openwrt/target/linux
Daniel Gimpelevich bc18c2bfe7 ath79: add support for Bluesocket BSAP1880 board
This board was used in dual-band 802.11n enterprise access points, models
BSAP-1800v2 and BSAP-1840, introduced in 2010 by Bluesocket, which was
acquired by Adtran in 2011, who has now EOL'ed them. They differed only in
that the BSAP-1840's antennae were detachable, while the BSAP-1800v2's were
inside the case. They have an external RJ-45 console port, which works with
standard Cisco 72-3383-01 console cables.

Specification:
- System-On-Chip: AR7161
- CPU/Speed: 600 MHz
- Flash-Chip: Macronix MX25L12845E
- Flash size: 16 MiB
- RAM: 64 MiB
- Wireless No1: Lite-On WN2601A card: AR9160/AR9103 2.4GHz 802.11bgn
- Wireless No2: Lite-On WN2502A card: AR9160/AR9106 5GHz 802.11an
- PHY: Vitesse VSC8601, Rev. B

Installation:
1. Connect to the serial console using a terminal that supports YMODEM at
   115200 bps, 8 data bits, no parity, 1 stop bit
2. Interrupt the bootloader using its password, which is: r00t
3. Issue the "fis init" command, confirming if prompted
4. Look at the length of the openwrt-ath79-generic-*-squashfs-kernel.bin
   file, and substitute it below, instead of where I have "LeNgTh"
5. Issue the following command, and upload this file using YMODEM protocol
   load -r -v -b 0x80060000 -m ymodem
6. Issue the following commands, substituting as mentioned above:
   fis create -b 0x80060000 -l LeNgTh vmlinux_2
   load -r -v -b 0x80100000 -m ymodem
7. Using YMODEM, upload openwrt-ath79-generic-*-squashfs-rootfs.bin
8. Issue the "fis free" command, and for the first range in its response,
   use a hexadecimal calculator to subtract the start from the end in order
   to substitute it below, with the leading "0x" to specify it in
   hexadecimal, instead of where I have "LeNgTh"
9. Issue the following commands, substituting as mentioned above:
   fis create -b 0x80100000 -l LeNgTh -e 0 -r 0 rootfs
   reset
10.Wait for the status LED to go solid green

Tested-by: Brian Gonyer <bgonyer@gmail.com>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[fixed obsolete $ARGV in platform_do_upgrade]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-07-17 22:59:29 +02:00
..
apm821xx treewide: sysupgrade: don't use $ARGV in platform_do_upgrade() 2019-07-17 08:05:38 +02:00
ar7 kernel: bump 4.9 to 4.9.153 2019-01-28 18:17:32 +01:00
ar71xx treewide: sysupgrade: don't use $ARGV in platform_do_upgrade() 2019-07-17 08:05:38 +02:00
arc770 treewide: use wpad-basic for not small flash targets 2018-10-16 15:07:41 +01:00
archs38 treewide: use wpad-basic for not small flash targets 2018-10-16 15:07:41 +01:00
armvirt armvirt: fix overlay support by updating to f2fs/ext4 based overlays 2019-06-25 14:12:22 +00:00
at91 at91:renaming subtraget legacy to sam9x 2019-05-30 12:12:57 +02:00
ath25 ath25: split up DEVICE_TITLE 2019-07-10 16:56:16 +02:00
ath79 ath79: add support for Bluesocket BSAP1880 board 2019-07-17 22:59:29 +02:00
bcm53xx bcm53xx: sysupgrade: call nand_do_upgrade() from platform_do_upgrade() 2019-07-08 07:38:12 +02:00
brcm47xx brcm47xx: fix 831-old_gpio_wdt.patch for linux 4.19 2019-07-17 22:59:29 +02:00
brcm63xx brcm63xx: DVA-G3810BN/TL: Fix the WAN ethernet port 2019-06-06 12:05:51 +02:00
brcm2708 brcm2708: Add Raspberry Pi 4 support 2019-07-14 12:44:14 +02:00
cns3xxx treewide: sysupgrade: don't use $ARGV in platform_do_upgrade() 2019-07-17 08:05:38 +02:00
gemini treewide: sysupgrade: don't use $ARGV in platform_do_upgrade() 2019-07-17 08:05:38 +02:00
generic kernel: generic: fix perf build breakage on 4.19 2019-07-17 12:16:29 +02:00
imx6 imx6: apalis: add missing jffs2reset to ramfs during sysupgrade 2019-07-17 12:16:29 +02:00
ipq40xx treewide: sysupgrade: don't use $ARGV in platform_do_upgrade() 2019-07-17 08:05:38 +02:00
ipq806x treewide: sysupgrade: don't use $ARGV in platform_do_upgrade() 2019-07-17 08:05:38 +02:00
ixp4xx treewide: sysupgrade: don't use $ARGV in platform_do_upgrade() 2019-07-17 08:05:38 +02:00
kirkwood treewide: sysupgrade: don't use $ARGV in platform_do_upgrade() 2019-07-17 08:05:38 +02:00
lantiq treewide: sysupgrade: don't use $ARGV in platform_do_upgrade() 2019-07-17 08:05:38 +02:00
layerscape treewide: sysupgrade: don't use $ARGV in platform_do_upgrade() 2019-07-17 08:05:38 +02:00
malta malta: fix overlay support by updating to f2fs/ext4 based overlays 2019-06-25 14:12:22 +00:00
mediatek treewide: sysupgrade: don't use $ARGV in platform_do_upgrade() 2019-07-17 08:05:38 +02:00
mpc85xx treewide: sysupgrade: don't use $ARGV in platform_do_upgrade() 2019-07-17 08:05:38 +02:00
mvebu mvebu: sysupgrade: don't use $ARGV in platform_check_image() 2019-07-17 08:09:41 +02:00
mxs mxs: disable unused serial drivers 2019-03-11 19:35:43 +01:00
octeon treewide: kernel: bump some targets to 4.19 2019-06-18 16:08:55 +02:00
octeontx kernel: Remove CONFIG_COMPAT 2019-05-11 17:15:41 +02:00
omap kernel: Deactivate CONFIG_BINFMT_MISC 2019-05-11 17:15:41 +02:00
orion orion: sysupgrade: change platform_check_image() args validation 2019-07-16 13:58:26 +02:00
oxnas oxnas: convert DEVICE_TITLE to new variables 2019-07-10 16:56:16 +02:00
pistachio kernel: bump 4.14 to 4.14.91 2019-01-07 17:09:06 +01:00
ramips ramips: add MT7615 wireless support for ELECOM WRC-1167GHBK2-S 2019-07-17 14:45:18 +02:00
rb532 rb532: Fix missing DEVICE_TITLE 2019-07-09 20:08:26 +01:00
samsung kernel: Do not set CONFIG_DEVMEM or CONFIG_DEVKMEM 2019-05-11 17:15:41 +02:00
sunxi sunxi: convert to multi-variable device title 2019-07-10 17:01:13 +02:00
tegra tegra: split up DEVICE_TITLE 2019-07-15 19:28:55 +02:00
uml kernel: Deactivate CONFIG_BINFMT_MISC 2019-05-11 17:15:41 +02:00
x86 x86: add modern network modules to Generic target 2019-07-17 12:16:29 +02:00
zynq zynq: convert to multi-variable device title 2019-07-08 16:28:47 +02:00
Makefile