From: Landen Chao Date: Fri, 4 Sep 2020 22:21:57 +0800 Subject: [PATCH] net: dsa: mt7530: Extend device data ready for adding a new hardware Add a structure holding required operations for each device such as device initialization, PHY port read or write, a checker whether PHY interface is supported on a certain port, MAC port setup for either bus pad or a specific PHY interface. The patch is done for ready adding a new hardware MT7531, and keep the same setup logic of existing hardware. Signed-off-by: Landen Chao Signed-off-by: Sean Wang --- --- a/drivers/net/dsa/mt7530.c +++ b/drivers/net/dsa/mt7530.c @@ -373,8 +373,9 @@ mt7530_fdb_write(struct mt7530_priv *pri mt7530_write(priv, MT7530_ATA1 + (i * 4), reg[i]); } +/* Setup TX circuit including relevant PAD and driving */ static int -mt7530_pad_clk_setup(struct dsa_switch *ds, int mode) +mt7530_pad_clk_setup(struct dsa_switch *ds, phy_interface_t interface) { struct mt7530_priv *priv = ds->priv; u32 ncpo1, ssc_delta, trgint, i, xtal; @@ -388,7 +389,7 @@ mt7530_pad_clk_setup(struct dsa_switch * return -EINVAL; } - switch (mode) { + switch (interface) { case PHY_INTERFACE_MODE_RGMII: trgint = 0; /* PLL frequency: 125MHz */ @@ -410,7 +411,8 @@ mt7530_pad_clk_setup(struct dsa_switch * } break; default: - dev_err(priv->dev, "xMII mode %d not supported\n", mode); + dev_err(priv->dev, "xMII interface %d not supported\n", + interface); return -EINVAL; } @@ -1335,12 +1337,11 @@ mt7530_setup(struct dsa_switch *ds) return 0; } -static void mt7530_phylink_mac_config(struct dsa_switch *ds, int port, - unsigned int mode, - const struct phylink_link_state *state) +static bool +mt7530_phy_mode_supported(struct dsa_switch *ds, int port, + const struct phylink_link_state *state) { struct mt7530_priv *priv = ds->priv; - u32 mcr_cur, mcr_new; switch (port) { case 0: /* Internal phy */ @@ -1349,33 +1350,114 @@ static void mt7530_phylink_mac_config(st case 3: case 4: if (state->interface != PHY_INTERFACE_MODE_GMII) - return; + goto unsupported; break; case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */ - if (priv->p5_interface == state->interface) - break; if (!phy_interface_mode_is_rgmii(state->interface) && state->interface != PHY_INTERFACE_MODE_MII && state->interface != PHY_INTERFACE_MODE_GMII) - return; + goto unsupported; + break; + case 6: /* 1st cpu port */ + if (state->interface != PHY_INTERFACE_MODE_RGMII && + state->interface != PHY_INTERFACE_MODE_TRGMII) + goto unsupported; + break; + default: + dev_err(priv->dev, "%s: unsupported port: %i\n", __func__, + port); + goto unsupported; + } + + return true; + +unsupported: + return false; +} + +static bool +mt753x_phy_mode_supported(struct dsa_switch *ds, int port, + const struct phylink_link_state *state) +{ + struct mt7530_priv *priv = ds->priv; + + return priv->info->phy_mode_supported(ds, port, state); +} + +static int +mt753x_pad_setup(struct dsa_switch *ds, const struct phylink_link_state *state) +{ + struct mt7530_priv *priv = ds->priv; + + return priv->info->pad_setup(ds, state->interface); +} + +static int +mt7530_mac_config(struct dsa_switch *ds, int port, unsigned int mode, + phy_interface_t interface) +{ + struct mt7530_priv *priv = ds->priv; + + /* Only need to setup port5. */ + if (port != 5) + return 0; + + mt7530_setup_port5(priv->ds, interface); + + return 0; +} + +static int +mt753x_mac_config(struct dsa_switch *ds, int port, unsigned int mode, + const struct phylink_link_state *state) +{ + struct mt7530_priv *priv = ds->priv; + + return priv->info->mac_port_config(ds, port, mode, state->interface); +} + +static void +mt753x_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode, + const struct phylink_link_state *state) +{ + struct mt7530_priv *priv = ds->priv; + u32 mcr_cur, mcr_new; + + if (!mt753x_phy_mode_supported(ds, port, state)) + goto unsupported; + + switch (port) { + case 0: /* Internal phy */ + case 1: + case 2: + case 3: + case 4: + if (state->interface != PHY_INTERFACE_MODE_GMII) + goto unsupported; + break; + case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */ + if (priv->p5_interface == state->interface) + break; + + if (mt753x_mac_config(ds, port, mode, state) < 0) + goto unsupported; - mt7530_setup_port5(ds, state->interface); break; case 6: /* 1st cpu port */ if (priv->p6_interface == state->interface) break; - if (state->interface != PHY_INTERFACE_MODE_RGMII && - state->interface != PHY_INTERFACE_MODE_TRGMII) - return; + mt753x_pad_setup(ds, state); - /* Setup TX circuit incluing relevant PAD and driving */ - mt7530_pad_clk_setup(ds, state->interface); + if (mt753x_mac_config(ds, port, mode, state) < 0) + goto unsupported; priv->p6_interface = state->interface; break; default: - dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port); +unsupported: + dev_err(ds->dev, "%s: unsupported %s port: %i\n", + __func__, phy_modes(state->interface), port); return; } @@ -1443,61 +1525,44 @@ static void mt7530_phylink_mac_link_up(s mt7530_set(priv, MT7530_PMCR_P(port), mcr); } -static void mt7530_phylink_validate(struct dsa_switch *ds, int port, - unsigned long *supported, - struct phylink_link_state *state) +static void +mt7530_mac_port_validate(struct dsa_switch *ds, int port, + unsigned long *supported) { + if (port == 5) + phylink_set(supported, 1000baseX_Full); +} + +static void +mt753x_phylink_validate(struct dsa_switch *ds, int port, + unsigned long *supported, + struct phylink_link_state *state) +{ + struct mt7530_priv *priv = ds->priv; __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, }; - switch (port) { - case 0: /* Internal phy */ - case 1: - case 2: - case 3: - case 4: - if (state->interface != PHY_INTERFACE_MODE_NA && - state->interface != PHY_INTERFACE_MODE_GMII) - goto unsupported; - break; - case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */ - if (state->interface != PHY_INTERFACE_MODE_NA && - !phy_interface_mode_is_rgmii(state->interface) && - state->interface != PHY_INTERFACE_MODE_MII && - state->interface != PHY_INTERFACE_MODE_GMII) - goto unsupported; - break; - case 6: /* 1st cpu port */ - if (state->interface != PHY_INTERFACE_MODE_NA && - state->interface != PHY_INTERFACE_MODE_RGMII && - state->interface != PHY_INTERFACE_MODE_TRGMII) - goto unsupported; - break; - default: - dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port); -unsupported: + if (state->interface != PHY_INTERFACE_MODE_NA && + !mt753x_phy_mode_supported(ds, port, state)) { linkmode_zero(supported); return; } phylink_set_port_modes(mask); - phylink_set(mask, Autoneg); - if (state->interface == PHY_INTERFACE_MODE_TRGMII) { - phylink_set(mask, 1000baseT_Full); - } else { + if (state->interface != PHY_INTERFACE_MODE_TRGMII) { phylink_set(mask, 10baseT_Half); phylink_set(mask, 10baseT_Full); phylink_set(mask, 100baseT_Half); phylink_set(mask, 100baseT_Full); - - if (state->interface != PHY_INTERFACE_MODE_MII) { - /* This switch only supports 1G full-duplex. */ - phylink_set(mask, 1000baseT_Full); - if (port == 5) - phylink_set(mask, 1000baseX_Full); - } + phylink_set(mask, Autoneg); } + /* This switch only supports 1G full-duplex. */ + if (state->interface != PHY_INTERFACE_MODE_MII) + phylink_set(mask, 1000baseT_Full); + + priv->info->mac_port_validate(ds, port, mask); + phylink_set(mask, Pause); phylink_set(mask, Asym_Pause); @@ -1593,12 +1658,45 @@ static int mt7530_set_mac_eee(struct dsa return 0; } +static int +mt753x_phylink_mac_link_state(struct dsa_switch *ds, int port, + struct phylink_link_state *state) +{ + struct mt7530_priv *priv = ds->priv; + + return priv->info->mac_port_get_state(ds, port, state); +} + +static int +mt753x_setup(struct dsa_switch *ds) +{ + struct mt7530_priv *priv = ds->priv; + + return priv->info->sw_setup(ds); +} + +static int +mt753x_phy_read(struct dsa_switch *ds, int port, int regnum) +{ + struct mt7530_priv *priv = ds->priv; + + return priv->info->phy_read(ds, port, regnum); +} + +static int +mt753x_phy_write(struct dsa_switch *ds, int port, int regnum, u16 val) +{ + struct mt7530_priv *priv = ds->priv; + + return priv->info->phy_write(ds, port, regnum, val); +} + static const struct dsa_switch_ops mt7530_switch_ops = { .get_tag_protocol = mtk_get_tag_protocol, - .setup = mt7530_setup, + .setup = mt753x_setup, .get_strings = mt7530_get_strings, - .phy_read = mt7530_phy_read, - .phy_write = mt7530_phy_write, + .phy_read = mt753x_phy_read, + .phy_write = mt753x_phy_write, .get_ethtool_stats = mt7530_get_ethtool_stats, .get_sset_count = mt7530_get_sset_count, .port_enable = mt7530_port_enable, @@ -1615,18 +1713,43 @@ static const struct dsa_switch_ops mt753 .port_vlan_del = mt7530_port_vlan_del, .port_mirror_add = mt7530_port_mirror_add, .port_mirror_del = mt7530_port_mirror_del, - .phylink_validate = mt7530_phylink_validate, - .phylink_mac_link_state = mt7530_phylink_mac_link_state, - .phylink_mac_config = mt7530_phylink_mac_config, + .phylink_validate = mt753x_phylink_validate, + .phylink_mac_link_state = mt753x_phylink_mac_link_state, + .phylink_mac_config = mt753x_phylink_mac_config, .phylink_mac_link_down = mt7530_phylink_mac_link_down, .phylink_mac_link_up = mt7530_phylink_mac_link_up, .get_mac_eee = mt7530_get_mac_eee, .set_mac_eee = mt7530_set_mac_eee, }; +static const struct mt753x_info mt753x_table[] = { + [ID_MT7621] = { + .id = ID_MT7621, + .sw_setup = mt7530_setup, + .phy_read = mt7530_phy_read, + .phy_write = mt7530_phy_write, + .pad_setup = mt7530_pad_clk_setup, + .phy_mode_supported = mt7530_phy_mode_supported, + .mac_port_validate = mt7530_mac_port_validate, + .mac_port_get_state = mt7530_phylink_mac_link_state, + .mac_port_config = mt7530_mac_config, + }, + [ID_MT7530] = { + .id = ID_MT7530, + .sw_setup = mt7530_setup, + .phy_read = mt7530_phy_read, + .phy_write = mt7530_phy_write, + .pad_setup = mt7530_pad_clk_setup, + .phy_mode_supported = mt7530_phy_mode_supported, + .mac_port_validate = mt7530_mac_port_validate, + .mac_port_get_state = mt7530_phylink_mac_link_state, + .mac_port_config = mt7530_mac_config, + }, +}; + static const struct of_device_id mt7530_of_match[] = { - { .compatible = "mediatek,mt7621", .data = (void *)ID_MT7621, }, - { .compatible = "mediatek,mt7530", .data = (void *)ID_MT7530, }, + { .compatible = "mediatek,mt7621", .data = &mt753x_table[ID_MT7621], }, + { .compatible = "mediatek,mt7530", .data = &mt753x_table[ID_MT7530], }, { /* sentinel */ }, }; MODULE_DEVICE_TABLE(of, mt7530_of_match); @@ -1664,8 +1787,21 @@ mt7530_probe(struct mdio_device *mdiodev /* Get the hardware identifier from the devicetree node. * We will need it for some of the clock and regulator setup. */ - priv->id = (unsigned int)(unsigned long) - of_device_get_match_data(&mdiodev->dev); + priv->info = of_device_get_match_data(&mdiodev->dev); + if (!priv->info) + return -EINVAL; + + /* Sanity check if these required device operations are filled + * properly. + */ + if (!priv->info->sw_setup || !priv->info->pad_setup || + !priv->info->phy_read || !priv->info->phy_write || + !priv->info->phy_mode_supported || + !priv->info->mac_port_validate || + !priv->info->mac_port_get_state || !priv->info->mac_port_config) + return -EINVAL; + + priv->id = priv->info->id; if (priv->id == ID_MT7530) { priv->core_pwr = devm_regulator_get(&mdiodev->dev, "core"); --- a/drivers/net/dsa/mt7530.h +++ b/drivers/net/dsa/mt7530.h @@ -11,7 +11,7 @@ #define MT7530_NUM_FDB_RECORDS 2048 #define MT7530_ALL_MEMBERS 0xff -enum { +enum mt753x_id { ID_MT7530 = 0, ID_MT7621 = 1, }; @@ -451,6 +451,40 @@ static const char *p5_intf_modes(unsigne } } +/* struct mt753x_info - This is the main data structure for holding the specific + * part for each supported device + * @sw_setup: Holding the handler to a device initialization + * @phy_read: Holding the way reading PHY port + * @phy_write: Holding the way writing PHY port + * @pad_setup: Holding the way setting up the bus pad for a certain + * MAC port + * @phy_mode_supported: Check if the PHY type is being supported on a certain + * port + * @mac_port_validate: Holding the way to set addition validate type for a + * certan MAC port + * @mac_port_get_state: Holding the way getting the MAC/PCS state for a certain + * MAC port + * @mac_port_config: Holding the way setting up the PHY attribute to a + * certain MAC port + */ +struct mt753x_info { + enum mt753x_id id; + + int (*sw_setup)(struct dsa_switch *ds); + int (*phy_read)(struct dsa_switch *ds, int port, int regnum); + int (*phy_write)(struct dsa_switch *ds, int port, int regnum, u16 val); + int (*pad_setup)(struct dsa_switch *ds, phy_interface_t interface); + bool (*phy_mode_supported)(struct dsa_switch *ds, int port, + const struct phylink_link_state *state); + void (*mac_port_validate)(struct dsa_switch *ds, int port, + unsigned long *supported); + int (*mac_port_get_state)(struct dsa_switch *ds, int port, + struct phylink_link_state *state); + int (*mac_port_config)(struct dsa_switch *ds, int port, + unsigned int mode, + phy_interface_t interface); +}; + /* struct mt7530_priv - This is the main data structure for holding the state * of the driver * @dev: The device pointer @@ -476,6 +510,7 @@ struct mt7530_priv { struct regulator *core_pwr; struct regulator *io_pwr; struct gpio_desc *reset; + const struct mt753x_info *info; unsigned int id; bool mcm; phy_interface_t p6_interface;