226 lines
3.4 KiB
Plaintext
226 lines
3.4 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
/dts-v1/;
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "mt7981.dtsi"
|
|
|
|
/ {
|
|
model = "JCG Q30 PRO";
|
|
compatible = "jcg,q30-pro", "mediatek,mt7981";
|
|
|
|
aliases {
|
|
serial0 = &uart0;
|
|
label-mac-device = &gmac0;
|
|
led-boot = &led_status_red;
|
|
led-failsafe = &led_status_red;
|
|
led-running = &led_status_blue;
|
|
led-upgrade = &led_status_blue;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
memory {
|
|
reg = <0 0x40000000 0 0x10000000>;
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_status_red: red {
|
|
label = "red:status";
|
|
gpios = <&pio 8 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led_status_blue: blue {
|
|
label = "blue:status";
|
|
gpios = <&pio 13 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
ð {
|
|
status = "okay";
|
|
|
|
gmac0: mac@0 {
|
|
compatible = "mediatek,eth-mac";
|
|
reg = <0>;
|
|
phy-mode = "2500base-x";
|
|
|
|
nvmem-cells = <&macaddr_lan>;
|
|
nvmem-cell-names = "mac-address";
|
|
|
|
fixed-link {
|
|
speed = <2500>;
|
|
full-duplex;
|
|
pause;
|
|
};
|
|
};
|
|
};
|
|
|
|
&mdio_bus {
|
|
switch: switch@0 {
|
|
compatible = "mediatek,mt7531";
|
|
reg = <31>;
|
|
reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <1>;
|
|
interrupt-parent = <&pio>;
|
|
interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
|
|
};
|
|
};
|
|
|
|
&spi0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&spi0_flash_pins>;
|
|
status = "okay";
|
|
|
|
spi_nand@0 {
|
|
compatible = "spi-nand";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
reg = <0>;
|
|
|
|
spi-max-frequency = <52000000>;
|
|
spi-tx-bus-width = <4>;
|
|
spi-rx-bus-width = <4>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "bl2";
|
|
reg = <0x0000000 0x0100000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@100000 {
|
|
label = "u-boot-env";
|
|
reg = <0x0100000 0x0080000>;
|
|
};
|
|
|
|
factory: partition@180000 {
|
|
label = "Factory";
|
|
reg = <0x0180000 0x0200000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@380000 {
|
|
label = "fip";
|
|
reg = <0x0380000 0x0200000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@580000 {
|
|
label = "ubi";
|
|
reg = <0x0580000 0x7000000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&switch {
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
label = "wan";
|
|
nvmem-cells = <&macaddr_wan>;
|
|
nvmem-cell-names = "mac-address";
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
label = "lan1";
|
|
};
|
|
|
|
port@2 {
|
|
reg = <2>;
|
|
label = "lan2";
|
|
};
|
|
|
|
port@3 {
|
|
reg = <3>;
|
|
label = "lan3";
|
|
};
|
|
|
|
port@6 {
|
|
reg = <6>;
|
|
ethernet = <&gmac0>;
|
|
phy-mode = "2500base-x";
|
|
|
|
fixed-link {
|
|
speed = <2500>;
|
|
full-duplex;
|
|
pause;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&pio {
|
|
spi0_flash_pins: spi0-pins {
|
|
mux {
|
|
function = "spi";
|
|
groups = "spi0", "spi0_wp_hold";
|
|
};
|
|
|
|
conf-pu {
|
|
pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
|
|
drive-strength = <8>;
|
|
mediatek,pull-up-adv = <0>; /* bias-disable */
|
|
};
|
|
|
|
conf-pd {
|
|
pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
|
|
drive-strength = <8>;
|
|
mediatek,pull-up-adv = <0>; /* bias-disable */
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&watchdog {
|
|
status = "okay";
|
|
};
|
|
|
|
&wifi {
|
|
status = "okay";
|
|
|
|
mediatek,mtd-eeprom = <&factory 0x0>;
|
|
};
|
|
|
|
&factory {
|
|
compatible = "nvmem-cells";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_wan: macaddr@a0024 {
|
|
reg = <0xa0024 0x6>;
|
|
};
|
|
|
|
macaddr_lan: macaddr@a002a {
|
|
reg = <0xa002a 0x6>;
|
|
};
|
|
};
|