openwrt/target/linux/ath79/dts/ar9344_qihoo_c301.dts

228 lines
3.6 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "ar9344.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
model = "Qihoo 360 C301";
compatible = "qihoo,c301";
aliases {
led-boot = &led_wlan_g;
led-failsafe = &led_wlan_o;
led-upgrade = &led_wlan_o;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&jtag_disable_pins>;
led_wlan_g: wlan_g {
label = "green:wlan";
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
};
led_wlan_o: wlan_o {
label = "orange:wlan";
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy1tpt";
};
};
keys {
compatible = "gpio-keys";
reset {
linux,code = <KEY_RESTART>;
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
reg_eth_led_vbus {
compatible = "regulator-fixed";
regulator-name = "eth_led_vbus";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
gpio = <&gpio 18 GPIO_ACTIVE_LOW>;
};
usb_vbus: reg_usb_vbus {
compatible = "regulator-fixed";
regulator-name = "usb_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
gpio = <&gpio 19 GPIO_ACTIVE_HIGH>;
};
};
&pinmux {
pmx_spi_cs1: pinmux_spi_cs1 {
pinctrl-single,bits = <0xc 0x07 0xff>;
};
pmx_led_switch: pinmux_led_switch {
pinctrl-single,bits = <0x0 0x2b2a2d00 0xffffff00>;
};
};
&ref {
clock-frequency = <40000000>;
};
&gpio {
gpio_ext_lna0 {
gpio-hog;
gpios = <14 0>;
output-high;
line-name = "c301:ext:lna0";
};
gpio_ext_lna1 {
gpio-hog;
gpios = <15 0>;
output-high;
line-name = "c301:ext:lna1";
};
};
&builtin_switch {
pinctrl-names = "default";
pinctrl-0 = <&pmx_led_switch>;
};
&spi {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pmx_spi_cs1>;
flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
uboot: partition@0 {
label = "u-boot";
reg = <0x0 0x40000>;
read-only;
};
partition@40000 {
label = "u-boot-env";
reg = <0x40000 0x10000>;
read-only;
};
partition@50000 {
label = "devdata";
reg = <0x50000 0x10000>;
read-only;
};
partition@60000 {
label = "devconf";
reg = <0x60000 0x10000>;
read-only;
};
partition@70000 {
compatible = "seama";
label = "firmware";
reg = <0x70000 0xf60000>;
};
partition@fd0000 {
label = "warm_start";
reg = <0xfd0000 0x10000>;
read-only;
};
partition@fe0000 {
label = "action_image_config";
reg = <0xfe0000 0x10000>;
};
partition@ff0000 {
label = "radiocfg";
reg = <0xff0000 0x10000>;
read-only;
};
};
};
flash@1 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
reg = <1>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "firmware2";
reg = <0x0 0xf00000>;
};
partition@f00000 {
label = "privatedata";
reg = <0xf00000 0x100000>;
read-only;
};
};
};
};
&usb {
status = "okay";
};
&usb_phy {
status = "okay";
phy-supply = <&usb_vbus>;
};
&pcie {
status = "okay";
wifi@0,0 {
compatible = "qcom,ath10k";
reg = <0 0 0 0 0>;
};
};
&wmac {
status = "okay";
qca,no-eeprom;
};
&eth1 {
status = "okay";
gmac-config {
device = <&gmac>;
switch-phy-swap = <1>;
switch-only-mode = <1>;
};
};
&eth0 {
status = "okay";
phy-handle = <&swphy0>;
};