1
0
mirror of https://git.openwrt.org/openwrt/openwrt.git synced 2024-06-16 04:03:56 +02:00
openwrt/target/linux/ramips/dts/mt7621_telco-electronics_x1.dts
Adrian Schmutzler e4ce3109f2 ramips: simplify state_default/pinctrl0 in device DTS files
The node pinctrl0 is already set up in the SOC DTSI files, but
defined again as member of pinctrl in most of the device DTS(I)
files. This patch removes this redundancy for the entire ramips
target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-23 02:24:55 +01:00

165 lines
2.8 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "mt7621.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "telco-electronics,x1", "mediatek,mt7621-soc";
model = "Telco Electronics X1";
aliases {
led-boot = &system_led;
led-failsafe = &system_led;
led-running = &system_led;
led-upgrade = &system_led;
};
chosen {
bootargs = "console=ttyS0,115200";
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
leds {
compatible = "gpio-leds";
system_led: system {
label = "x1:green:system";
gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
};
modem_offline {
label = "x1:red:modem-offline";
gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
};
modem_4g {
label = "x1:blue:modem-4g";
gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
};
modem_3g {
label = "x1:green:modem-3g";
gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
};
modem_rssi_lowest {
label = "x1:green:modem-rssi-lowest";
gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
};
modem_rssi_low {
label = "x1:green:modem-rssi-low";
gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
};
modem_rssi_medium {
label = "x1:green:modem-rssi-medium";
gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
};
modem_rssi_high {
label = "x1:green:modem-rssi-high";
gpios = <&gpio0 30 GPIO_ACTIVE_LOW>;
};
modem_rssi_highest {
label = "x1:green:modem-rssi-highest";
gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
};
};
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <14000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "bootloader";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "config";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x10000>;
read-only;
};
firmware: partition@50000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x50000 0xfb0000>;
};
};
};
};
&gpio0 {
status = "okay";
};
&ethernet {
mtd-mac-address = <&factory 0xe006>;
mediatek,portmap = "llllw";
};
&state_default {
gpio {
ralink,group = "jtag", "uart2", "wdt", "rgmii2";
ralink,function = "gpio";
};
};
&pcie {
status = "okay";
pcie0 {
wifi@0,0 {
compatible = "pci14c3,7603";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x0000>;
ieee80211-freq-limit = <2400000 2500000>;
};
};
pcie1 {
wifi@0,0 {
compatible = "pci14c3,7662";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x8000>;
ieee80211-freq-limit = <5000000 6000000>;
led {
led-sources = <2>;
};
};
};
};