Replace my o2.pl email address.
I'm still available at the old address.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Manually rebased patches:
ath79/patches-5.4/910-unaligned_access_hacks.patch
bcm27xx/patches-5.4/950-0135-spi-spi-bcm2835-Disable-forced-software-CS.patch
bcm27xx/patches-5.4/950-0414-SQUASH-Fix-spi-driver-compiler-warnings.patch
ipq806x/patches-5.4/093-4-v5.8-ipq806x-PCI-qcom-Use-bulk-clk-api-and-assert-on-error.patch
Removed since could be reverse-applied by quilt and found to be included upstream:
ipq806x/patches-5.4/096-PCI-qcom-Make-sure-PCIe-is-reset-before-init-for-rev.patch
All modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[refresh altered targets after rebase]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
qca9558_devolo_dvl1xxx.dtsi contains device specific nodes which
are inherited for some DTS files and overwritten for others.
This is considered confusing, so move the relevant nodes/properties
to the devices and only keep the shared stuff in the DTSI.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
[clarify commit title/message, move &gmac_config in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link EAP225 v3 is an AC1350 (802.11ac Wave-2) ceiling mount access
point. Serial port access for debricking requires fine soldering.
Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MINO
* Ethernet (AR8033): 1× 1GbE, 802.3at PoE
Flashing instructions:
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface
Debricking:
* Serial port can be soldered on PCB J3 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R225 (TXD) and R237 (RXD).
Do NOT bridge R230.
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via LuCI web interface
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM boot log:
Using interface ath0 with hwaddr b0:...:3e and ssid "..."
Using interface ath10 with hwaddr b0:...:3f and ssid "..."
Tested by forum user blinkstar88
Signed-off-by: Sander Vanheule <sander@svanheule.net>
TP-Link EAP225-Outdoor v1 is an AC1200 (802.11ac Wave-2) pole or wall
mount access point. Debricking requires access to the serial port, which
is non-trivial.
Device specifications:
* SoC: QCA9563 @ 775MHz
* Memory: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n 2x2
* Wireless 5GHz (QCA9886): a/n/ac 2x2 MU-MIMO
* Ethernet (AR8033): 1× 1GbE, PoE
Flashing instructions:
* ssh into target device with recent (>= v1.6.0) firmware
* run `cliclientd stopcs` on target device
* upload factory image via web interface
Debricking:
To recover the device, you need access to the serial port. This requires
fine soldering to test points, or the use of probe pins.
* Open the case and solder wires to the test points: RXD, TXD and TPGND4
* Use a 3.3V UART, 115200 baud, 8n1
* Interrupt bootloader by holding ctrl+B during boot
* upload initramfs via built-in tftp client and perform sysupgrade
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From stock ifconfig:
ath0 Link encap:Ethernet HWaddr D8:...:2E
ath10 Link encap:Ethernet HWaddr D8:...:2F
br0 Link encap:Ethernet HWaddr D8:...:2E
eth0 Link encap:Ethernet HWaddr D8:...:2E
Tested by forum user PolynomialDivision on firmware v1.7.0.
UART access tested by forum user arinc9.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
TP-Link EAP245 v1 is an AC1750 (802.11ac Wave-1) ceiling mount access point.
Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9880): a/n/ac, 3x3
* Ethernet (AR8033): 1× 1GbE, 802.3at PoE
Flashing instructions:
* Upgrade the device to firmware v1.4.0 if necessary
* Exploit the user management page in the web interface to start telnetd
by changing the username to `;/usr/sbin/telnetd -l/bin/sh&`.
* Immediately change the malformed username back to something valid
(e.g. 'admin') to make ssh work again.
* Use the root shell via telnet to make /tmp world writeable (chmod 777)
* Extract /usr/bin/uclited from the device via ssh and apply the binary
patch listed below. The patch is required to prevent `uclited -u` in
the last step from crashing.
* Copy the patched uclited programme back to the device at /tmp/uclited
(via ssh)
* Upload the factory image to /tmp/upgrade.bin (via ssh)
* Run `chmod +x /tmp/uclited && /tmp/uclited -u` to install OpenWrt.
--- xxd uclited
+++ xxd uclited-patched
@@ -53796,7 +53796,7 @@
000d2240: 8c44 0000 0320 f809 0000 0000 8fbc 0010 .D... ..........
000d2250: 8fa6 0a4c 02c0 2821 8f82 87b8 0000 0000 ...L..(!........
-000d2260: 8c44 0000 0c13 45e0 27a7 0018 8fbc 0010 .D....E.'.......
+000d2260: 8c44 0000 2402 0000 0000 0000 8fbc 0010 .D..$...........
000d2270: 1040 001d 0000 1821 8f99 8374 3c04 0058 .@.....!...t<..X
000d2280: 3c05 0056 2484 a898 24a5 9a30 0320 f809 <..V$...$..0. ..
Debricking:
* Serial port can be soldered on PCB J3 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R225 (TXD) and R237 (RXD).
Do NOT bridge R230.
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via the LuCI web interface
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
Tested on the EAP245 v1 running the latest firmware (v1.4.0). The binary
patch might not apply to uclited from other firmware versions.
EAP245 v1 device support was originally developed and maintained by
Julien Dusser out-of-tree. This patch and "ath79: prepare for 1-port
TP-Link EAP2x5 devices" are based on that work.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
TP-Link has developed a number of access points based on the AP152
reference board. In the EAP-series of 802.11ac access points, this
includes the following devices with one ethernet port:
* EAP225 v1/v2
* EAP225 v3
* EAP225-Outdoor v1
* EAP245 v1
Since the only differences between these devices are the ath10k wireless
radios and LEDs, a common base is provided for the overlapping support
requirements.
Hardware commonalities:
* SoC: QCA9563-AL3A MIPS 74kc v5.0 @ 775MHz, AHB @ 258MHz
* RAM: 128MiB DDR2 @ 650MHz
* Flash: 16MiB SPI NOR
* Wi-Fi 2.4GHz: provided by SoC
* Wi-Fi 5Ghz: ath10k chip on PCIe
* Ethernet: AR8033-AL1A, one 1GbE port (802.3at PoE)
Signed-off-by: Sander Vanheule <sander@svanheule.net>
This commit add a workaround for non working SGMII link observed on some
QCA956x SoCs. The workaround originates part from the U-Boot source code
from QCA, part from the implementation from TP-Link found in the GPL
tarball for the EAP245v1.
Extends commit 0d416a8d3b for QCA956x.
Note that reset is the same on QCA955x and QCA956x, same register offset
and values.
Auto calibration is done on u-boot, but always fall back to default value
0x7. Add a DTS entry serdes-cal in case a device require another value.
Signed-off-by: Julien Dusser <julien.dusser@free.fr>
[Sander Vanheule:
Minor code style fixes,
Remove hunk adding qca956x-serdes-fixup to a missing DTS,
Remove variable err that was only assigned,
Rename function to sgmii_serdes_init,
Lower priority of serdes call message to pr_debug]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Some bootloaders do not set up gmac0 properly, leaving it disconnected
from the sgmii interface. If the user specificies phy-mode sgmii, then
use the gmac-config/device node to ensure the mux is configured
correctly.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
This patch adds support for Globalscale ESPRESSObin-Ultra. Device uses
the same Armada-3720 SoC with extended hardware support.
- SoC: Armada-3720
- RAM: 1 GB DDR4
- Flash: 4MB SPI NOR (mx25u3235f) + 8 GB eMMC
- Ethernet: Topaz 6341 88e6341 (4x GB LAN + 1x WAN with 30W PoE)
- WiFI: 2x2 802.11ac Wi-Fi marvell (88w8997 PCIe+USB)
- 1x USB 2.0 port
- 1x USB 3.0 port
- 1x microSD slot
- 1x mini-PCIe slot (USB [with nano-sim slot])
- 1x mini-USB debug UART
- 1x RTC Clock and battery
- 1x reset button
- 1x power button
- 4x LED (RGBY)
- Optional 1x M.2 2280 slot
** Installation **
Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a53_musl/linux-mvebu_cortexa53/
linux-5.4.65/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dtb
bin/targets/mvebu/cortexa53/
$ in.tftpd -L -s bin/targets/mvebu/cortexa53/
Connect to the device UART via microUSB port on the back side and power on the device.
Power on the device and hit any key to stop the autoboot.
Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device
Ping server to confirm network is working:
$ ping $serverip
Using neta@30000 device
host 192.168.1.15 is alive
Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-initramfs-kernel.bin
$ tftpboot $fdt_addr_r armada-3720-espressobin-ultra.dtb
Set the console and boot the image:
$ setenv bootargs $console
$ booti $kernel_addr_r - $fdt_addr_r
Once the initramfs is booted, transfer openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz
to /tmp dir on the device.
Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img of=/dev/mmcblk0 && sync
Reboot the device.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
This patch add missing support of SC16IS740 serial controller, installed
on LS1012A-FRDM board.
It was required to change RCW bits, because SPI was disabled by default.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This will make developing process easier, because dtb will be included
into image.
Not need to enable initramfs image by default.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Currently sfp_select_interface() return the fastest interface that
the sfp modules supports even if the phy don't support that mode.
For example an GPON module that support both 2500basex and 1000basex.
Currently sfp_select_interface() picks 2500basex instead of 1000basex.
So limit the interfaces which both sides supports before calling
sfp_select_interface() or return an error if we don't have match.
Reviewed-by: John Thomson <git@johnthomson.fastmail.com.au>
Tested-by: Braihan Cantera <bcanterac@gmail.com> [MikroTik RB760iGS + Nokia G-010S-A 3FE46541AA SFP]
Tested-by: John Thomson <git@johnthomson.fastmail.com.au> [Mikrotik rb760igs + SFP SM/LC, SFP base1000T, SFP+ passive DAC]
Signed-off-by: René van Dorst <opensource@vdorst.com>
Some devices (especially QCA ones) are already using hardcoded partition
names with colons in it. The OpenMesh A62 for example provides following
mtd relevant information via cmdline:
root=31:11 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(custom),64k(0:KEYS),0x002b0000(kernel),0x00c80000(rootfs),15552k(inactive) rootfsname=rootfs rootwait
The change to split only on the last colon between mtd-id and partitions
will cause newpart to see following string for the first partition:
KEYS),0x002b0000(kernel),0x00c80000(rootfs),15552k(inactive)
Such a partition list cannot be parsed and thus the device fails to boot.
Avoid this behavior by making sure that the start of the first part-name
("(") will also be the last byte the mtd-id split algorithm is using for
its colon search.
Fixes: d6a9a92e32 ("kernel: bump 5.4 to 5.4.69")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The OpenMesh related files were not updated since a while and the new
coding style requirements weren't integrated. This can cause problems
for new devices when an author uses these files as starting point.
* use SPDX-License-Identifiers instead of full license texts
* drop linux,default-trigger with value default-off for LEDs
* led nodes with label "abc:xyz" should have name "xyz_abc"
* led DT labels for "xyz_abc" should be "led_xyz_abc"
* "m25p80@0" flash node should be renamed to "flash@0"
* drop unnecessary empty lines
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[minor commit title and message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
You can flash via tftp recovery:
- serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24
- connect to any ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button
Flashing via OEM web interface does not work.
LTE module does not support DHCP so it must be configured via QMI.
Hardware Specification (v4.0 EU):
- SoC: MT7628NN
- Flash: Winbond W25Q64JVS (8MiB)
- RAM: ESMT M14D5121632A (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 1NIC (4x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 9V 0.85A
Signed-off-by: Filip Moc <lede@moc6.cz>
The ImageBuilder downloads pre-built packages and adds them to images.
This process uses `opkg` which has the capability to verify package list
signatures via `usign`, as enabled per default on running OpenWrt
devices.
Until now this was disabled for ImageBuilders because neither the `opkg`
keys nor the `opkg-add` script was present during first packagelist
update.
To harden the ImageBuilder against *drive-by-download-attacks* both keys
and verification script are added to the ImageBuilder allowing `opkg` to
verify downloaded package indices.
This commit adds `opkg-add` to the ImageBuilder scripts folder. The keys
folder is added to ImageBuilder $TOPDIR to have an obvious place for users to
store their own keys. The `option check_signature` is appended to the
repositories.conf file. All of the above only happens if the Buildbot
runs with the SIGNATURE_CHECK option.
The keys stored in the ImageBuilder keys/ are the same as included in
the openwrt-keyring package. To avoid the chicken-egg problem of
downloading and verifying a package, containing signing keys, the keys
are added during the ImageBuilder generation. They are same as in
shipped images (stored at `/etc/opkg/keys/`).
To allow a local package feed in which the user can add additional
packages, a local set of `usign` and `ucert` keys is generated, same as
building OpenWrt from source. The private key signs the local repository
inside the packages/ folder. The local public key is added to the keys/
folder to be considered by `opkg` when updating repositories. This way a
local package feed can be modified while requiring `opkg` to check
signatures for remote feed, making HTTPS optional.
The new option `ADD_LOCAL_KEY` allows to add the local key inside the
created images, adding the advantage that sysupgrades can validate the
ImageBuilders local key.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This patch adds support for the WiFi Pineapple Mark 7, a wireless
penetration testing tool.
Specifications:
* SoC: MediaTek MT7628 (580MHz)
* RAM: 256MiB (DDR2)
* Storage 1: 32MiB NOR (SPI)
* Storage 2: 2GB eMMC
* Wireless 1: 802.11b/g/n 2.4GHz (Built In)
* Wireless 2: 802.11b/g/n 2.4GHz (MT7601)
* Wireless 3: 802.11b/g/n 2.4GHz (MT7601)
* USB: 1x USB Type-A 2.0 Host Port
* Ethernet: 1x USB Type-C AX88772C Ethernet
* UART: 57600 8N1 on PCB
* Inputs: 1x Reset Button
* Outputs: 1x RGB LED
* FCCID: 2AA52MK7
Flash Instructions:
Original firmware is based on OpenWRT.
Use sysupgrade via SSH to flash.
Signed-off-by: Marc Egerton <foxtrot@realloc.me>
[pepe2k@gmail.com: set only required/used gpio groups to gpio function]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
New batches of the R36A board series might no longer keep separated
Ethernet MAC addresses stored in flash. Use same approach as on the
N2Q and calculate Ethernet MACs from WLAN one which is kept in ART.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network Pi-WiFi4 is a Qualcomm QCA9531 v2 based, high-power 802.11n
WiFi board in Raspberry Pi 3B shape, equipped with 1x FE and 4x USB 2.0.
Specifications:
- Qualcomm/Atheros QCA9531 v2
- 650/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16+ MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz Wi-Fi with Qorvo RFFM8228P FEM
- 2x IPEX/U.FL connectors on PCB
- 4x USB 2.0 Type-A
- Genesys Logic GL850G 4-port USB HUB
- USB power is controlled by GPIO
- 5x LED (3x on PCB, 2x in RJ45, 4x driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, enabled by default)
- 1x micro USB Type-B for power and system console (Holtek HT42B534)
- UART and GPIO (8-pin, 1.27 mm pitch) header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The Xiaomi Mi Router 4A Gigabit model has a race condition on bootup
causing the SQUASHFS data errors to appear and create a bootloop
scenario.
Adding the m25p,fast-read property resolves this issue.
Suggested-by: David Bentham <db260179@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
CPU: Atheros AR9342 rev 3 SoC
RAM: 64 MB DDR2
Flash: 16 MB NOR SPI
WLAN 2.4GHz: Atheros AR9342 v3 (ath9k)
WLAN 5.0GHz: QCA988X
Ports: 2x GbE
Flashing procedure is identical to other ubnt devices.
https://openwrt.org/toh/ubiquiti/common
Flashing through factory firmware
1. Ensure firmware version v8.7.0 is installed.
Up/downgrade to this exact version.
2. Patch fwupdate.real binary using
`hexdump -Cv /bin/ubntbox | sed 's/14 40 fe 27/00 00 00 00/g' | \
hexdump -R > /tmp/fwupdate.real`
3. Make the patched fwupdate.real binary executable using
`chmod +x /tmp/fwupdate.real`
4. Copy the squashfs factory image to /tmp on the device
5. Flash OpenWrt using `/tmp/fwupdate.real -m <squashfs-factory image>`
6. Wait for the device to reboot
(copied from Ubiquiti NanoBeam AC and modified)
To keep it consistent, we will add the gen1 variant to
the nanobeam ac gen1.
Signed-off-by: Nick Hainke <vincent@systemli.org>
This adds a missing ";;" in the switch-case in 11-ath10k-caldata.
Fixes: 4d36569b9c ("ath79: fix ath10k caldata extraction on some
D-Link DIR-842 C3 devices")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
According to forum threads [0][1] and a report on IRC by Doc-Saintly
some of those boards have calibration data in a different place. Only
one alternative location is known.
Without proper board calibration data (board.bin having all 0xff bytes)
ath10k firmware still tries to load but crashes on startup with a
confusing error message.
If you're applying this patch manually on your device do not forget to
remove /lib/firmware/ath10k/pre-cal-pci-0000:00:00.0.bin and reboot to
force caldata re-extraction.
[0] https://forum.openwrt.org/t/support-for-d-link-dir842-rev-c3/41654
[1] https://forum.openwrt.org/t/d-link-dir-842-cant-access-firmware-upload-form/65454
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
All targets that used mvsw61xx have switched to upstream mv88e6xxx DSA
driver, so it can be removed.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
mediatek frequently had mixed indent (tabs vs. spaces) in DTS files
and DTS file kernel patches (probably due to careless copy/paste).
The harmonizes these cases to tabs-only, as usual for DTS(I).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Both bcm2709 and bcm2710 firmware can run on the same RaspberryPi
models, varying however in 32 and 64 Bit architectures. The model name
alone does not include the architecture information, which becomes
problematic if looking at a overview that only contains the names. By
adding a variant it is possible to tell the architecture.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This pci@40000000 node from upstream was dropped when the device
was converted from local DTS(I) files to kernel patches in [1] to
ensure that change was purely cosmetic.
However, the DK04.1 has a PCI-E slot by default, so let's keep
(i.e. not remove) the kernel definition now.
[1] c4beac9ea2 ("ipq40xx: use upstream DTS files for IPQ4019/AP-DK04.1")
Suggested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
A lot of patches are outdated versions of upstreamed patches and
drivers.
So lets pull in the upstreamed patches and reorder remaining ones.
This drops the unnecessary 721-dts-ipq4019-add-ethernet-essedma-node.patch
which adds nodes for not yet in OpenWrt IPQESS driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[do not touch 902-dts-ipq4019-ap-dk04.1.patch here]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Define wildcard patterns for filtering in target/linux/generic/config-filter
Preparation for supporting newer kernels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MikroTik recently changed again the way they store wlan calibration data
on devices. Prior to this change, ERD calibration data for all available
radios was stored within a single identifier node ("tag" in RouterBoot
parlance).
Recent devices have been seen with calibration (and BDF) data stored in
separate identifiers within LZOR packing for each radio: this patch
addresses this by:
1) ensuring that both variants are properly supported,
2) preserving backward compatibility with existing data consumers,
3) allowing for more than 2 calibration blobs to be exposed via sysfs.
Specifically, before this patch, the driver would provide a single sysfs
file named /sys/firmware/mikrotik/hard_config/wlan_data that contained
whatever calibration data found on the device's flash. After this patch,
when executed on a device that uses the old style storage, this behavior
is unchanged, but when executed on a device that uses new style storage
(for either traditional "ERD" packing or "LZOR" packing), the driver
replaces that single file with a folder containing one or more files
each containing the data encoded within individual identifiers.
As far as OpenWRT is concerned, this means that for devices which are
known to exist with both styles of data storage, a suitable hotplug stub
could look like this for e.g. the second radio:
wdata="/sys/firmware/mikrotik/hard_config/wlan_data"
( [ -f "$wdata" ] && caldata_sysfsload_from_file "$wdata" 0x8000 0x2f20 ) || \
( [ -d "$wdata" ] && caldata_sysfsload_from_file "$wdata/data_2" 0x0 0x2f20 )
This patch has been tested with LZOR old and new style packing on ipq4019,
and with old style on ath79.
Tested-by: John Thomson <git@johnthomson.fastmail.com.au>
Tested-by: Шебанов Алексей <admin@ublaze.ru>
Tested-by: Alen Opačić <subixonfire@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: Robert Marko <robimarko@gmail.com>
CONFIG_EFI_VARS has been disabled in
64bit x86 target in 2018 by the following commit
b0a51dab8c
the same reasons apply to Generic target, so
now it's disabled here too.
Leaving it enabled is also blocking compile as
a new symbol was added
EFI_CUSTOM_SSDT_OVERLAYS
that depends from CONFIG_EFI_VARS
and the build system stops and waits for
user input on what to do about it.
The Legacy and Geode targets never
had any EFI_xxx configs enabled so they
don't have this issue
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
This adds support for RTL839x SoCs in the ethernet and switch
drivers of the rtl838x architecture.
Reviewed-by: Andreas Oberritter <obi@saftware.de>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This device has previously been supported by the image
for Xiaomi Mi Router 3G v2. Since this is not obvious, the
4A is marketed as a new major revision and it also seems to
have a different bootloader, this will be both more tidy and
more helpful for the users.
Apart from that, note that there also is a 100M version of
the device that uses mt7628 platform, so a specifically named
image will also prevent confusion in this area.
Specifications:
- SoC: MediaTek MT7621
- Flash: 16 MiB NOR SPI
- RAM: 128 MiB DDR3
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable "power" LED (two-coloured, yellow/blue)
Non-programmable "internet" LED (shows WAN activity)
- Buttons: Reset
Installation:
Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on".
Vendor firmware won't accept any serial input until "uart_en" is
set to "1".
Using the https://github.com/acecilia/OpenWRTInvasion exploit you
can gain access to shell to enable these options:
To enable uart keyboard actions - 'nvram set uart_en=1'
To make uboot delay boot work - 'nvram set boot_wait=on'
Set boot delay to 5 - 'nvram set bootdelay=5'
Then run 'nvram commit' to make the changes permanent.
Once in the shell (following the OpenWRTInvasion instructions) you
can then run the following to flash OpenWrt and then reboot:
'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin
--output firmware.bin; mtd -e OS1 -r write firmware.bin OS1'
Suggested-by: David Bentham <db260179@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
E600G v2 based on Qualcomm/Atheros QCA9531
Specification:
- 650/600/200 MHz (CPU/DDR/AHB)
- 128/64 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz
- 2 x 10/100 Mbps Ethernet(RJ45)
- 1 x MiniPCI-e
- 1 x SIM (3G/4G)
- 5 x LED , 1 x Button(SW2-Reset Buttun), 1 x power input
- UART(J100) header on PCB(115200 8N1)
E600GAC v2 based on Qualcomm/Atheros QCA9531 + QCA9887
Specification:
- 650/600/200 MHz (CPU/DDR/AHB)
- 128/64 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz
- 1T1R 5 GHz
- 2 x 10/100 Mbps Ethernet(RJ45)
- 6 x LED (one three-color led), 2 x Button(SW2-Reset Buttun),1 x power input
- UART (J100)header on PCB(115200 8N1)
Flash instruction:
1.Using tftp mode with UART connection and original OpenWrt image
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "openwrt-ath79-generic-xxx-squashfs-sysupgrade.bin"
to "firmware.bin" and place it in tftp server directory.
- Connect PC with one of LAN ports, power up the router and press
key "Enter" to access U-Boot CLI.
- Use the following commands to update the device to OpenWrt:
run lfw
- After that the device will reboot and boot to OpenWrt.
- Wait until all LEDs stops flashing and use the router.
2.Using httpd mode with Web UI connection and original OpenWrt image
- Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
- Connect PC with one of LAN ports,press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
leds flashing.
- Open your browser and enter 192.168.1.1,You will see the upgrade
interface, select "openwrt-ath79-generic-xxx-squashfs-
sysupgrade.bin" and click the upgrade button.
- After that the device will reboot and boot to OpenWrt.
- Wait until all LEDs stops flashing and use the router.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[rearrange in generic.mk, fix one case in 04_led_migration, update
commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The file lacks executable permissions, which makes it not being applied
during the first boot.
While at it, drop unneeded include.
Signed-off-by: Piotr Jurkiewicz <piotr.jerzy.jurkiewicz@gmail.com>
[do not touch board name handling, update commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for D-Link DIR-2640 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (blue/orange), Internet (blue/orange), WiFi 2.4G (blue),
WiFi 5G (blue), USB 3.0 (blue), USB 2.0 (blue)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:a7 (label)
wan factory 0xe006 *:aa
2.4 factory 0xe000 +1 *:a8
5.0 factory 0xe000 +2 *:a9
Seems like vendor didn't replace the dummy entries in the calibration data.
Signed-off-by: James McGuire <jamesm51@gmail.com>
[fix device definition title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tomasz Maciej Nowak
Adrian Schmutzler