openwrt/target/linux/ath25/patches-4.4/108-ar2315_gpio.patch

364 lines
9.8 KiB
Diff

--- a/arch/mips/ath25/Kconfig
+++ b/arch/mips/ath25/Kconfig
@@ -7,6 +7,7 @@ config SOC_AR5312
config SOC_AR2315
bool "Atheros AR2315+ SoC support"
depends on ATH25
+ select GPIO_AR2315
default y
config PCI_AR2315
--- a/arch/mips/ath25/ar2315.c
+++ b/arch/mips/ath25/ar2315.c
@@ -21,6 +21,8 @@
#include <linux/interrupt.h>
#include <linux/platform_device.h>
#include <linux/reboot.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
#include <asm/bootinfo.h>
#include <asm/reboot.h>
#include <asm/time.h>
@@ -167,11 +169,42 @@ void __init ar2315_arch_init_irq(void)
ar2315_misc_irq_domain = domain;
}
+static struct resource ar2315_gpio_res[] = {
+ {
+ .name = "ar2315-gpio",
+ .flags = IORESOURCE_MEM,
+ .start = AR2315_RST_BASE + AR2315_GPIO,
+ .end = AR2315_RST_BASE + AR2315_GPIO + 0x10 - 1,
+ },
+ {
+ .name = "ar2315-gpio",
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .name = "ar2315-gpio-irq-base",
+ .flags = IORESOURCE_IRQ,
+ .start = AR231X_GPIO_IRQ_BASE,
+ .end = AR231X_GPIO_IRQ_BASE,
+ }
+};
+
+static struct platform_device ar2315_gpio = {
+ .id = -1,
+ .name = "ar2315-gpio",
+ .resource = ar2315_gpio_res,
+ .num_resources = ARRAY_SIZE(ar2315_gpio_res)
+};
+
void __init ar2315_init_devices(void)
{
/* Find board configuration */
ath25_find_config(AR2315_SPI_READ_BASE, AR2315_SPI_READ_SIZE);
+ ar2315_gpio_res[1].start = irq_create_mapping(ar2315_misc_irq_domain,
+ AR2315_MISC_IRQ_GPIO);
+ ar2315_gpio_res[1].end = ar2315_gpio_res[1].start;
+ platform_device_register(&ar2315_gpio);
+
ath25_add_wmac(0, AR2315_WLAN0_BASE, AR2315_IRQ_WLAN0);
}
@@ -187,8 +220,8 @@ static void ar2315_restart(char *command
/* Cold reset does not work on the AR2315/6, use the GPIO reset bits
* a workaround. Give it some time to attempt a gpio based hardware
* reset (atheros reference design workaround) */
-
- /* TODO: implement the GPIO reset workaround */
+ gpio_request_one(AR2315_RESET_GPIO, GPIOF_OUT_INIT_LOW, "Reset");
+ mdelay(100);
/* Some boards (e.g. Senao EOC-2610) don't implement the reset logic
* workaround. Attempt to jump to the mips reset location -
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -141,6 +141,13 @@ config GPIO_BRCMSTB
help
Say yes here to enable GPIO support for Broadcom STB (BCM7XXX) SoCs.
+config GPIO_AR2315
+ bool "AR2315 SoC GPIO support"
+ default y if SOC_AR2315
+ depends on SOC_AR2315
+ help
+ Say yes here to enable GPIO support for Atheros AR2315+ SoCs.
+
config GPIO_AR5312
bool "AR5312 SoC GPIO support"
default y if SOC_AR5312
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -21,6 +21,7 @@ obj-$(CONFIG_GPIO_ADP5588) += gpio-adp55
obj-$(CONFIG_GPIO_ALTERA) += gpio-altera.o
obj-$(CONFIG_GPIO_AMD8111) += gpio-amd8111.o
obj-$(CONFIG_GPIO_AMDPT) += gpio-amdpt.o
+obj-$(CONFIG_GPIO_AR2315) += gpio-ar2315.o
obj-$(CONFIG_GPIO_AR5312) += gpio-ar5312.o
obj-$(CONFIG_GPIO_ARIZONA) += gpio-arizona.o
obj-$(CONFIG_ATH79) += gpio-ath79.o
--- /dev/null
+++ b/drivers/gpio/gpio-ar2315.c
@@ -0,0 +1,233 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved.
+ * Copyright (C) 2006 FON Technology, SL.
+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
+ * Copyright (C) 2006 Felix Fietkau <nbd@nbd.name>
+ * Copyright (C) 2012 Alexandros C. Couloumbis <alex@ozo.com>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/irq.h>
+
+#define DRIVER_NAME "ar2315-gpio"
+
+#define AR2315_GPIO_DI 0x0000
+#define AR2315_GPIO_DO 0x0008
+#define AR2315_GPIO_DIR 0x0010
+#define AR2315_GPIO_INT 0x0018
+
+#define AR2315_GPIO_DIR_M(x) (1 << (x)) /* mask for i/o */
+#define AR2315_GPIO_DIR_O(x) (1 << (x)) /* output */
+#define AR2315_GPIO_DIR_I(x) (0) /* input */
+
+#define AR2315_GPIO_INT_NUM_M 0x3F /* mask for GPIO num */
+#define AR2315_GPIO_INT_TRIG(x) ((x) << 6) /* interrupt trigger */
+#define AR2315_GPIO_INT_TRIG_M (0x3 << 6) /* mask for int trig */
+
+#define AR2315_GPIO_INT_TRIG_OFF 0 /* Triggerring off */
+#define AR2315_GPIO_INT_TRIG_LOW 1 /* Low Level Triggered */
+#define AR2315_GPIO_INT_TRIG_HIGH 2 /* High Level Triggered */
+#define AR2315_GPIO_INT_TRIG_EDGE 3 /* Edge Triggered */
+
+#define AR2315_GPIO_NUM 22
+
+static u32 ar2315_gpio_intmask;
+static u32 ar2315_gpio_intval;
+static unsigned ar2315_gpio_irq_base;
+static void __iomem *ar2315_mem;
+
+static inline u32 ar2315_gpio_reg_read(unsigned reg)
+{
+ return __raw_readl(ar2315_mem + reg);
+}
+
+static inline void ar2315_gpio_reg_write(unsigned reg, u32 val)
+{
+ __raw_writel(val, ar2315_mem + reg);
+}
+
+static inline void ar2315_gpio_reg_mask(unsigned reg, u32 mask, u32 val)
+{
+ ar2315_gpio_reg_write(reg, (ar2315_gpio_reg_read(reg) & ~mask) | val);
+}
+
+static void ar2315_gpio_irq_handler(struct irq_desc *desc)
+{
+ u32 pend;
+ int bit = -1;
+
+ /* only do one gpio interrupt at a time */
+ pend = ar2315_gpio_reg_read(AR2315_GPIO_DI);
+ pend ^= ar2315_gpio_intval;
+ pend &= ar2315_gpio_intmask;
+
+ if (pend) {
+ bit = fls(pend) - 1;
+ pend &= ~(1 << bit);
+ ar2315_gpio_intval ^= (1 << bit);
+ }
+
+ /* Enable interrupt with edge detection */
+ if ((ar2315_gpio_reg_read(AR2315_GPIO_DIR) & AR2315_GPIO_DIR_M(bit)) !=
+ AR2315_GPIO_DIR_I(bit))
+ return;
+
+ if (bit >= 0)
+ generic_handle_irq(ar2315_gpio_irq_base + bit);
+}
+
+static void ar2315_gpio_int_setup(unsigned gpio, int trig)
+{
+ u32 reg = ar2315_gpio_reg_read(AR2315_GPIO_INT);
+
+ reg &= ~(AR2315_GPIO_INT_NUM_M | AR2315_GPIO_INT_TRIG_M);
+ reg |= gpio | AR2315_GPIO_INT_TRIG(trig);
+ ar2315_gpio_reg_write(AR2315_GPIO_INT, reg);
+}
+
+static void ar2315_gpio_irq_unmask(struct irq_data *d)
+{
+ unsigned gpio = d->irq - ar2315_gpio_irq_base;
+ u32 dir = ar2315_gpio_reg_read(AR2315_GPIO_DIR);
+
+ /* Enable interrupt with edge detection */
+ if ((dir & AR2315_GPIO_DIR_M(gpio)) != AR2315_GPIO_DIR_I(gpio))
+ return;
+
+ ar2315_gpio_intmask |= (1 << gpio);
+ ar2315_gpio_int_setup(gpio, AR2315_GPIO_INT_TRIG_EDGE);
+}
+
+static void ar2315_gpio_irq_mask(struct irq_data *d)
+{
+ unsigned gpio = d->irq - ar2315_gpio_irq_base;
+
+ /* Disable interrupt */
+ ar2315_gpio_intmask &= ~(1 << gpio);
+ ar2315_gpio_int_setup(gpio, AR2315_GPIO_INT_TRIG_OFF);
+}
+
+static struct irq_chip ar2315_gpio_irq_chip = {
+ .name = DRIVER_NAME,
+ .irq_unmask = ar2315_gpio_irq_unmask,
+ .irq_mask = ar2315_gpio_irq_mask,
+};
+
+static void ar2315_gpio_irq_init(unsigned irq)
+{
+ unsigned i;
+
+ ar2315_gpio_intval = ar2315_gpio_reg_read(AR2315_GPIO_DI);
+ for (i = 0; i < AR2315_GPIO_NUM; i++) {
+ unsigned _irq = ar2315_gpio_irq_base + i;
+
+ irq_set_chip_and_handler(_irq, &ar2315_gpio_irq_chip,
+ handle_level_irq);
+ }
+ irq_set_chained_handler(irq, ar2315_gpio_irq_handler);
+}
+
+static int ar2315_gpio_get_val(struct gpio_chip *chip, unsigned gpio)
+{
+ return (ar2315_gpio_reg_read(AR2315_GPIO_DI) >> gpio) & 1;
+}
+
+static void ar2315_gpio_set_val(struct gpio_chip *chip, unsigned gpio, int val)
+{
+ u32 reg = ar2315_gpio_reg_read(AR2315_GPIO_DO);
+
+ reg = val ? reg | (1 << gpio) : reg & ~(1 << gpio);
+ ar2315_gpio_reg_write(AR2315_GPIO_DO, reg);
+}
+
+static int ar2315_gpio_dir_in(struct gpio_chip *chip, unsigned gpio)
+{
+ ar2315_gpio_reg_mask(AR2315_GPIO_DIR, 1 << gpio, 0);
+ return 0;
+}
+
+static int ar2315_gpio_dir_out(struct gpio_chip *chip, unsigned gpio, int val)
+{
+ ar2315_gpio_reg_mask(AR2315_GPIO_DIR, 0, 1 << gpio);
+ ar2315_gpio_set_val(chip, gpio, val);
+ return 0;
+}
+
+static int ar2315_gpio_to_irq(struct gpio_chip *chip, unsigned gpio)
+{
+ return ar2315_gpio_irq_base + gpio;
+}
+
+static struct gpio_chip ar2315_gpio_chip = {
+ .label = DRIVER_NAME,
+ .direction_input = ar2315_gpio_dir_in,
+ .direction_output = ar2315_gpio_dir_out,
+ .set = ar2315_gpio_set_val,
+ .get = ar2315_gpio_get_val,
+ .to_irq = ar2315_gpio_to_irq,
+ .base = 0,
+ .ngpio = AR2315_GPIO_NUM,
+};
+
+static int ar2315_gpio_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ unsigned irq;
+ int ret;
+
+ if (ar2315_mem)
+ return -EBUSY;
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_IRQ,
+ "ar2315-gpio-irq-base");
+ if (!res) {
+ dev_err(dev, "not found GPIO IRQ base\n");
+ return -ENXIO;
+ }
+ ar2315_gpio_irq_base = res->start;
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_IRQ, DRIVER_NAME);
+ if (!res) {
+ dev_err(dev, "not found IRQ number\n");
+ return -ENXIO;
+ }
+ irq = res->start;
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, DRIVER_NAME);
+ ar2315_mem = devm_ioremap_resource(dev, res);
+ if (IS_ERR(ar2315_mem))
+ return PTR_ERR(ar2315_mem);
+
+ ar2315_gpio_chip.dev = dev;
+ ret = gpiochip_add(&ar2315_gpio_chip);
+ if (ret) {
+ dev_err(dev, "failed to add gpiochip\n");
+ return ret;
+ }
+
+ ar2315_gpio_irq_init(irq);
+
+ return 0;
+}
+
+static struct platform_driver ar2315_gpio_driver = {
+ .probe = ar2315_gpio_probe,
+ .driver = {
+ .name = DRIVER_NAME,
+ .owner = THIS_MODULE,
+ }
+};
+
+static int __init ar2315_gpio_init(void)
+{
+ return platform_driver_register(&ar2315_gpio_driver);
+}
+subsys_initcall(ar2315_gpio_init);
--- a/arch/mips/ath25/devices.h
+++ b/arch/mips/ath25/devices.h
@@ -3,6 +3,11 @@
#include <linux/cpu.h>
+#define AR231X_GPIO_IRQ_BASE 0x30
+
+/* GPIO number for AR2315/16 reset issue workaround */
+#define AR2315_RESET_GPIO 5
+
#define ATH25_REG_MS(_val, _field) (((_val) & _field##_M) >> _field##_S)
#define ATH25_IRQ_CPU_CLOCK (MIPS_CPU_IRQ_BASE + 7) /* C0_CAUSE: 0x8000 */
--- a/arch/mips/ath25/ar2315_regs.h
+++ b/arch/mips/ath25/ar2315_regs.h
@@ -315,6 +315,9 @@
#define AR2315_MEM_CFG_BANKADDR_BITS_M 0x00000018
#define AR2315_MEM_CFG_BANKADDR_BITS_S 3
+/* GPIO MMR base address */
+#define AR2315_GPIO 0x0088
+
/*
* Local Bus Interface Registers
*/