Go to file
Sven Eckelmann 0b20490207 ipq40xx: add support for OpenMesh A62
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
  - QCA9888 hw2.0 (PCI)
  - requires special BDF in QCA9888/hw2.0/board-2.bin
    bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
  - triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
  - phy@mdio3:
    + Label: Ethernet 1
    + gmac0 (ethaddr) in original firmware
    + 802.3at POE+
  - phy@mdio4:
    + Label: Ethernet 2
    + gmac1 (eth1addr) in original firmware
    + 18-24V passive POE (mode B)
* powered only via POE

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

The initramfs image can be started using

  setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
  tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
  set fdt_high 0x85000000
  bootm 0x84000000

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-04-23 22:07:22 +02:00
.github merge: github: use OpenWrt in issue/pr templates 2018-01-03 20:36:57 +01:00
config config: fix ARM64 dependency check 2018-02-10 20:16:39 +01:00
include build: consolidate fake uImage header build commands 2018-04-20 20:58:52 +02:00
package ipq40xx: add support for OpenMesh A62 2018-04-23 22:07:22 +02:00
scripts ipq40xx: add support for OpenMesh A62 2018-04-23 22:07:22 +02:00
target ipq40xx: add support for OpenMesh A62 2018-04-23 22:07:22 +02:00
toolchain toolchain/glibc: unset LD_LIBRARY_PATH 2018-04-19 14:39:41 +02:00
tools tools: mkimage: provide dtc path during build 2018-04-19 08:34:34 +02:00
.gitattributes add .gitattributes to prevent the git autocrlf option from messing with CRLF/LF in files 2012-05-08 13:30:49 +00:00
.gitignore .gitignore: add .project & .cproject for eclipse users 2018-01-17 11:07:17 +01:00
BSDmakefile add missing copyright header 2007-02-26 01:05:09 +00:00
Config.in merge: base: update base-files and basic config 2017-12-08 19:41:18 +01:00
LICENSE finally move buildroot-ng to trunk 2016-03-20 17:29:15 +01:00
Makefile merge: base: update base-files and basic config 2017-12-08 19:41:18 +01:00
README merge: base: update base-files and basic config 2017-12-08 19:41:18 +01:00
feeds.conf.default feeds: switch git.lede-project.org URLs to git.openwrt.org 2018-01-16 16:59:22 +01:00
rules.mk imagebuilder: reuse rootfs preparation from rootfs.mk 2018-03-07 09:59:08 +01:00

README

This is the buildsystem for the OpenWrt Linux distribution.

Please use "make menuconfig" to choose your preferred
configuration for the toolchain and firmware.

You need to have installed gcc, binutils, bzip2, flex, python, perl, make,
find, grep, diff, unzip, gawk, getopt, subversion, libz-dev and libc headers.

Run "./scripts/feeds update -a" to get all the latest package definitions
defined in feeds.conf / feeds.conf.default respectively
and "./scripts/feeds install -a" to install symlinks of all of them into
package/feeds/.

Use "make menuconfig" to configure your image.

Simply running "make" will build your firmware.
It will download all sources, build the cross-compile toolchain, 
the kernel and all choosen applications.

To build your own firmware you need to have access to a Linux, BSD or MacOSX system
(case-sensitive filesystem required). Cygwin will not be supported because of
the lack of case sensitiveness in the file system.


Sunshine!
	Your OpenWrt Community
	http://www.openwrt.org