192 lines
3.2 KiB
Plaintext
192 lines
3.2 KiB
Plaintext
/dts-v1/;
|
|
|
|
#include "ipq8074.dtsi"
|
|
#include "ipq8074-hk-cpu.dtsi"
|
|
#include "ipq8074-ess.dtsi"
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
/ {
|
|
model = "Netgear WAX218";
|
|
compatible = "netgear,wax218", "qcom,ipq8074";
|
|
|
|
aliases {
|
|
serial0 = &blsp1_uart5;
|
|
led-boot = &led_power_amber;
|
|
led-failsafe = &led_power_amber;
|
|
led-running = &led_power_amber;
|
|
led-upgrade = &led_power_amber;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
/*
|
|
* Netgear's U-Boot adds "ubi.mtd=rootfs root=mtd:ubi_rootfs"
|
|
* That fails to create a UBI block device, so add it here.
|
|
*/
|
|
bootargs-append = " ubi.block=0,rootfs root=/dev/ubiblock0_1";
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&tlmm 52 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
|
|
led_spi {
|
|
compatible = "spi-gpio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
sck-gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
|
|
mosi-gpios = <&tlmm 19 GPIO_ACTIVE_HIGH>;
|
|
|
|
led_gpio: led_gpio@0 {
|
|
compatible = "fairchild,74hc595";
|
|
reg = <0>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
registers-number = <1>;
|
|
enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
|
|
spi-max-frequency = <1000000>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_power_amber: led_power {
|
|
label = "amber:power";
|
|
gpios = <&led_gpio 1 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led_lan {
|
|
label = "blue:lan";
|
|
gpios = <&led_gpio 2 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led_wlan_2g {
|
|
label = "blue:wlan2g";
|
|
gpios = <&led_gpio 3 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led_wlan_5g {
|
|
label = "blue:wlan5g";
|
|
gpios = <&led_gpio 4 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&edma {
|
|
status = "okay";
|
|
};
|
|
|
|
&switch {
|
|
status = "okay";
|
|
|
|
switch_cpu_bmp = <0x1>;
|
|
switch_lan_bmp = <0x3e>;
|
|
switch_wan_bmp = <0x40>;
|
|
switch_mac_mode = <0x00>;
|
|
switch_mac_mode1 = <0xff>;
|
|
switch_mac_mode2 = <0x0f>;
|
|
bm_tick_mode = <0>;
|
|
tm_tick_mode = <0>;
|
|
|
|
qcom,port_phyinfo {
|
|
port@5 {
|
|
port_id = <6>;
|
|
phy_address = <28>;
|
|
port_mac_sel = "QGMAC_PORT";
|
|
};
|
|
};
|
|
};
|
|
|
|
&tlmm {
|
|
mdio_pins: mdio-pins {
|
|
mdc {
|
|
pins = "gpio68";
|
|
function = "mdc";
|
|
drive-strength = <8>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
mdio {
|
|
pins = "gpio69";
|
|
function = "mdio";
|
|
drive-strength = <8>;
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
};
|
|
|
|
&mdio {
|
|
status = "okay";
|
|
|
|
pinctrl-0 = <&mdio_pins>;
|
|
pinctrl-names = "default";
|
|
reset-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
|
|
|
|
qca8081_28: ethernet-phy@28 {
|
|
reg = <28>;
|
|
};
|
|
};
|
|
|
|
&dp6_syn {
|
|
status = "okay";
|
|
phy-handle = <&qca8081_28>;
|
|
label = "lan";
|
|
nvmem-cells = <&macaddr_ubootenv_ethaddr>;
|
|
nvmem-cell-names = "mac-address";
|
|
};
|
|
|
|
&qpic_bam {
|
|
status = "okay";
|
|
};
|
|
|
|
&qpic_nand {
|
|
status = "okay";
|
|
|
|
nand@0 {
|
|
reg = <0>;
|
|
nand-ecc-strength = <4>;
|
|
nand-ecc-step-size = <512>;
|
|
nand-bus-width = <8>;
|
|
|
|
partitions {
|
|
compatible = "qcom,smem-part";
|
|
|
|
partition-0-appsblenv {
|
|
compatible = "fixed-partitions";
|
|
label = "0:appsblenv";
|
|
read-only;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
compatible = "u-boot,env";
|
|
label = "env-data";
|
|
reg = <0x0 0x40000>;
|
|
|
|
macaddr_ubootenv_ethaddr: ethaddr {};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&blsp1_uart5 {
|
|
status = "okay";
|
|
};
|
|
|
|
&wifi {
|
|
status = "okay";
|
|
|
|
qcom,ath11k-calibration-variant = "Netgear-WAX218";
|
|
};
|