mirror/openwrt
1
0
Fork 0
mirror of https://git.openwrt.org/openwrt/openwrt.git synced 2024-06-14 03:03:52 +02:00
Code Releases Activity
2449a63208
openwrt/target/linux/ramips/image/mt7621.mk
Bjørn Mork 2449a63208 ramips: mt7621: Add support for ZyXEL NR7101 
The ZyXEL NR7101 is an 802.3at PoE powered 5G outdoor (IP68) CPE
with integrated directional 5G/LTE antennas.

Specifications:

 - SoC: MediaTek MT7621AT
 - RAM: 256 MB
 - Flash: 128 MB MB NAND (MX30LF1G18AC)
 - WiFi: MediaTek MT7603E
 - Switch: 1 LAN port (Gigabiti)
 - 5G/LTE: Quectel RG502Q-EA connected by USB3 to SoC
 - SIM: 2 micro-SIM slots under transparent cover
 - Buttons: Reset, WLAN under same cover
 - LEDs: Multicolour green/red/yellow under same cover (visible)
 - Power: 802.3at PoE via LAN port

The device is built as an outdoor ethernet to 5G/LTE bridge or
router. The Wifi interface is intended for installation and/or
temporary management purposes only.

UART Serial:

57600N1
Located on populated 5 pin header J5:

 [o] GND
 [ ] key - no pin
 [o] RX
 [o] TX
 [o] 3.3V Vcc

Remove the SIM/button/LED cover, the WLAN button and 12 screws
holding the back plate and antenna cover together. The GPS antenna
is fixed to the cover, so be careful with the cable.  Remove 4
screws fixing the antenna board to the main board, again being
careful with the cables.

A bluetooth TTL adapter is recommended for permanent console
access, to keep the router water and dustproof. The 3.3V pin is
able to power such an adapter.

MAC addresses:

OpenWrt OEM   Address          Found as
lan     eth2  08:26:97:*:*:BC  Factory 0xe000 (hex), label
wlan0   ra0   08:26:97:*:*:BD  Factory 0x4 (hex)
wwan0   usb0  random

WARNING!!

ISP managed firmware might at any time update itself to a version
where all known workarounds have been disabled.  Never boot an ISP
managed firmware with a SIM in any of the slots if you intend to use
the router with OpenWrt. The bootloader lock can only be disabled with
root access to running firmware. The flash chip is physically
inaccessible without soldering.

Installation from OEM web GUI:

- Log in as "supervisor" on https://172.17.1.1/
- Upload OpenWrt initramfs-recovery.bin image on the
  Maintenance -> Firmware page
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot

Installation from OEM ssh:

- Log in as "root" on 172.17.1.1 port 22022
- scp OpenWrt initramfs-recovery.bin image to 172.17.1.1:/tmp
- Prepare bootloader config by running:
    nvram setro uboot DebugFlag 0x1
    nvram setro uboot CheckBypass 0
    nvram commit
- Run "mtd_write -w write initramfs-recovery.bin Kernel" and reboot
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot

Copying OpenWrt to the recovery partition:

- Verify that you are running a working OpenWrt recovery image
  from flash
- ssh to root@192.168.1.1 and run:
    fw_setenv CheckBypass 0
    mtd -r erase Kernel2
- Wait while the bootloader mirrors Image1 to Image2

NOTE: This should only be done after successfully booting the OpenWrt
  recovery image from the primary partition during installation.  Do
  not do this after having sysupgraded OpenWrt!  Reinstalling the
  recovery image on normal upgrades is not required or recommended.

Installation from Z-Loader:

- Halt boot by pressing Escape on console
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
  image at 10.10.10.3
- Type "ATNR 1,initramfs-recovery.bin" at the "ZLB>" prompt
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- Sysupgrade to the OpenWrt sysupgrade image

NOTE: ATNR will write the recovery image to both primary and recovery
  partitions in one go.

Booting from RAM:

- Halt boot by pressing Escape on console
- Type "ATGU" at the "ZLB>" prompt to enter the U-Boot menu
- Press "4" to select "4: Entr boot command line interface."
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
  image at 10.10.10.3
- Load it using "tftpboot 0x88000000 initramfs-recovery.bin"
- Boot with "bootm  0x8800017C" to skip the 380 (0x17C) bytes ZyXEL
  header

This method can also be used to RAM boot OEM firmware. The warning
regarding OEM applies!  Never boot an unknown OEM firmware, or any OEM
firmware with a SIM in any slot.

NOTE: U-Boot configuration is incomplete (on some devices?). You may
  have to configure a working mac address before running tftp using
   "setenv eth0addr <mac>"

Unlocking the bootloader:

If you are unebale to halt boot, then the bootloader is locked.

The OEM firmware locks the bootloader on every boot by setting
DebugFlag to 0.  Setting it to 1 is therefore only temporary
when OEM firmware is installed.

- Run "nvram setro uboot DebugFlag 0x1; nvram commit" in OEM firmware
- Run "fw_setenv DebugFlag 0x1" in OpenWrt

  NOTE:
    OpenWrt does this automatically on first boot if necessary

  NOTE2:
    Setting the flag to 0x1 avoids the reset to 0 in known OEM
    versions, but this might change.

  WARNING:
    Writing anything to flash while the bootloader is locked is
    considered extremely risky. Errors might cause a permanent
    brick!

Enabling management access from LAN:

Temporary workaround to allow installing OpenWrt if OEM firmware
has disabled LAN management:

- Connect to console
- Log in as "root"
- Run "iptables -I INPUT -i br0 -j ACCEPT"

Notes on the OEM/bootloader dual partition scheme

The dual partition scheme on this device uses Image2 as a recovery
image only. The device will always boot from Image1, but the
bootloader might copy Image2 to Image1 under specific conditions. This
scheme prevents repurposing of the space occupied by Image2 in any
useful way.

Validation of primary and recovery images is controlled by the
variables CheckBypass, Image1Stable, and Image1Try.

The bootloader sets CheckBypass to 0 and reboots if Image1 fails
validation.

If CheckBypass is 0 and Image1 is invalid then Image2 is copied to
Image1.

If CheckBypass is 0 and Image2 is invalid, then Image1 is copied to
Image2.

If CheckBypass is 1 then all tests are skipped and Image1 is booted
unconditionally.  CheckBypass is set to 1 after each successful
validation of Image1.

Image1Try is incremented if Image1Stable is 0, and Image2 is copied to
Image1 if Image1Try is 3 or larger.  But the bootloader only tests
Image1Try if CheckBypass is 0, which is impossible unless the booted
image sets it to 0 before failing.

The system is therefore not resilient against runtime errors like
failure to mount the rootfs, unless the kernel image sets CheckBypass
to 0 before failing. This is not yet implemented in OpenWrt.

Setting Image1Stable to 1 prevents the bootloader from updating
Image1Try on every boot, saving unnecessary writes to the environment
partition.

Keeping an OpenWrt initramfs recovery as Image2 is recommended
primarily to avoid unwanted OEM firmware boots on failure. Ref the
warning above. It enables console-less recovery in case of some
failures to boot from Image1.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-05-09 09:15:44 +02:00

1543 lines
43 KiB
Makefile
Raw Blame History

#
# MT7621 Profiles
#
include ./common-tp-link.mk
DEFAULT_SOC := mt7621
KERNEL_DTB += -d21
DEVICE_VARS += ELECOM_HWNAME LINKSYS_HWNAME
define Build/elecom-wrc-gs-factory
$(eval product=$(word 1,$(1)))
$(eval version=$(word 2,$(1)))
$(eval hash_opt=$(word 3,$(1)))
$(STAGING_DIR_HOST)/bin/mkhash md5 $(hash_opt) $@ >> $@
( \
echo -n "ELECOM $(product) v$(version)" | \
dd bs=32 count=1 conv=sync; \
dd if=$@; \
) > $@.new
mv $@.new $@
endef
define Build/iodata-factory
$(eval fw_size=$(word 1,$(1)))
$(eval fw_type=$(word 2,$(1)))
$(eval product=$(word 3,$(1)))
$(eval factory_bin=$(word 4,$(1)))
if [ -e $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) -a "$$(stat -c%s $@)" -lt "$(fw_size)" ]; then \
$(CP) $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) $(factory_bin); \
$(STAGING_DIR_HOST)/bin/mksenaofw \
-r 0x30a -p $(product) -t $(fw_type) \
-e $(factory_bin) -o $(factory_bin).new; \
mv $(factory_bin).new $(factory_bin); \
$(CP) $(factory_bin) $(BIN_DIR)/; \
else \
echo "WARNING: initramfs kernel image too big, cannot generate factory image" >&2; \
fi
endef
define Build/iodata-mstc-header
( \
data_size_crc="$$(dd if=$@ ibs=64 skip=1 2>/dev/null | gzip -c | \
tail -c 8 | od -An -tx8 --endian little | tr -d ' \n')"; \
echo -ne "$$(echo $$data_size_crc | sed 's/../\\x&/g')" | \
dd of=$@ bs=8 count=1 seek=7 conv=notrunc 2>/dev/null; \
)
dd if=/dev/zero of=$@ bs=4 count=1 seek=1 conv=notrunc 2>/dev/null
( \
header_crc="$$(dd if=$@ bs=64 count=1 2>/dev/null | gzip -c | \
tail -c 8 | od -An -N4 -tx4 --endian little | tr -d ' \n')"; \
echo -ne "$$(echo $$header_crc | sed 's/../\\x&/g')" | \
dd of=$@ bs=4 count=1 seek=1 conv=notrunc 2>/dev/null; \
)
endef
define Build/ubnt-erx-factory-image
if [ -e $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) -a "$$(stat -c%s $@)" -lt "$(KERNEL_SIZE)" ]; then \
echo '21001:7' > $(1).compat; \
$(TAR) -cf $(1) --transform='s/^.*/compat/' $(1).compat; \
\
$(TAR) -rf $(1) --transform='s/^.*/vmlinux.tmp/' $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE); \
mkhash md5 $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) > $(1).md5; \
$(TAR) -rf $(1) --transform='s/^.*/vmlinux.tmp.md5/' $(1).md5; \
\
echo "dummy" > $(1).rootfs; \
$(TAR) -rf $(1) --transform='s/^.*/squashfs.tmp/' $(1).rootfs; \
\
mkhash md5 $(1).rootfs > $(1).md5; \
$(TAR) -rf $(1) --transform='s/^.*/squashfs.tmp.md5/' $(1).md5; \
\
echo '$(BOARD) $(VERSION_CODE) $(VERSION_NUMBER)' > $(1).version; \
$(TAR) -rf $(1) --transform='s/^.*/version.tmp/' $(1).version; \
\
$(CP) $(1) $(BIN_DIR)/; \
else \
echo "WARNING: initramfs kernel image too big, cannot generate factory image" >&2; \
fi
endef
define Build/zytrx-header
$(eval board=$(word 1,$(1)))
$(eval version=$(word 2,$(1)))
$(STAGING_DIR_HOST)/bin/zytrx -B '$(board)' -v '$(version)' -i $@ -o $@.new
mv $@.new $@
endef
define Device/dsa-migration
DEVICE_COMPAT_VERSION := 1.1
DEVICE_COMPAT_MESSAGE := Config cannot be migrated from swconfig to DSA
endef
define Device/adslr_g7
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := ADSLR
DEVICE_MODEL := G7
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += adslr_g7
define Device/afoundry_ew1200
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := AFOUNDRY
DEVICE_MODEL := EW1200
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt76x2 kmod-mt7603 kmod-usb3 \
kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += ew1200
endef
TARGET_DEVICES += afoundry_ew1200
define Device/alfa-network_quad-e4g
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := Quad-E4G
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 uboot-envtools \
-wpad-basic-wolfssl
endef
TARGET_DEVICES += alfa-network_quad-e4g
define Device/asiarf_ap7621-001
$(Device/dsa-migration)
IMAGE_SIZE := 16000k
DEVICE_VENDOR := AsiaRF
DEVICE_MODEL := AP7621-001
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 -wpad-basic-wolfssl
endef
TARGET_DEVICES += asiarf_ap7621-001
define Device/asiarf_ap7621-nv1
$(Device/dsa-migration)
IMAGE_SIZE := 16000k
DEVICE_VENDOR := AsiaRF
DEVICE_MODEL := AP7621-NV1
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 -wpad-basic-wolfssl
endef
TARGET_DEVICES += asiarf_ap7621-nv1
define Device/asus_rt-ac57u
$(Device/dsa-migration)
DEVICE_VENDOR := ASUS
DEVICE_MODEL := RT-AC57U
IMAGE_SIZE := 16064k
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += asus_rt-ac57u
define Device/asus_rt-ac65p
$(Device/dsa-migration)
DEVICE_VENDOR := ASUS
DEVICE_MODEL := RT-AC65P
IMAGE_SIZE := 51200k
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
IMAGES += factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
check-size
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615e kmod-mt7615-firmware uboot-envtools
endef
TARGET_DEVICES += asus_rt-ac65p
define Device/asus_rt-ac85p
$(Device/dsa-migration)
DEVICE_VENDOR := ASUS
DEVICE_MODEL := RT-AC85P
IMAGE_SIZE := 51200k
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
IMAGES += factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
check-size
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615e kmod-mt7615-firmware uboot-envtools
endef
TARGET_DEVICES += asus_rt-ac85p
define Device/asus_rt-n56u-b1
$(Device/dsa-migration)
DEVICE_VENDOR := ASUS
DEVICE_MODEL := RT-N56U
DEVICE_VARIANT := B1
IMAGE_SIZE := 16064k
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += asus_rt-n56u-b1
define Device/buffalo_wsr-1166dhp
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE/sysupgrade.bin := trx | pad-rootfs | append-metadata
IMAGE_SIZE := 15936k
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := WSR-1166DHP
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
SUPPORTED_DEVICES += wsr-1166
endef
TARGET_DEVICES += buffalo_wsr-1166dhp
define Device/buffalo_wsr-2533dhpl
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 7936k
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := WSR-2533DHPL
DEVICE_ALT0_VENDOR := Buffalo
DEVICE_ALT0_MODEL := WSR-2533DHP
IMAGE/sysupgrade.bin := trx | pad-rootfs | append-metadata
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += buffalo_wsr-2533dhpl
define Device/buffalo_wsr-600dhp
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := WSR-600DHP
DEVICE_PACKAGES := kmod-mt7603 kmod-rt2800-pci
SUPPORTED_DEVICES += wsr-600
endef
TARGET_DEVICES += buffalo_wsr-600dhp
define Device/cudy_wr1300
$(Device/dsa-migration)
IMAGE_SIZE := 15872k
DEVICE_VENDOR := Cudy
DEVICE_MODEL := WR1300
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb2 kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += cudy_wr1300
define Device/dlink_dir-8xx-a1
$(Device/dsa-migration)
IMAGE_SIZE := 16000k
DEVICE_VENDOR := D-Link
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
KERNEL_INITRAMFS := $$(KERNEL) | uimage-padhdr 96
IMAGES += factory.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | uimage-padhdr 96 |\
pad-rootfs | append-metadata | check-size
IMAGE/factory.bin := append-kernel | append-rootfs | uimage-padhdr 96 |\
check-size
endef
define Device/dlink_dir-8xx-r1
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := D-Link
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
KERNEL_INITRAMFS := $$(KERNEL)
IMAGES += factory.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs |\
pad-rootfs | append-metadata | check-size
endef
define Device/dlink_dir-xx60-a1
$(Device/dsa-migration)
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
IMAGE_SIZE := 40960k
UBINIZE_OPTS := -E 5
DEVICE_VENDOR := D-Link
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
kmod-usb-ledtrig-usbport
KERNEL := $$(KERNEL) | uimage-padhdr 96
IMAGES += factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
check-size
endef
define Device/dlink_dir-1960-a1
$(Device/dlink_dir-xx60-a1)
DEVICE_MODEL := DIR-1960
DEVICE_VARIANT := A1
endef
TARGET_DEVICES += dlink_dir-1960-a1
define Device/dlink_dir-2640-a1
$(Device/dlink_dir-xx60-a1)
DEVICE_MODEL := DIR-2640
DEVICE_VARIANT := A1
endef
TARGET_DEVICES += dlink_dir-2640-a1
define Device/dlink_dir-2660-a1
$(Device/dlink_dir-xx60-a1)
DEVICE_MODEL := DIR-2660
DEVICE_VARIANT := A1
endef
TARGET_DEVICES += dlink_dir-2660-a1
define Device/dlink_dir-860l-b1
$(Device/dsa-migration)
$(Device/seama)
BLOCKSIZE := 64k
SEAMA_SIGNATURE := wrgac13_dlink.2013gui_dir860lb
LOADER_TYPE := bin
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | relocate-kernel | \
lzma -a0 | uImage lzma
IMAGE_SIZE := 16064k
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-860L
DEVICE_VARIANT := B1
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += dir-860l-b1
endef
TARGET_DEVICES += dlink_dir-860l-b1
define Device/dlink_dir-867-a1
$(Device/dlink_dir-8xx-a1)
DEVICE_MODEL := DIR-867
DEVICE_VARIANT := A1
endef
TARGET_DEVICES += dlink_dir-867-a1
define Device/dlink_dir-878-a1
$(Device/dlink_dir-8xx-a1)
DEVICE_MODEL := DIR-878
DEVICE_VARIANT := A1
endef
TARGET_DEVICES += dlink_dir-878-a1
define Device/dlink_dir-882-a1
$(Device/dlink_dir-8xx-a1)
DEVICE_MODEL := DIR-882
DEVICE_VARIANT := A1
DEVICE_PACKAGES += kmod-usb3 kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += dlink_dir-882-a1
define Device/dlink_dir-882-r1
$(Device/dlink_dir-8xx-r1)
DEVICE_MODEL := DIR-882
DEVICE_VARIANT := R1
DEVICE_PACKAGES += kmod-usb3 kmod-usb-ledtrig-usbport
IMAGE/factory.bin := append-kernel | append-rootfs | check-size | \
sign-dlink-ru 57c5375741c30ca9ebcb36713db4ba51 \
ab0dff19af8842cdb70a86b4b68d23f7
endef
TARGET_DEVICES += dlink_dir-882-r1
define Device/d-team_newifi-d2
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 32448k
DEVICE_VENDOR := Newifi
DEVICE_MODEL := D2
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += d-team_newifi-d2
define Device/d-team_pbr-m1
$(Device/dsa-migration)
IMAGE_SIZE := 32448k
DEVICE_VENDOR := PandoraBox
DEVICE_MODEL := PBR-M1
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt7603 kmod-mt76x2 kmod-sdhci-mt7620 \
kmod-usb3 kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += pbr-m1
endef
TARGET_DEVICES += d-team_pbr-m1
define Device/edimax_ra21s
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Edimax
DEVICE_MODEL := RA21S
DEVICE_ALT0_VENDOR := Edimax
DEVICE_ALT0_MODEL := Gemini RA21S
IMAGES += factory.bin
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
elx-header 02020040 8844A2D168B45A2D
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += edimax_ra21s
define Device/edimax_re23s
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 15680k
DEVICE_VENDOR := Edimax
DEVICE_MODEL := RE23S
DEVICE_ALT0_VENDOR := Edimax
DEVICE_ALT0_MODEL := Gemini RE23S
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | \
edimax-header -s CSYS -m RN76 -f 0x70000 -S 0x01100000 | pad-rootfs | \
append-metadata | check-size
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | append-rootfs | \
edimax-header -s CSYS -m RN76 -f 0x70000 -S 0x01100000 | pad-rootfs | \
check-size
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += edimax_re23s
define Device/edimax_rg21s
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Edimax
DEVICE_MODEL := Gemini AC2600 RG21S
IMAGES += factory.bin
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
elx-header 02020038 8844A2D168B45A2D
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += edimax_rg21s
define Device/elecom_wrc-1167ghbk2-s
$(Device/dsa-migration)
IMAGE_SIZE := 15488k
DEVICE_VENDOR := ELECOM
DEVICE_MODEL := WRC-1167GHBK2-S
IMAGES += factory.bin
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
elecom-wrc-gs-factory WRC-1167GHBK2-S 0.00
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += elecom_wrc-1167ghbk2-s
define Device/elecom_wrc-gs
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
DEVICE_VENDOR := ELECOM
IMAGES += factory.bin
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
elecom-wrc-gs-factory $$$$(ELECOM_HWNAME) 0.00 -N | \
append-string MT7621_ELECOM_$$$$(ELECOM_HWNAME)
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
define Device/elecom_wrc-1167gs2-b
$(Device/elecom_wrc-gs)
IMAGE_SIZE := 11264k
DEVICE_MODEL := WRC-1167GS2-B
ELECOM_HWNAME := WRC-1167GS2
endef
TARGET_DEVICES += elecom_wrc-1167gs2-b
define Device/elecom_wrc-1167gst2
$(Device/elecom_wrc-gs)
IMAGE_SIZE := 24576k
DEVICE_MODEL := WRC-1167GST2
ELECOM_HWNAME := WRC-1167GST2
endef
TARGET_DEVICES += elecom_wrc-1167gst2
define Device/elecom_wrc-1750gs
$(Device/elecom_wrc-gs)
IMAGE_SIZE := 11264k
DEVICE_MODEL := WRC-1750GS
ELECOM_HWNAME := WRC-1750GS
endef
TARGET_DEVICES += elecom_wrc-1750gs
define Device/elecom_wrc-1750gst2
$(Device/elecom_wrc-gs)
IMAGE_SIZE := 24576k
DEVICE_MODEL := WRC-1750GST2
ELECOM_HWNAME := WRC-1750GST2
endef
TARGET_DEVICES += elecom_wrc-1750gst2
define Device/elecom_wrc-1750gsv
$(Device/elecom_wrc-gs)
IMAGE_SIZE := 11264k
DEVICE_MODEL := WRC-1750GSV
ELECOM_HWNAME := WRC-1750GSV
endef
TARGET_DEVICES += elecom_wrc-1750gsv
define Device/elecom_wrc-1900gst
$(Device/elecom_wrc-gs)
IMAGE_SIZE := 11264k
DEVICE_MODEL := WRC-1900GST
ELECOM_HWNAME := WRC-1900GST
endef
TARGET_DEVICES += elecom_wrc-1900gst
define Device/elecom_wrc-2533ghbk-i
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
DEVICE_VENDOR := ELECOM
DEVICE_MODEL := WRC-2533GHBK-I
IMAGE_SIZE := 9856k
IMAGES += factory.bin
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
elx-header 0107002d 8844A2D168B45A2D | \
elecom-product-header WRC-2533GHBK-I
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += elecom_wrc-2533ghbk-i
define Device/elecom_wrc-2533gst
$(Device/elecom_wrc-gs)
IMAGE_SIZE := 11264k
DEVICE_MODEL := WRC-2533GST
ELECOM_HWNAME := WRC-2533GST
endef
TARGET_DEVICES += elecom_wrc-2533gst
define Device/elecom_wrc-2533gst2
$(Device/elecom_wrc-gs)
IMAGE_SIZE := 24576k
DEVICE_MODEL := WRC-2533GST2
ELECOM_HWNAME := WRC-2533GST2
endef
TARGET_DEVICES += elecom_wrc-2533gst2
define Device/firefly_firewrt
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Firefly
DEVICE_MODEL := FireWRT
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += firewrt
endef
TARGET_DEVICES += firefly_firewrt
define Device/gehua_ghl-r-001
$(Device/dsa-migration)
IMAGE_SIZE := 32448k
DEVICE_VENDOR := GeHua
DEVICE_MODEL := GHL-R-001
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += gehua_ghl-r-001
define Device/glinet_gl-mt1300
$(Device/dsa-migration)
IMAGE_SIZE := 32448k
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-MT1300
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3
endef
TARGET_DEVICES += glinet_gl-mt1300
define Device/gnubee_gb-pc1
$(Device/dsa-migration)
DEVICE_VENDOR := GnuBee
DEVICE_MODEL := Personal Cloud One
DEVICE_PACKAGES := kmod-ata-ahci kmod-usb3 kmod-sdhci-mt7620 -wpad-basic-wolfssl
IMAGE_SIZE := 32448k
endef
TARGET_DEVICES += gnubee_gb-pc1
define Device/gnubee_gb-pc2
$(Device/dsa-migration)
DEVICE_VENDOR := GnuBee
DEVICE_MODEL := Personal Cloud Two
DEVICE_PACKAGES := kmod-ata-ahci kmod-usb3 kmod-sdhci-mt7620 -wpad-basic-wolfssl
IMAGE_SIZE := 32448k
endef
TARGET_DEVICES += gnubee_gb-pc2
define Device/hiwifi_hc5962
$(Device/dsa-migration)
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
UBINIZE_OPTS := -E 5
IMAGE_SIZE := 32768k
IMAGES += factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
check-size
DEVICE_VENDOR := HiWiFi
DEVICE_MODEL := HC5962
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3
endef
TARGET_DEVICES += hiwifi_hc5962
define Device/iodata_wn-ax1167gr
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 15552k
KERNEL_INITRAMFS := $$(KERNEL) | \
iodata-factory 7864320 4 0x1055 $(KDIR)/tmp/$$(KERNEL_INITRAMFS_PREFIX)-factory.bin
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := WN-AX1167GR
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
endef
TARGET_DEVICES += iodata_wn-ax1167gr
define Device/iodata_nand
$(Device/dsa-migration)
DEVICE_VENDOR := I-O DATA
BLOCKSIZE := 128k
PAGESIZE := 2048
UBINIZE_OPTS := -E 5
KERNEL_SIZE := 4096k
IMAGE_SIZE := 51200k
LOADER_TYPE := bin
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | lzma | uImage lzma
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
# The OEM webinterface expects an kernel with initramfs which has the uImage
# header field ih_name.
# We don't want to set the header name field for the kernel include in the
# sysupgrade image as well, as this image shouldn't be accepted by the OEM
# webinterface. It will soft-brick the board.
define Device/iodata_wn-ax1167gr2
$(Device/iodata_nand)
DEVICE_MODEL := WN-AX1167GR2
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
uImage lzma -M 0x434f4d42 -n '3.10(XBC.1)b10' | iodata-mstc-header
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += iodata_wn-ax1167gr2
define Device/iodata_wn-ax2033gr
$(Device/iodata_nand)
DEVICE_MODEL := WN-AX2033GR
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
uImage lzma -M 0x434f4d42 -n '3.10(VST.1)C10' | iodata-mstc-header
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += iodata_wn-ax2033gr
define Device/iodata_wn-dx1167r
$(Device/iodata_nand)
DEVICE_MODEL := WN-DX1167R
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
uImage lzma -M 0x434f4d43 -n '3.10(XIK.1)b10' | iodata-mstc-header
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += iodata_wn-dx1167r
define Device/iodata_wn-dx1200gr
$(Device/iodata_nand)
DEVICE_MODEL := WN-DX1200GR
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
uImage lzma -M 0x434f4d43 -n '3.10(XIQ.0)b20' | iodata-mstc-header
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
endef
TARGET_DEVICES += iodata_wn-dx1200gr
define Device/iodata_wn-gx300gr
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 7616k
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := WN-GX300GR
DEVICE_PACKAGES := kmod-mt7603
endef
TARGET_DEVICES += iodata_wn-gx300gr
define Device/iodata_wnpr2600g
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := WNPR2600G
IMAGE_SIZE := 13952k
IMAGES += factory.bin
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
elx-header 0104003a 8844A2D168B45A2D
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += iodata_wnpr2600g
define Device/iptime_a6ns-m
$(Device/dsa-migration)
IMAGE_SIZE := 16128k
UIMAGE_NAME := a6nm
DEVICE_VENDOR := ipTIME
DEVICE_MODEL := A6ns-M
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += iptime_a6ns-m
define Device/iptime_a8004t
$(Device/dsa-migration)
IMAGE_SIZE := 16128k
UIMAGE_NAME := a8004t
DEVICE_VENDOR := ipTIME
DEVICE_MODEL := A8004T
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3
endef
TARGET_DEVICES += iptime_a8004t
define Device/jcg_jhr-ac876m
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
IMAGES += factory.bin
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | jcg-header 89.1
JCG_MAXSIZE := 16064k
DEVICE_VENDOR := JCG
DEVICE_MODEL := JHR-AC876M
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += jcg_jhr-ac876m
define Device/jcg_y2
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
IMAGES += factory.bin
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | jcg-header 95.1
JCG_MAXSIZE := 16064k
DEVICE_VENDOR := JCG
DEVICE_MODEL := Y2
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3
endef
TARGET_DEVICES += jcg_y2
define Device/lenovo_newifi-d1
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 32448k
DEVICE_VENDOR := Newifi
DEVICE_MODEL := D1
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-sdhci-mt7620 \
kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += newifi-d1
endef
TARGET_DEVICES += lenovo_newifi-d1
define Device/linksys_ea7xxx
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
IMAGE_SIZE := 36864k
DEVICE_VENDOR := Linksys
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615e kmod-mt7615-firmware \
uboot-envtools
UBINIZE_OPTS := -E 5
IMAGES := sysupgrade.bin factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata | check-size
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
append-ubi | check-size | linksys-image type=$$$$(LINKSYS_HWNAME)
endef
define Device/linksys_ea7300-v1
$(Device/linksys_ea7xxx)
DEVICE_MODEL := EA7300
DEVICE_VARIANT := v1
LINKSYS_HWNAME := EA7300
endef
TARGET_DEVICES += linksys_ea7300-v1
define Device/linksys_ea7300-v2
$(Device/linksys_ea7xxx)
DEVICE_MODEL := EA7300
DEVICE_VARIANT := v2
LINKSYS_HWNAME := EA7300v2
DEVICE_PACKAGES += kmod-mt7603
endef
TARGET_DEVICES += linksys_ea7300-v2
define Device/linksys_ea7500-v2
$(Device/linksys_ea7xxx)
DEVICE_MODEL := EA7500
DEVICE_VARIANT := v2
LINKSYS_HWNAME := EA7500v2
endef
TARGET_DEVICES += linksys_ea7500-v2
define Device/linksys_re6500
$(Device/dsa-migration)
IMAGE_SIZE := 7872k
DEVICE_VENDOR := Linksys
DEVICE_MODEL := RE6500
DEVICE_PACKAGES := kmod-mt76x2
SUPPORTED_DEVICES += re6500
endef
TARGET_DEVICES += linksys_re6500
define Device/mediatek_ap-mt7621a-v60
$(Device/dsa-migration)
IMAGE_SIZE := 7872k
DEVICE_VENDOR := Mediatek
DEVICE_MODEL := AP-MT7621A-V60 EVB
DEVICE_PACKAGES := kmod-usb3 kmod-sdhci-mt7620 kmod-sound-mt7620 -wpad-basic-wolfssl
endef
TARGET_DEVICES += mediatek_ap-mt7621a-v60
define Device/mediatek_mt7621-eval-board
$(Device/dsa-migration)
BLOCKSIZE := 64k
IMAGE_SIZE := 15104k
DEVICE_VENDOR := MediaTek
DEVICE_MODEL := MT7621 EVB
DEVICE_PACKAGES := -wpad-basic-wolfssl
SUPPORTED_DEVICES += mt7621
endef
TARGET_DEVICES += mediatek_mt7621-eval-board
define Device/MikroTik
$(Device/dsa-migration)
DEVICE_VENDOR := MikroTik
BLOCKSIZE := 64k
IMAGE_SIZE := 16128k
DEVICE_PACKAGES := kmod-usb3
KERNEL_NAME := vmlinuz
KERNEL := kernel-bin | append-dtb-elf
IMAGE/sysupgrade.bin := append-kernel | kernel2minor -s 1024 | \
pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | append-metadata | \
check-size
endef
define Device/mikrotik_routerboard-750gr3
$(Device/MikroTik)
DEVICE_MODEL := RouterBOARD 750Gr3
DEVICE_PACKAGES += -wpad-basic-wolfssl
SUPPORTED_DEVICES += mikrotik,rb750gr3
endef
TARGET_DEVICES += mikrotik_routerboard-750gr3
define Device/mikrotik_routerboard-760igs
$(Device/MikroTik)
DEVICE_MODEL := RouterBOARD 760iGS
DEVICE_PACKAGES += kmod-sfp -wpad-basic-wolfssl
endef
TARGET_DEVICES += mikrotik_routerboard-760igs
define Device/mikrotik_routerboard-m11g
$(Device/MikroTik)
DEVICE_MODEL := RouterBOARD M11G
DEVICE_PACKAGES := -wpad-basic-wolfssl
SUPPORTED_DEVICES += mikrotik,rbm11g
endef
TARGET_DEVICES += mikrotik_routerboard-m11g
define Device/mikrotik_routerboard-m33g
$(Device/MikroTik)
DEVICE_MODEL := RouterBOARD M33G
DEVICE_PACKAGES := -wpad-basic-wolfssl
SUPPORTED_DEVICES += mikrotik,rbm33g
endef
TARGET_DEVICES += mikrotik_routerboard-m33g
define Device/mqmaker_witi
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := MQmaker
DEVICE_MODEL := WiTi
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt76x2 kmod-sdhci-mt7620 kmod-usb3 \
kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += witi mqmaker,witi-256m mqmaker,witi-512m
endef
TARGET_DEVICES += mqmaker_witi
define Device/mtc_wr1201
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16000k
DEVICE_VENDOR := MTC
DEVICE_MODEL := Wireless Router WR1201
KERNEL_INITRAMFS := $(KERNEL_DTB) | uImage lzma -n 'WR1201_8_128'
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += mtc_wr1201
define Device/netgear_ex6150
$(Device/dsa-migration)
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := EX6150
DEVICE_PACKAGES := kmod-mt76x2
NETGEAR_BOARD_ID := U12H318T00_NETGEAR
IMAGE_SIZE := 14848k
IMAGES += factory.chk
IMAGE/factory.chk := $$(sysupgrade_bin) | check-size | netgear-chk
endef
TARGET_DEVICES += netgear_ex6150
define Device/netgear_sercomm_nand
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
UBINIZE_OPTS := -E 5
IMAGES += factory.img kernel.bin rootfs.bin
IMAGE/factory.img := pad-extra 2048k | append-kernel | pad-to 6144k | \
append-ubi | pad-to $$$$(BLOCKSIZE) | sercom-footer | pad-to 128 | \
zip $$$$(SERCOMM_HWNAME).bin | sercom-seal
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/kernel.bin := append-kernel
IMAGE/rootfs.bin := append-ubi | check-size
DEVICE_VENDOR := NETGEAR
DEVICE_PACKAGES := kmod-mt7603 kmod-usb3 kmod-usb-ledtrig-usbport
endef
define Device/netgear_r6220
$(Device/netgear_sercomm_nand)
DEVICE_MODEL := R6220
SERCOMM_HWNAME := R6220
SERCOMM_HWID := AYA
SERCOMM_HWVER := A001
SERCOMM_SWVER := 0x0086
IMAGE_SIZE := 28672k
DEVICE_PACKAGES += kmod-mt76x2
SUPPORTED_DEVICES += r6220
endef
TARGET_DEVICES += netgear_r6220
define Device/netgear_r6260
$(Device/netgear_sercomm_nand)
DEVICE_MODEL := R6260
SERCOMM_HWNAME := R6260
SERCOMM_HWID := CHJ
SERCOMM_HWVER := A001
SERCOMM_SWVER := 0x0052
IMAGE_SIZE := 40960k
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += netgear_r6260
define Device/netgear_r6350
$(Device/netgear_sercomm_nand)
DEVICE_MODEL := R6350
SERCOMM_HWNAME := R6350
SERCOMM_HWID := CHJ
SERCOMM_HWVER := A001
SERCOMM_SWVER := 0x0052
IMAGE_SIZE := 40960k
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += netgear_r6350
define Device/netgear_r6700-v2
$(Device/netgear_sercomm_nand)
DEVICE_MODEL := R6700
DEVICE_VARIANT := v2
DEVICE_ALT0_VENDOR := NETGEAR
DEVICE_ALT0_MODEL := Nighthawk AC2400
DEVICE_ALT0_VARIANT := v1
DEVICE_ALT1_VENDOR := NETGEAR
DEVICE_ALT1_MODEL := R7200
DEVICE_ALT1_VARIANT := v1
SERCOMM_HWNAME := R6950
SERCOMM_HWID := BZV
SERCOMM_HWVER := A001
SERCOMM_SWVER := 0x1032
IMAGE_SIZE := 40960k
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += netgear_r6700-v2
define Device/netgear_r6800
$(Device/netgear_sercomm_nand)
DEVICE_MODEL := R6800
SERCOMM_HWNAME := R6950
SERCOMM_HWID := BZV
SERCOMM_HWVER := A001
SERCOMM_SWVER := 0x0062
IMAGE_SIZE := 40960k
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += netgear_r6800
define Device/netgear_r6850
$(Device/netgear_sercomm_nand)
DEVICE_MODEL := R6850
SERCOMM_HWNAME := R6850
SERCOMM_HWID := CHJ
SERCOMM_HWVER := A001
SERCOMM_SWVER := 0x0052
IMAGE_SIZE := 40960k
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += netgear_r6850
define Device/netgear_wac104
$(Device/netgear_sercomm_nand)
DEVICE_MODEL := WAC104
SERCOMM_HWNAME := WAC104
SERCOMM_HWID := CAY
SERCOMM_HWVER := A001
SERCOMM_SWVER := 0x0006
IMAGE_SIZE := 28672k
DEVICE_PACKAGES += kmod-mt76x2
endef
TARGET_DEVICES += netgear_wac104
define Device/netgear_wac124
$(Device/netgear_sercomm_nand)
DEVICE_MODEL := WAC124
SERCOMM_HWNAME := WAC124
SERCOMM_HWID := CTL
SERCOMM_HWVER := A003
SERCOMM_SWVER := 0x0402
IMAGE_SIZE := 40960k
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += netgear_wac124
define Device/netgear_wndr3700-v5
$(Device/dsa-migration)
$(Device/netgear_sercomm_nor)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 15232k
DEVICE_MODEL := WNDR3700
DEVICE_VARIANT := v5
SERCOMM_HWNAME := WNDR3700v5
SERCOMM_HWID := AYB
SERCOMM_HWVER := A001
SERCOMM_SWVER := 0x1054
SERCOMM_PAD := 320k
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += wndr3700v5
endef
TARGET_DEVICES += netgear_wndr3700-v5
define Device/netis_wf2881
$(Device/dsa-migration)
BLOCKSIZE := 128k
PAGESIZE := 2048
FILESYSTEMS := squashfs
KERNEL_SIZE := 4096k
IMAGE_SIZE := 129280k
UBINIZE_OPTS := -E 5
UIMAGE_NAME := WF2881_0.0.00
KERNEL_INITRAMFS := $(KERNEL_DTB) | netis-tail WF2881 | uImage lzma
IMAGES += factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
check-size
DEVICE_VENDOR := NETIS
DEVICE_MODEL := WF2881
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += netis_wf2881
define Device/phicomm_k2p
$(Device/dsa-migration)
IMAGE_SIZE := 15744k
DEVICE_VENDOR := Phicomm
DEVICE_MODEL := K2P
DEVICE_ALT0_VENDOR := Phicomm
DEVICE_ALT0_MODEL := KE 2P
SUPPORTED_DEVICES += k2p
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += phicomm_k2p
define Device/planex_vr500
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 65216k
DEVICE_VENDOR := Planex
DEVICE_MODEL := VR500
DEVICE_PACKAGES := kmod-usb3 -wpad-basic-wolfssl
SUPPORTED_DEVICES += vr500
endef
TARGET_DEVICES += planex_vr500
define Device/samknows_whitebox-v8
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := SamKnows
DEVICE_MODEL := Whitebox 8
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport uboot-envtools
SUPPORTED_DEVICES += sk-wb8
endef
TARGET_DEVICES += samknows_whitebox-v8
define Device/storylink_sap-g3200u3
$(Device/dsa-migration)
IMAGE_SIZE := 7872k
DEVICE_VENDOR := STORYLiNK
DEVICE_MODEL := SAP-G3200U3
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += sap-g3200u3
endef
TARGET_DEVICES += storylink_sap-g3200u3
define Device/telco-electronics_x1
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Telco Electronics
DEVICE_MODEL := X1
DEVICE_PACKAGES := kmod-usb3 kmod-mt76
endef
TARGET_DEVICES += telco-electronics_x1
define Device/thunder_timecloud
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Thunder
DEVICE_MODEL := Timecloud
DEVICE_PACKAGES := kmod-usb3 -wpad-basic-wolfssl
SUPPORTED_DEVICES += timecloud
endef
TARGET_DEVICES += thunder_timecloud
define Device/totolink_a7000r
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
UIMAGE_NAME := C8340R1C-9999
DEVICE_VENDOR := TOTOLINK
DEVICE_MODEL := A7000R
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += totolink_a7000r
define Device/totolink_x5000r
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
UIMAGE_NAME := C8343R-9999
DEVICE_VENDOR := TOTOLINK
DEVICE_MODEL := X5000R
DEVICE_PACKAGES := kmod-mt7915e
endef
TARGET_DEVICES += totolink_x5000r
define Device/tplink_eap235-wall-v1
$(Device/dsa-migration)
$(Device/tplink-safeloader)
DEVICE_MODEL := EAP235-Wall
DEVICE_VARIANT := v1
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
TPLINK_BOARD_ID := EAP235-WALL-V1
IMAGE_SIZE := 13440k
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory | \
pad-extra 128
endef
TARGET_DEVICES += tplink_eap235-wall-v1
define Device/tplink_re350-v1
$(Device/dsa-migration)
$(Device/tplink-safeloader)
DEVICE_MODEL := RE350
DEVICE_VARIANT := v1
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
TPLINK_BOARD_ID := RE350-V1
IMAGE_SIZE := 6016k
SUPPORTED_DEVICES += re350-v1
endef
TARGET_DEVICES += tplink_re350-v1
define Device/tplink_re500-v1
$(Device/dsa-migration)
$(Device/tplink-safeloader)
DEVICE_MODEL := RE500
DEVICE_VARIANT := v1
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
TPLINK_BOARD_ID := RE500-V1
IMAGE_SIZE := 14208k
endef
TARGET_DEVICES += tplink_re500-v1
define Device/tplink_re650-v1
$(Device/dsa-migration)
$(Device/tplink-safeloader)
DEVICE_MODEL := RE650
DEVICE_VARIANT := v1
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
TPLINK_BOARD_ID := RE650-V1
IMAGE_SIZE := 14208k
endef
TARGET_DEVICES += tplink_re650-v1
define Device/ubnt_edgerouter_common
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
DEVICE_VENDOR := Ubiquiti
IMAGE_SIZE := 256768k
FILESYSTEMS := squashfs
KERNEL_SIZE := 3145728
KERNEL_INITRAMFS := $$(KERNEL) | \
ubnt-erx-factory-image $(KDIR)/tmp/$$(KERNEL_INITRAMFS_PREFIX)-factory.tar
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
DEVICE_PACKAGES += -wpad-basic-wolfssl
endef
define Device/ubnt_edgerouter-x
$(Device/ubnt_edgerouter_common)
DEVICE_MODEL := EdgeRouter X
SUPPORTED_DEVICES += ubnt-erx ubiquiti,edgerouterx
endef
TARGET_DEVICES += ubnt_edgerouter-x
define Device/ubnt_edgerouter-x-sfp
$(Device/ubnt_edgerouter_common)
DEVICE_MODEL := EdgeRouter X SFP
DEVICE_PACKAGES += kmod-i2c-algo-pca kmod-gpio-pca953x kmod-sfp
SUPPORTED_DEVICES += ubnt-erx-sfp ubiquiti,edgerouterx-sfp
endef
TARGET_DEVICES += ubnt_edgerouter-x-sfp
define Device/ubnt_unifi-6-lite
$(Device/dsa-migration)
DEVICE_VENDOR := Ubiquiti
DEVICE_MODEL := UniFi 6 Lite
DEVICE_DTS_CONFIG := config@1
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7915e
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
IMAGE_SIZE := 15424k
endef
TARGET_DEVICES += ubnt_unifi-6-lite
define Device/ubnt_unifi-nanohd
$(Device/dsa-migration)
DEVICE_VENDOR := Ubiquiti
DEVICE_MODEL := UniFi nanoHD
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
IMAGE_SIZE := 15552k
endef
TARGET_DEVICES += ubnt_unifi-nanohd
define Device/unielec_u7621-01-16m
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := UniElec
DEVICE_MODEL := U7621-01
DEVICE_VARIANT := 16M
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3
endef
TARGET_DEVICES += unielec_u7621-01-16m
define Device/unielec_u7621-06-16m
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := UniElec
DEVICE_MODEL := U7621-06
DEVICE_VARIANT := 16M
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 -wpad-basic-wolfssl
SUPPORTED_DEVICES += u7621-06-256M-16M unielec,u7621-06-256m-16m
endef
TARGET_DEVICES += unielec_u7621-06-16m
define Device/unielec_u7621-06-64m
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 65216k
DEVICE_VENDOR := UniElec
DEVICE_MODEL := U7621-06
DEVICE_VARIANT := 64M
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 -wpad-basic-wolfssl
SUPPORTED_DEVICES += unielec,u7621-06-512m-64m
endef
TARGET_DEVICES += unielec_u7621-06-64m
define Device/wavlink_wl-wn531a6
$(Device/dsa-migration)
DEVICE_VENDOR := Wavlink
DEVICE_MODEL := WL-WN531A6
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware kmod-usb3
IMAGE_SIZE := 15040k
endef
TARGET_DEVICES += wavlink_wl-wn531a6
define Device/wevo_11acnas
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
UIMAGE_NAME := 11AC-NAS-Router(0.0.0)
DEVICE_VENDOR := WeVO
DEVICE_MODEL := 11AC NAS Router
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += 11acnas
endef
TARGET_DEVICES += wevo_11acnas
define Device/wevo_w2914ns-v2
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
UIMAGE_NAME := W2914NS-V2(0.0.0)
DEVICE_VENDOR := WeVO
DEVICE_MODEL := W2914NS
DEVICE_VARIANT := v2
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += w2914nsv2
endef
TARGET_DEVICES += wevo_w2914ns-v2
define Device/winstars_ws-wn583a6
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 7872k
DEVICE_VENDOR := Winstars
DEVICE_MODEL := WS-WN583A6
DEVICE_ALT0_VENDOR := Gemeita
DEVICE_ALT0_MODEL := AC2100
KERNEL_INITRAMFS_SUFFIX := -WN583A6$$(KERNEL_SUFFIX)
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += winstars_ws-wn583a6
define Device/xiaomi_nand_separate
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
DEVICE_VENDOR := Xiaomi
DEVICE_PACKAGES := uboot-envtools
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
UBINIZE_OPTS := -E 5
IMAGES += kernel1.bin rootfs0.bin
IMAGE/kernel1.bin := append-kernel
IMAGE/rootfs0.bin := append-ubi | check-size
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
define Device/xiaomi_mi-router-3g
$(Device/xiaomi_nand_separate)
DEVICE_MODEL := Mi Router 3G
IMAGE_SIZE := 124416k
DEVICE_PACKAGES += kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += R3G mir3g xiaomi,mir3g
endef
TARGET_DEVICES += xiaomi_mi-router-3g
define Device/xiaomi_mi-router-3g-v2
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 14848k
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Mi Router 3G
DEVICE_VARIANT := v2
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
SUPPORTED_DEVICES += xiaomi,mir3g-v2
endef
TARGET_DEVICES += xiaomi_mi-router-3g-v2
define Device/xiaomi_mi-router-3-pro
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE:= 4096k
UBINIZE_OPTS := -E 5
IMAGE_SIZE := 255488k
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Mi Router 3 Pro
IMAGES += factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
check-size
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
kmod-usb-ledtrig-usbport uboot-envtools
SUPPORTED_DEVICES += xiaomi,mir3p
endef
TARGET_DEVICES += xiaomi_mi-router-3-pro
define Device/xiaomi_mi-router-4
$(Device/xiaomi_nand_separate)
DEVICE_MODEL := Mi Router 4
IMAGE_SIZE := 124416k
DEVICE_PACKAGES += kmod-mt7603 kmod-mt76x2
endef
TARGET_DEVICES += xiaomi_mi-router-4
define Device/xiaomi_mi-router-4a-gigabit
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 14848k
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Mi Router 4A
DEVICE_VARIANT := Gigabit Edition
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
endef
TARGET_DEVICES += xiaomi_mi-router-4a-gigabit
define Device/xiaomi_mi-router-ac2100
$(Device/xiaomi_nand_separate)
DEVICE_MODEL := Mi Router AC2100
IMAGE_SIZE := 120320k
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += xiaomi_mi-router-ac2100
define Device/xiaomi_redmi-router-ac2100
$(Device/xiaomi_nand_separate)
DEVICE_MODEL := Redmi Router AC2100
IMAGE_SIZE := 120320k
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += xiaomi_redmi-router-ac2100
define Device/xiaoyu_xy-c5
$(Device/dsa-migration)
IMAGE_SIZE := 32448k
DEVICE_VENDOR := XiaoYu
DEVICE_MODEL := XY-C5
DEVICE_PACKAGES := kmod-ata-ahci kmod-usb3 -wpad-basic-wolfssl
endef
TARGET_DEVICES += xiaoyu_xy-c5
define Device/xzwifi_creativebox-v1
$(Device/dsa-migration)
IMAGE_SIZE := 32448k
DEVICE_VENDOR := CreativeBox
DEVICE_MODEL := v1
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt7603 kmod-mt76x2 kmod-sdhci-mt7620 \
kmod-usb3 -wpad-basic-wolfssl
endef
TARGET_DEVICES += xzwifi_creativebox-v1
define Device/youhua_wr1200js
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := YouHua
DEVICE_MODEL := WR1200JS
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += youhua_wr1200js
define Device/youku_yk-l2
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Youku
DEVICE_MODEL := YK-L2
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += youku_yk-l2
define Device/zbtlink_zbt-we1326
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Zbtlink
DEVICE_MODEL := ZBT-WE1326
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-sdhci-mt7620
SUPPORTED_DEVICES += zbt-we1326
endef
TARGET_DEVICES += zbtlink_zbt-we1326
define Device/zbtlink_zbt-we3526
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Zbtlink
DEVICE_MODEL := ZBT-WE3526
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += zbtlink_zbt-we3526
define Device/zbtlink_zbt-wg2626
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Zbtlink
DEVICE_MODEL := ZBT-WG2626
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += zbt-wg2626
endef
TARGET_DEVICES += zbtlink_zbt-wg2626
define Device/zbtlink_zbt-wg3526-16m
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Zbtlink
DEVICE_MODEL := ZBT-WG3526
DEVICE_VARIANT := 16M
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 \
kmod-usb3 kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += zbt-wg3526 zbt-wg3526-16M
endef
TARGET_DEVICES += zbtlink_zbt-wg3526-16m
define Device/zbtlink_zbt-wg3526-32m
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 32448k
DEVICE_VENDOR := Zbtlink
DEVICE_MODEL := ZBT-WG3526
DEVICE_VARIANT := 32M
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 \
kmod-usb3 kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += ac1200pro zbt-wg3526-32M
endef
TARGET_DEVICES += zbtlink_zbt-wg3526-32m
define Device/zio_freezio
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := ZIO
DEVICE_MODEL := FREEZIO
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += zio_freezio
define Device/zyxel_nr7101
$(Device/dsa-migration)
BLOCKSIZE := 128k
PAGESIZE := 2048
UBINIZE_OPTS := -E 5
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := NR7101
DEVICE_PACKAGES := kmod-mt7603 kmod-usb3 uboot-envtools kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
KERNEL := $(KERNEL_DTB) | uImage lzma | zytrx-header $$(DEVICE_MODEL) $$(VERSION_DIST)-$$(REVISION)
KERNEL_INITRAMFS := $(KERNEL_DTB) | uImage lzma | zytrx-header $$(DEVICE_MODEL) 9.99(ABUV.9)$$(VERSION_DIST)-recovery
KERNEL_INITRAMFS_SUFFIX := -recovery.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += zyxel_nr7101
define Device/zyxel_wap6805
$(Device/dsa-migration)
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
UBINIZE_OPTS := -E 5
IMAGE_SIZE := 32448k
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := WAP6805
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7621-qtn-rgmii
KERNEL := $(KERNEL_DTB) | uImage lzma | uimage-padhdr 160
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += zyxel_wap6805
View Git Blame Copy Permalink