mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2024-06-13 10:49:13 +02:00
a3d8c1295e
The SERCOMM NA502 is a smart home gateway manufactured by SERCOMM and sold under different brands (among others, A1 Telekom Austria SmartHome Gateway). It has multi-protocol radio support in addition to LAN and WiFi. Note: BLE is currently unsupported. Specifications -------------- - MT7621ST 880MHz, Single-Core, Dual-Thread - MT7603EN 2.4GHz WiFi - MT7662EN 5GHz WiFi + BLE - 128MiB NAND - 256MiB DDR3 RAM - SD3503 ZWave Controller - EM357 Zigbee Coordinator MAC address assignment ---------------------- LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the OEM firmware does not enable 5GHz WiFi. Installation ------------ Attach serial console, then boot the initramfs image via TFTP. Once inside OpenWrt, run sysupgrade -n with the sysupgrade file. Attention: The device has a dual-firmware design. We overwrite kernel2, since kernel1 contains an automatic recovery image. If you get NAND ECC errors and are stuck with bad eraseblocks, try to erase the mtd partition first with mtd unlock ubi mtd erase ubi This should only be needed once. Signed-off-by: Andreas Böhler <dev@aboehler.at> [use kiB for IMAGE_SIZE] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
173 lines
4.1 KiB
Plaintext
173 lines
4.1 KiB
Plaintext
|
|
. /lib/functions.sh
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/system.sh
|
|
|
|
ramips_setup_interfaces()
|
|
{
|
|
local board="$1"
|
|
|
|
case $board in
|
|
ampedwireless,ally-00x19k|\
|
|
edimax,re23s|\
|
|
mikrotik,routerboard-m11g|\
|
|
netgear,ex6150|\
|
|
sercomm,na502|\
|
|
thunder,timecloud|\
|
|
tplink,re350-v1|\
|
|
tplink,re500-v1|\
|
|
tplink,re650-v1|\
|
|
ubnt,unifi-6-lite|\
|
|
ubnt,unifi-nanohd)
|
|
ucidef_set_interface_lan "lan"
|
|
;;
|
|
ampedwireless,ally-r1900k|\
|
|
gehua,ghl-r-001|\
|
|
hiwifi,hc5962|\
|
|
xiaomi,mi-router-3-pro|\
|
|
xiaomi,mi-router-ac2100|\
|
|
xiaomi,redmi-router-ac2100)
|
|
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan"
|
|
;;
|
|
asiarf,ap7621-001|\
|
|
winstars,ws-wn583a6)
|
|
ucidef_set_interfaces_lan_wan "lan" "wan"
|
|
;;
|
|
asiarf,ap7621-nv1|\
|
|
glinet,gl-mt1300|\
|
|
jcg,q20|\
|
|
lenovo,newifi-d1|\
|
|
mikrotik,routerboard-m33g|\
|
|
xiaomi,mi-router-3g|\
|
|
xiaomi,mi-router-3g-v2|\
|
|
xiaomi,mi-router-4|\
|
|
xiaomi,mi-router-4a-gigabit)
|
|
ucidef_set_interfaces_lan_wan "lan1 lan2" "wan"
|
|
;;
|
|
gnubee,gb-pc1|\
|
|
gnubee,gb-pc2)
|
|
ucidef_set_interface_lan "lan1 lan2"
|
|
;;
|
|
linksys,re6500|\
|
|
netgear,wac104)
|
|
ucidef_set_interface_lan "lan1 lan2 lan3 lan4"
|
|
;;
|
|
mikrotik,routerboard-750gr3)
|
|
ucidef_set_interfaces_lan_wan "lan2 lan3 lan4 lan5" "wan"
|
|
;;
|
|
mikrotik,routerboard-760igs)
|
|
ucidef_set_interfaces_lan_wan "lan2 lan3 lan4 lan5" "wan sfp"
|
|
;;
|
|
tplink,eap235-wall-v1)
|
|
ucidef_set_interface_lan "lan0 lan1 lan2 lan3"
|
|
;;
|
|
ubnt,edgerouter-x)
|
|
ucidef_set_interfaces_lan_wan "eth1 eth2 eth3 eth4" "eth0"
|
|
;;
|
|
ubnt,edgerouter-x-sfp)
|
|
ucidef_set_interfaces_lan_wan "eth1 eth2 eth3 eth4 eth5" "eth0"
|
|
;;
|
|
zyxel,nr7101)
|
|
ucidef_set_interfaces_lan_wan "lan" "wan"
|
|
;;
|
|
zyxel,wap6805)
|
|
ucidef_set_interface_lan "lan1 lan2 lan3 lan4"
|
|
ucidef_set_interface "qtn" ifname "eth1" protocol "static" ipaddr "1.1.1.1" netmask "255.255.255.0"
|
|
;;
|
|
*)
|
|
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
ramips_setup_macs()
|
|
{
|
|
local board="$1"
|
|
local lan_mac=""
|
|
local wan_mac=""
|
|
local label_mac=""
|
|
|
|
case $board in
|
|
ampedwireless,ally-00x19k)
|
|
lan_mac=$(mtd_get_mac_ascii hwconfig HW.LAN.MAC.Address)
|
|
label_mac=$lan_mac
|
|
;;
|
|
ampedwireless,ally-r1900k)
|
|
lan_mac=$(mtd_get_mac_ascii hwconfig HW.LAN.MAC.Address)
|
|
wan_mac=$(mtd_get_mac_ascii hwconfig HW.WAN.MAC.Address)
|
|
label_mac=$lan_mac
|
|
;;
|
|
asus,rt-ac65p|\
|
|
asus,rt-ac85p)
|
|
wan_mac=$(mtd_get_mac_ascii u-boot-env et1macaddr)
|
|
label_mac=$(mtd_get_mac_binary factory 0x4)
|
|
;;
|
|
buffalo,wsr-1166dhp)
|
|
local index="$(find_mtd_index "board_data")"
|
|
wan_mac="$(grep -m1 mac= "/dev/mtd${index}" | cut -d= -f2)"
|
|
lan_mac=$wan_mac
|
|
;;
|
|
dlink,dir-860l-b1)
|
|
lan_mac=$(mtd_get_mac_ascii factory lanmac)
|
|
wan_mac=$(mtd_get_mac_ascii factory wanmac)
|
|
;;
|
|
edimax,ra21s|\
|
|
edimax,rg21s)
|
|
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
|
|
wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
|
|
;;
|
|
elecom,wrc-2533ghbk-i)
|
|
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
|
|
wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
|
|
label_mac=$wan_mac
|
|
;;
|
|
hiwifi,hc5962)
|
|
lan_mac=$(mtd_get_mac_ascii bdinfo "Vfac_mac ")
|
|
label_mac=$lan_mac
|
|
[ -n "$lan_mac" ] || lan_mac=$(cat /sys/class/net/eth0/address)
|
|
wan_mac=$(macaddr_add "$lan_mac" 1)
|
|
;;
|
|
iodata,wnpr2600g)
|
|
wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
|
|
label_mac=$wan_mac
|
|
;;
|
|
jcg,y2|\
|
|
wavlink,wl-wn531a6|\
|
|
winstars,ws-wn583a6|\
|
|
zbtlink,zbt-we1326|\
|
|
zbtlink,zbt-wg3526-16m|\
|
|
zbtlink,zbt-wg3526-32m)
|
|
label_mac=$(mtd_get_mac_binary factory 0x4)
|
|
;;
|
|
linksys,e5600|\
|
|
linksys,ea7300-v1|\
|
|
linksys,ea7300-v2|\
|
|
linksys,ea7500-v2|\
|
|
linksys,ea8100-v1)
|
|
lan_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
|
wan_mac=$lan_mac
|
|
label_mac=$lan_mac
|
|
;;
|
|
mikrotik,routerboard-750gr3|\
|
|
mikrotik,routerboard-760igs|\
|
|
mikrotik,routerboard-m11g|\
|
|
mikrotik,routerboard-m33g)
|
|
label_mac=$(cat "/sys/firmware/mikrotik/hard_config/mac_base")
|
|
wan_mac=$label_mac
|
|
lan_mac=$(macaddr_add $label_mac 1)
|
|
;;
|
|
esac
|
|
|
|
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
|
|
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
|
|
[ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac
|
|
}
|
|
|
|
board_config_update
|
|
board=$(board_name)
|
|
ramips_setup_interfaces $board
|
|
ramips_setup_macs $board
|
|
board_config_flush
|
|
|
|
exit 0
|