mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2024-06-14 03:03:52 +02:00
c2a7bb520a
Xiaomi Mi Router 4 is the same as Xiaomi Mi Router 3G, except for the RAM (256Mib→128Mib), LEDs and gpio (MiNet button). Specifications: Power: 12 VDC, 1 A Connector type: barrel CPU1: MediaTek MT7621A (880 MHz, 4 cores) FLA1: 128 MiB (ESMT F59L1G81MA) RAM1: 128 MiB (ESMT M15T1G1664A) WI1 chip1: MediaTek MT7603EN WI1 802dot11 protocols: bgn WI1 MIMO config: 2x2:2 WI1 antenna connector: U.FL WI2 chip1: MediaTek MT7612EN WI2 802dot11 protocols: an+ac WI2 MIMO config: 2x2:2 WI2 antenna connector: U.FL ETH chip1: MediaTek MT7621A Switch: MediaTek MT7621A UART Serial [o] TX [o] GND [o] RX [ ] VCC - Do not connect it MAC addresses as verified by OEM firmware: use address source LAN *:c2 factory 0xe000 (label) WAN *:c3 factory 0xe006 2g *:c4 factory 0x0000 5g *:c5 factory 0x8000 Flashing instructions: 1.Create a simple http server (nginx etc) 2.set uart enable To enable writing to the console, you must reset to factory settings Then you see uboot boot, press the keyboard 4 button (enter uboot command line) If it is not successful, repeat the above operation of restoring the factory settings. After entering the uboot command line, type: setenv uart_en 1 saveenv boot 3.use shell in uart cd /tmp wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin kernel1 mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin rootfs0 nvram set flag_try_sys1_failed=1 nvram commit reboot 4.login to the router http://192.168.1.1/ Installation via Software exploit Find the instructions in the https://github.com/acecilia/OpenWRTInvasion Signed-off-by: Dmytro Oz <sequentiality@gmail.com> [commit message facelift, rebase onto shared DTSI/common device definition, bump uboot-envtools] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
147 lines
3.4 KiB
Bash
Executable File
147 lines
3.4 KiB
Bash
Executable File
#!/bin/sh
|
|
|
|
. /lib/functions.sh
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/system.sh
|
|
|
|
ramips_setup_interfaces()
|
|
{
|
|
local board="$1"
|
|
|
|
case $board in
|
|
asiarf,ap7621-001|\
|
|
winstars,ws-wn583a6)
|
|
ucidef_set_interfaces_lan_wan "lan" "wan"
|
|
;;
|
|
asiarf,ap7621-nv1|\
|
|
glinet,gl-mt1300|\
|
|
lenovo,newifi-d1|\
|
|
mikrotik,routerboard-m33g|\
|
|
xiaomi,mi-router-3g|\
|
|
xiaomi,mi-router-3g-v2|\
|
|
xiaomi,mi-router-4|\
|
|
xiaomi,mi-router-4a-gigabit)
|
|
ucidef_set_interfaces_lan_wan "lan1 lan2" "wan"
|
|
;;
|
|
edimax,re23s|\
|
|
mikrotik,routerboard-m11g|\
|
|
netgear,ex6150|\
|
|
thunder,timecloud|\
|
|
tplink,re350-v1|\
|
|
tplink,re500-v1|\
|
|
tplink,re650-v1|\
|
|
ubnt,unifi-6-lite|\
|
|
ubnt,unifi-nanohd)
|
|
ucidef_set_interface_lan "lan"
|
|
;;
|
|
gehua,ghl-r-001|\
|
|
hiwifi,hc5962|\
|
|
xiaomi,mi-router-3-pro|\
|
|
xiaomi,mi-router-ac2100|\
|
|
xiaomi,redmi-router-ac2100)
|
|
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan"
|
|
;;
|
|
gnubee,gb-pc1|\
|
|
gnubee,gb-pc2)
|
|
ucidef_set_interface_lan "lan1 lan2"
|
|
;;
|
|
linksys,re6500|\
|
|
netgear,wac104)
|
|
ucidef_set_interface_lan "lan1 lan2 lan3 lan4"
|
|
;;
|
|
mikrotik,routerboard-750gr3)
|
|
ucidef_set_interfaces_lan_wan "lan2 lan3 lan4 lan5" "wan"
|
|
;;
|
|
mikrotik,routerboard-760igs)
|
|
ucidef_set_interfaces_lan_wan "lan2 lan3 lan4 lan5" "wan sfp"
|
|
;;
|
|
ubnt,edgerouter-x)
|
|
ucidef_set_interfaces_lan_wan "eth1 eth2 eth3 eth4" "eth0"
|
|
;;
|
|
ubnt,edgerouter-x-sfp)
|
|
ucidef_set_interfaces_lan_wan "eth1 eth2 eth3 eth4 eth5" "eth0"
|
|
;;
|
|
zyxel,wap6805)
|
|
ucidef_set_interface_lan "lan1 lan2 lan3 lan4"
|
|
ucidef_set_interface "qtn" ifname "eth1" protocol "static" ipaddr "1.1.1.1" netmask "255.255.255.0"
|
|
;;
|
|
*)
|
|
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
ramips_setup_macs()
|
|
{
|
|
local board="$1"
|
|
local lan_mac=""
|
|
local wan_mac=""
|
|
local label_mac=""
|
|
|
|
case $board in
|
|
asus,rt-ac65p|\
|
|
asus,rt-ac85p)
|
|
wan_mac=$(mtd_get_mac_ascii u-boot-env et1macaddr)
|
|
label_mac=$(mtd_get_mac_binary factory 0x4)
|
|
;;
|
|
buffalo,wsr-1166dhp)
|
|
local index="$(find_mtd_index "board_data")"
|
|
wan_mac="$(grep -m1 mac= "/dev/mtd${index}" | cut -d= -f2)"
|
|
lan_mac=$wan_mac
|
|
;;
|
|
dlink,dir-860l-b1)
|
|
lan_mac=$(mtd_get_mac_ascii factory lanmac)
|
|
wan_mac=$(mtd_get_mac_ascii factory wanmac)
|
|
;;
|
|
edimax,ra21s|\
|
|
edimax,rg21s)
|
|
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
|
|
wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
|
|
;;
|
|
hiwifi,hc5962)
|
|
lan_mac=$(mtd_get_mac_ascii bdinfo "Vfac_mac ")
|
|
label_mac=$lan_mac
|
|
[ -n "$lan_mac" ] || lan_mac=$(cat /sys/class/net/eth0/address)
|
|
wan_mac=$(macaddr_add "$lan_mac" 1)
|
|
;;
|
|
iodata,wnpr2600g)
|
|
wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
|
|
label_mac=$wan_mac
|
|
;;
|
|
linksys,ea7300-v1|\
|
|
linksys,ea7300-v2|\
|
|
linksys,ea7500-v2)
|
|
lan_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
|
wan_mac=$lan_mac
|
|
label_mac=$lan_mac
|
|
;;
|
|
mikrotik,routerboard-750gr3|\
|
|
mikrotik,routerboard-760igs|\
|
|
mikrotik,routerboard-m11g|\
|
|
mikrotik,routerboard-m33g)
|
|
label_mac=$(cat "/sys/firmware/mikrotik/hard_config/mac_base")
|
|
wan_mac=$label_mac
|
|
lan_mac=$(macaddr_add $label_mac 1)
|
|
;;
|
|
wavlink,wl-wn531a6|\
|
|
winstars,ws-wn583a6|\
|
|
zbtlink,zbt-we1326|\
|
|
zbtlink,zbt-wg3526-16m|\
|
|
zbtlink,zbt-wg3526-32m)
|
|
label_mac=$(mtd_get_mac_binary factory 0x4)
|
|
;;
|
|
esac
|
|
|
|
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
|
|
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
|
|
[ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac
|
|
}
|
|
|
|
board_config_update
|
|
board=$(board_name)
|
|
ramips_setup_interfaces $board
|
|
ramips_setup_macs $board
|
|
board_config_flush
|
|
|
|
exit 0
|