented as an own proto
"batadv_vlan", the batadv meshif could never be fully configured using
/etc/config/network. Instead, parts of its configuration were stored in
/etc/config/batman_adv and some in the interfaces with the "batadv" proto.
To increase the confusion, the "batadv" proto wasn't used to define the
batadv meshif but to identify batadv (slave) hardifs. The batman-adv
meshifs were also never created directly but only when a hardif was
configured. The actual modification of the configuration settings was then
applied using a hotplug script hack. The batadv meshif network interface
could therefore only be created when an hardif was available and not
manipulated with ifup/ifdown. Also `/etc/init.d/network reload` didn't
modify the batadv meshif interface configuration correctly.
The "batadv" is now renamed to "batadv_hardif" and a new "batadv" proto is
used to configure the main (meshif) network interface with all its
configuration.
A simple network configuration with WiFi & ethernet interfaces and static
IP on top of bat0 would look like:
# batadv meshif bat0
config interface 'bat0'
option proto 'batadv'
option routing_algo 'BATMAN_IV'
option aggregated_ogms 1
option ap_isolation 0
option bonding 0
option fragmentation 1
#option gw_bandwidth '10000/2000'
option gw_mode 'off'
#option gw_sel_class 20
option log_level 0
option orig_interval 1000
option bridge_loop_avoidance 1
option distributed_arp_table 1
option multicast_mode 1
option network_coding 0
option hop_penalty 30
option isolation_mark '0x00000000/0x00000000'
# add *single* wifi-iface with network bat0_hardif_wlan as hardif to bat0
config interface 'bat0_hardif_wlan'
option mtu '1536'
option proto 'batadv_hardif'
option master 'bat0'
# option ifname is filled out by the wifi-iface
# add eth0 as hardif to bat0
config interface 'bat0_hardif_eth0'
option proto 'batadv_hardif'
option master 'bat0'
option ifname 'eth0'
option mtu '1536'
# configure IP on bat0
config interface 'bat0_lan'
option ifname 'bat0'
option proto 'static'
option ipaddr '192.168.1.1'
option netmask '255.255.255.0'
option ip6assign '60'
Signed-off-by: Sven Eckelmann <sven@narfation.org>
hop_penalty is the last remaining setting which is directly writing to
sysfs instead of using a implementation (sysfs vs. netlink) abstraction
layer. batctl now provides a wrapper function that allows the script to
directly use it to take care of communicating with the driver.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The batctl tool should be used for modifying settings in the batman-adv
driver to keep the scripts consistent and allow to use the correct way of
communicating with the kernel (sysfs vs. netlink).
The gw_mode, gw_bandwidth and gw_sel_class options are all handled by
the same gw_mode command in batctl and thus have to be combined depending
on the "gw_mode" value.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
* support latest kernels (3.16 - 5.0)
* coding style cleanups and refactoring
* allow to enable debug tracing without full batman-adv debugfs support
* enable inconsistency reporting for most netlink dump commands
* bugs squashed:
- avoid unnecessary kernel warning (panic) during detection of interface loops
- work around incorrect ethernet header offset in transmit code path
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The batctl binary is currently optional for batman-adv installations. But
new configuration settings will only be exposed via generic netlink. The
batctl tool will therefore be required to modify them.
batctl must therefore no longer depend on batman-adv but batman-adv must
depend on batctl. Some already implemented settings are already moved to
batctl.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
* support latest kernels (3.16 - 4.20)
* coding style cleanups and refactoring
* improve tx performance by avoiding unnecessary locking
* add help messages regarding deprecation of debugfs files
* support for debug message tracepoints
* explicit ELP padding to allow TVLVs in the future
* bugs squashed:
- fix skb_over_panic for merged fragments with small tailroom
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The OpenWrt dependency builder cannot extract the crc16 dependency from
the KMOD_BATMAN_ADV_BLA dependencies. They have to be specified directly in
the OpenWrt Makefile's DEPENDS line to avoid error when BLA is enabled:
Package kmod-batman-adv is missing dependencies for the following libraries:
crc16.ko
Reported-by: Lech Perczak <lech.perczak@gmail.com>
Fixes: 0db66160aa ("batman-adv: Sync config options with kernel Kconfig")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The translation table code from batman-adv is only using the function
crc32c which is part of kmod-lib-crc32c. The kmod-crypto-crc32c is then
only used by kmod-lib-crc32c but not batman-adv.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Kernel modules like ath9k and ath10k are using the same Kconfig option
symbols as used in the kernel. This makes it easier to share them between
these two projects. A similar approach should be used for the batman-adv
module.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The kernel already provides all available kernel options for batman-adv and
even includes more verbose descriptions of each option. Importing this
Kconfig (with minor adjustments) file as Config.in allows to share most
information between kernel and OpenWrt.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
OpenWrt is using a modified version of the software and these modifications
may introduce extra bugs (or behavior changes). It is also patched for
stable releases instead of switching to new releases. The revision should
therefore be added to the version number to make it easier understandable
which modified version the user may have installed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The Module.symvers with the exported symbols of all other kernel modules in
OpenWrt is usually placed in the main source directory of the package. But
the actual sources for batman-adv are found in net/batman-adv. OpenWrt must
therefore be informed to move it to this subdirectory or otherwise modpost
will fail to find the symbols
WARNING: "cfg80211_get_station" [.../batman-adv-2018.3/net/batman-adv/batman-adv.ko] undefined!
The dependency will then be missing in the .modinfo depends= option and
thus it the kernel module loader will not correctly load the cfg80211.ko
during bootup.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
* support latest kernels (3.16 - 4.19)
* coding style cleanups and refactoring
* enable the DAT by default for the in-tree Linux module
* bugs squashed:
- fix segfault when writing to sysfs files under batman_adv/ with
CONFIG_BATMAN_ADV_DEBUG enabled
- avoid information leakage in probe ELP packets
- adjust reference counters when queue_work fails
- prevent duplicated entries in various lists
Signed-off-by: Sven Eckelmann <sven@narfation.org>
* support latest kernels (3.16 - 4.18)
* dropped support for kernels < 3.16 (note the removed build directory)
* coding style cleanups and refactoring
* avoid old nodes disabling multicast optimizations completely
* disable ethtool based B.A.T.M.A.N. V speed detection for virtual interfaces
* enable B.A.T.M.A.N. V compilation by default
* disable debugfs support by default
* bugs squashed:
- fix TT sync flags for intermediate TT responses
- avoid race in TT TVLV allocator helper
- prevent TT request storms by not sending inconsistent TT TVLVs
- fix best gw refcnt after netlink dump
- adjust debugfs paths for interfaces after a namechange
- fix single entry TT non-sync flag storage
- fix multicast TT issues with bogus ROAM flags
- work around insufficient memory initialization in cfg80211's station info
Signed-off-by: Sven Eckelmann <sven@narfation.org>
It is not necessary to install each file manually to the target path. A
simple recursive copy is enough.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The path $(BUILD_DIR)/$(PKG_NAME) is not used anymore. The rule can be
removed and the OpenWrt build system takes care of the removal of the build
directory.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
OpenWrt is able since a while to automatically install all files in ./src/
to the PKG_BUILD_DIR. It is no longer necessary to provide special
Build/Prepare rules to do so.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
cfg80211 is loaded by kmodloader after the modules with a priority
(AutoLoad) are loaded. batman-adv should therefore also be loaded at that
time and must not load cfg80211 itself. The information in the ELF header
are enough for kmodloader to load these two modules in the correct order.
Signed-off-by: Sven Eckelmann <sven@narfation.org>