mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2024-06-13 10:49:13 +02:00
59f0a0fd83
This patch adds support for the Edgecore ECW5410 indoor AP. Specification: - SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15 - RAM: 256MB(225 usable) DDR3 - NOR Flash: 16MB SPI NOR - NAND Flash: 128MB S34MS01G2 Parallel NAND - Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0) - USB: 1 x USB 3.0 SuperSpeed - WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn) - CC2540 BLE - UART console on RJ45 next to ethernet ports exposed. Its Cisco pin compatible, 115200 8n1 baud. Installation instructions: Through stock firmware or initramfs. 1.Connect to console 2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe. 3. Transfer factory image 4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path> This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0 Note Initramfs: 1. Connect to console 2. Transfer the image from TFTP server with tftpboot, or by using DHCP advertised image with dhcp command. 3. bootm 4. Run ubiformat /dev/mtd1 You need to interrupt the bootloader after rebooting and run: run altbootcmd This will switch your active rootfs partition to one you wrote to and boot from it. So if rootfs1 is active, then it will change it to rootfs2. This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0 If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those. This will result in wrong ordering and OpenWrt will panic on boot. 5. Transfer sysupgrade image 6. Flash with sysupgrade -n. Note that sysupgrade will write the image to rootfs partition that is not currently in use. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
120 lines
4.1 KiB
Makefile
120 lines
4.1 KiB
Makefile
include $(TOPDIR)/rules.mk
|
|
include $(INCLUDE_DIR)/version.mk
|
|
|
|
PKG_NAME:=ipq-wifi
|
|
PKG_RELEASE:=1
|
|
PKG_FLAGS:=nonshared
|
|
|
|
include $(INCLUDE_DIR)/package.mk
|
|
|
|
define Build/Prepare
|
|
mkdir -p $(PKG_BUILD_DIR)
|
|
endef
|
|
|
|
define Build/Compile
|
|
endef
|
|
|
|
# Use ath10k-bdencoder from https://github.com/qca/qca-swiss-army-knife.git
|
|
# to generate the board-* files here.
|
|
#
|
|
# This is intended to be used on an interim basis until device-specific
|
|
# board data for new devices is available through the upstream compilation
|
|
#
|
|
# Please send a mail with your device-specific board files upstream.
|
|
# You can find instructions and examples on the linux-wireless wiki:
|
|
# <https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles>
|
|
|
|
ALLWIFIBOARDS:= \
|
|
8dev_habanero-dvk \
|
|
aruba_ap-303 \
|
|
avm_fritzrepeater-1200 \
|
|
buffalo_wtr-m2133hp \
|
|
cellc_rtl30vw \
|
|
dlink_dap2610 \
|
|
edgecore_ecw5410 \
|
|
engenius_eap2200 \
|
|
engenius_emd1 \
|
|
engenius_emr3500 \
|
|
ezviz_cs-w3-wd1200g-eup \
|
|
glinet_gl-s1300 \
|
|
linksys_ea8300 \
|
|
mobipromo_cm520-79f \
|
|
qxwlan_e2600ac
|
|
|
|
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
|
|
|
|
define Package/ipq-wifi-default
|
|
SUBMENU:=ath10k Board-Specific Overrides
|
|
SECTION:=firmware
|
|
CATEGORY:=Firmware
|
|
DEPENDS:=@(TARGET_ipq40xx||TARGET_ipq806x)
|
|
TITLE:=Custom Board
|
|
endef
|
|
|
|
define ipq-wifi-install-one-to
|
|
$(INSTALL_DIR) $(2)/lib/firmware/ath10k/$(3)/
|
|
$(INSTALL_DATA) $(1) $(2)/lib/firmware/ath10k/$(3)/board-2.bin
|
|
endef
|
|
|
|
define ipq-wifi-install-one
|
|
$(if $(filter $(suffix $(1)),.QCA4019 .qca4019),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA4019/hw1.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA9888 .qca9888),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9888/hw2.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA9984 .qca9984),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9984/hw1.0),\
|
|
$(error Unrecognized board-file suffix '$(suffix $(1))' for '$(1)')\
|
|
)))
|
|
|
|
endef
|
|
# Blank line required at end of above define due to foreach context
|
|
|
|
define generate-ipq-wifi-package
|
|
define Package/ipq-wifi-$(1)
|
|
$(call Package/ipq-wifi-default)
|
|
TITLE:=board-2.bin Overrides for $(2)
|
|
CONFLICTS:=$(PREV_BOARD)
|
|
endef
|
|
|
|
define Package/ipq-wifi-$(1)/description
|
|
The $(2) requires board-specific, reference ("cal") data
|
|
that is not yet present in the upstream wireless firmware distribution.
|
|
|
|
This package supplies board-2.bin file(s) that, in the interim,
|
|
overwrite those supplied by the ath10k-firmware-* packages.
|
|
|
|
This is package is only necessary for the $(2).
|
|
|
|
Do not install it for any other device!
|
|
endef
|
|
|
|
define Package/ipq-wifi-$(1)/install-overlay
|
|
$$$$(foreach IPQ_WIFI_BOARD_FILE,$$$$(wildcard board-$(1).*),\
|
|
$$$$(call ipq-wifi-install-one,$$$$(IPQ_WIFI_BOARD_FILE),$$(1)))
|
|
endef
|
|
|
|
PREV_BOARD+=ipq-wifi-$(1)
|
|
endef
|
|
|
|
# Add board name to ALLWIFIBOARDS
|
|
# Place files in this directory as board-<devicename>.<qca4019|qca9888|qca9984>
|
|
# Add $(eval $(call generate-ipq-wifi-package,<devicename>,<display name>))
|
|
|
|
$(eval $(call generate-ipq-wifi-package,8dev_habanero-dvk,8devices Habanero DVK))
|
|
$(eval $(call generate-ipq-wifi-package,aruba_ap-303,Aruba AP-303))
|
|
$(eval $(call generate-ipq-wifi-package,avm_fritzrepeater-1200,AVM FRITZRepeater 1200))
|
|
$(eval $(call generate-ipq-wifi-package,buffalo_wtr-m2133hp,Buffalo WTR-M2133HP))
|
|
$(eval $(call generate-ipq-wifi-package,cellc_rtl30vw, Cell C RTL30VW))
|
|
$(eval $(call generate-ipq-wifi-package,dlink_dap2610,D-Link DAP-2610))
|
|
$(eval $(call generate-ipq-wifi-package,edgecore_ecw5410,Edgecore ECW5410))
|
|
$(eval $(call generate-ipq-wifi-package,engenius_eap2200,EnGenius EAP2200))
|
|
$(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1))
|
|
$(eval $(call generate-ipq-wifi-package,engenius_emr3500,EnGenius EMR3500))
|
|
$(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP))
|
|
$(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300))
|
|
$(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
|
|
$(eval $(call generate-ipq-wifi-package,mobipromo_cm520-79f,MobiPromo CM520-79F))
|
|
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC))
|
|
|
|
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))
|