This is first step in migrating to a generic i.MX target which in the
next steps will also get divided into arch-specific subtargets.
In the result, this will make it possible to support, within a single
target, also other modern NXP i.MX families, like the i.MX 7, i.MX 8
or recently introduced i.MX 9.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This is a minor extension of the commit 26ae69fd03 ("imx6: refresh
kernel config with 5.10 symbols"), with correct and full disable of
the Arm Cortex-A7 based i.MX 6UL and 6UL{L,Z} families support and
re-enable of the Cortex-A9 based i.MX 6L{S,X}.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
U-Boot for the Gateworks Ventana includes filename of the boot script in
the default/embedded environment (see 'include/configs/gw_ventana.h' in
the U-Boot sources).
This restores the old boot script filename ('6x_bootscript-ventana'),
making Ventana boards boot again.
Fixes: 8dba71dd33 ("imx6: image: drop BOOT_SCRIPT and fix DEVICE_NAME")
Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Netgear R6100 is a dual-band Wi-Fi 5 (AC1200) router based on Qualcomm
Atheros (AR9344 + QCA9882) platform. Support for this device was first
introduced in 15f6f67d18 (ar71xx). FCC ID: PY312400225.
Specifications:
- Atheros AR9344 (560 MHz)
- 128 MB of RAM (DDR2)
- 128 MB of flash (parallel NAND)
- 2T2R 2.4 GHz Wi-Fi (AR9344)
- 2T2R 5 GHz Wi-Fi (QCA9882)
- 5x 10/100 Mbps Ethernet (AR9344)
- 4x internal antenna
- 1x USB 2.0 (GPIO-controlled power)
- 6x LED, 3x button (reset, Wi-Fi, WPS)
- UART (4-pin, 2.54 mm pitch) header on PCB
- 1x mechanical power switch
- DC jack for main power input (12 V)
WARNING: sysupgrade from older stable releases is not possible, fresh
installation (via vendor's GUI or TFTP based recovery) is required.
Reason for that is increased kernel partition size.
Installation:
Use the 'factory' image under vendor's GUI or via TFTP U-Boot recovery.
You can use the 'nmrpflash' tool at a boot time, before kernel is loaded
or start it manually by pressing the 'reset' button for ~20 seconds from
powering up the device (U-Boot will start TFTP server on 192.168.1.1,
use TFTP client to send the image).
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
CONFIG_COMPAT_32BIT_TIME is a new symbol and has to be set to avoid:
Provide system calls for 32-bit time_t (COMPAT_32BIT_TIME) [N/y/?] (NEW)
CONFIG_RELOCATABLE needs to be enabled to make kernel start booting.
That raises a question: do we really need CONFIG_EXPERT=y ?
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The boot arguments are copied into the device tree by the boot loader
and taken from the device tree by the kernel.
The code which takes the boot arguments from the different sources was
reworked with kernel 5.5.
We have to activate CONFIG_MIPS_CMDLINE_DTB_EXTEND to take the boot
arguments from the device tree.
This makes the system boot on the board again.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Make the patches apply on kernel 5.10 and refresh the patches and the
kernel configuration on top of kernel 5.10.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The pistachio U-Boot expects a default configuration with the name
config@1 in the FIT image. The default was changed in OpenWrt some
months ago.
This makes the board boot again.
Fixes: 9f714398e0 ("build: use config-1 instead of config@1 as default")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It relies on a custom ax_code_coverage.m4 file included with strace.
Unfortunately, this conflicts with the one included with
autoconf-macros. Instead of creating a huge patch to fix it, just remove
the variable as code coverage is not used here.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
I had quite a hard time to understand what the change to net/core/dev.c
is supposed to do.
Simplify the change by returning NETDEV_TX_OK in case a eth_mangle_tx
callback was set but returned NULL instead of setting the return value
in the else branch.
Signed-off-by: Mathias Kresin <dev@kresin.me>
ar8216 switches have a hardware bug, which renders normal 802.1q support
unusable. Packet mangling is required to fix up the vlan for incoming
packets.
The patch was ommited at the time kernel 5.10 support was added but is
still required for ar8216 switches.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add the latest default Kernel for testing. This step is required to keep
UML in tree for the next release.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The UML target been outdated for a long time. Instead of just carrying
unmaintained code we should build it again and allow people and CIs to
use it for testing.
This commit removes the `source-only` feature which disables building.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This step drops support host build systems other than x86/64 to allow
two Kernel configuration in parallel. With this commit the setup follow
the config style of all other targets.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The current `uml` README is terribly outdated and non of the examples
work by default. Fix that and while at it convert it to Markdown.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The empty executable is causing problems with meson builds, due to the
error: OSError: [Errno 8] Exec format error: 'ldconfig'
This patch changes the empty ldconfig stub to symlink to /bin/true to
work around this issue.
Fixes: FS#4117
Fixes: 3bd31cc4d2 ("tools/meson: update to 0.60.0")
Signed-off-by: Damien Mascord <tusker@tusker.org>
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # Tested on Debian 11
Tested-By: Lucian Cristian <lucian.cristian@gmail.com>
Tested-By: Baptiste Jonglez <git@bitsofnetworks.org>
Cc: Rosen Penev <rosenp@gmail.com>
Build the tc-mod-iptables before the tc-tiny and tc-full packages.
This avoids unnecessary package rebuild when calling make back to back.
Before this change, tc-mod-iptables will be built after the main tc
binary packages.
Both tc-tiny and tc-full depend on tc-mod-ipables. If make is called
after the packages are already built, it will check the timestamps of
both packages, and will rebuild the main binaries, since the module
package will be newer than the tc package.
Calling BuildPackage,mod-iptables first ensures that its variant gets
built before the other packages' variants.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Set the different libf2fs packages's VARIANT, so that the right settings
will be used by each different variant, if they are both being built.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Package hostapd-common is a dependency of every other package defined in
hostpad Makefile. It is currently built next to the bottom of that
Makefile's package list.
If you run make back to back, then check-compile will compare the
hostapd-common timestamp to the variant being compiled, to decide if the
varint needs to be rebuilt or not. Since the hostapd-conf package is
built towards the end of the list, it will be newer than most of the
variants, causing unnecessary package rebuilds.
Move it to the top, so that its timestamp will be older than dependent
packages, avoiding unnecessary rebuild of every selected variant.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
If a Makefile defines some packages with VARIANT set, and others without
it, the latter will be built once for every different VARIANT set, each
build trumping the previous one.
Avoid rebuilds by only building unnamed variant packages when the first
variant is built.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
The $(LINUX_DIR)/.config timesptamp changes between runs of
make target/compile and make target/install (which builds the image).
Kernel-dependent packages and out of tree modules are built in between
those runs, and they check the .config timestamp to decide if they need
to be rebuilt.
Save the target/compile .config to use its timestamp if the file does
not change between runs. That way the subsequent kernel packages are
not unnecessarily rebuilt when you run 'make' back to back.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
4e19cbc5533: [download: handle possibly invalid local tarballs] added a
FORCE rule to downloaded files, so that they will be always checked by
download.pl.
As a side-effect, check-compile will fail, forcing unnecessary package
rebuilds.
The check-compile.txt log shows (for libxml2 for example):
Considering target file '.../dl/libxml2-2.9.12.tar.gz'.
...
prerequisite 'FORCE' of target '.../dl/libxml2-2.9.12.tar.gz' does
not exist.
Must remake target '.../dl/libxml2-2.9.12.tar.gz'.
...
Giving up on target file '...libxml2-2.9.12/.prepared_...'.
Giving up on target file '...libxml2-2.9.12/.configured_...'.
Giving up on target file '...libxml2-2.9.12/.built'.
Giving up on target file '...stamp/.libxml2_installed'.
Giving up on target file '.compile'.
Then the package is rebuilt even if it is not otherwise needed.
To fix this, instead of always forcing the download target to be remade,
check its hash first: if it matches, then the FORCE is not added.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Don't patch the kernel to expose the partition name in sysfs as it is
already exposed via 'uevent'.
All previous users have been converted to use 'uevent', so we can
safely drop the custom patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
19fd7fc libfstools: make sure file is closed on error
d390744 libfstools: use uevent instead of relying on custom kernel patch
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
find_mmc_part provides a better alternative and all users of
get_partition_by_name have been removed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use find_mmc_part instead of previously introduced
get_partition_by_name which requires a custom kernel patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use find_mmc_part instead of previously introduced
get_partition_by_name which requires a custom kernel patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some devices got more than one mmc device.
Allow specifying the root device as 2nd parameter of find_mmc_part so
scripts can avoid matching irrelevant partitions on wrong mmc device.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
qosify is simple daemon for setting up and managing CAKE along with a custom
eBPF based classifier that sets DSCP fields of packets.
It is configured via UCI and it supports the following features:
- simple TCP/UDP port based mapping
- IP address based mapping
- priority boosting based on average packet size
- bulk flow detection based on number of packets per second
- dynamically add IP entries with timeout
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to genererate suitable kernel headers, a 5.10 kernel tree is
prepared with a default config for mips. The arch is forced to mips in
order to avoid issues with inline asm on various architectures in a way
that doesn't involve relying on the host toolchain/headers.
It also has the advantage of supporting both endian types
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Commit a2fcd3900c ("dnsmasq: improve init script") broke the existing
handling for hosts_dir. Remove the redundant mount again to fix it.
Reported-by: Hartmut Birr <e9hack@gmail.com>
Fixes: a2fcd3900c ("dnsmasq: improve init script")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
b743a331421d ubusd: log ACL init errors
2099bb3ad997 libubus: use list_empty/list_first_entry in ubus_process_pending_msg
ef038488edc3 libubus: process pending messages in data handler if stack depth is 0
a72457b61df0 libubus: increase stack depth for processing obj msgs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The Netgear SRS60 and SRR60 (sold together as SRK60) are two almost
identical AC3000 routers. The SRR60 has one port labeled as wan while
the SRS60 not. The RBR50 and RBS50 (sold together as RBK50) have a
different external shape but they have an USB 2.0 port on the back.
This patch has been tested only on SRS60 and RBR50, but should work
on SRR60 and RBS50.
Hardware
--------
SoC: Qualcomm IPQ4019 (717 MHz, 4 cores 4 threads)
RAM: 512MB DDR3
FLASH: 4GB EMMC
ETH:
- 3x 10/100/1000 Mbps Ethernet
- 1x 10/100/1000 Mbps Ethernet (WAN)
WIFI:
- 2.4GHz: 1x IPQ4019 (2x2:2)
- 5GHz: 1x IPQ4019 (2x2:2)
- 5GHz: 1x QCA9984 (4x4:4)
- 6 internal antennas
BTN:
- 1x Reset button
- 1x Sync button
- 1x ON/OFF button
LEDS:
- 8 leds controlled by TLC59208F (they can be switched on/off
independendently but the color can by changed by GPIOs)
- 1x Red led (Power)
- 1x Green led (Power)
UART:
- 115200-8-N-1
Everything works correctly.
Installation
------------
These routers have a dual partition system. However this firmware works
only on boot partition 1 and the OEM web interface will always flash on
the partition currently not booted.
The following steps will use the SRS60 firmware, but you have to chose
the right firmware for your router.
There are 2 ways to install Openwrt the first time:
1) Using NMRPflash
1. Download nmrpflash (https://github.com/jclehner/nmrpflash)
2. Put the openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img
file in the same folder of the nmrpflash executable
3. Connect your pc to the router using the port near the power button.
4. Run "nmrpflash -i XXX -f openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img".
Replace XXX with your network interface (can be identified by
running "nmrpflash -L")
5. Power on the router and wait for the flash to complete. After about
a minute the router should boot directly to Openwrt. If nothing
happens try to reboot the router. If you have problems flashing
try to set "10.164.183.253" as your computer IP address
2) Without NMRPflash
The OEM web interface will always flash on the partition currently not
booted, so to flash OpenWrt for the first time you have to switch to
boot partition 2 and then flash the factory image directly from the OEM
web interface.
To switch on partition 2 you have to enable telnet first:
1. Go to http://192.168.1.250/debug.htm and check "Enable Telnet".
2. Connect through telent ("telnet 192.168.1.250") and login using
admin/password.
To read the current boot_part:
artmtd -r boot_part
To write the new boot_part:
artmtd -w boot_part 02
Then reboot the router and then check again the current booted
partition
Now that you are on boot partition 2 you can flash the factory Openwrt
image directly from the OEM web interface.
Restore OEM Firmware
--------------------
1. Download the stock firmware from official netgear support.
2. Follow the nmrpflash procedure like above, using the official
Netgear firmware (for example SRS60-V2.2.1.210.img)
nmrpflash -i XXX -f SRS60-V2.2.1.210.img
Notes
-----
1) You can check and edit the boot partition in the Uboot shell using
the UART connection.
"boot_partition_show" shows the current boot partition
"boot_partition_set 1" sets the current boot partition to 1
2) Router mac addresses:
LAN XX:XX:XX:XX:XX:69
WAN XX:XX:XX:XX:XX:6a
WIFI 2G XX:XX:XX:XX:XX:69
WIFI 5G XX:XX:XX:XX:XX:6b
WIFI 5G (2nd) XX:XX:XX:XX:XX:6c
LABEL XX:XX:XX:XX:XX:69
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
[added 5.10 changes for 901-arm-boot-add-dts-files.patch, moved
sysupgrade mmc.sh to here and renamed it, various dtsi changes]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Piotr Dymacz