Commit Graph

3 Commits

Author SHA1 Message Date
Sungbo Eo 37753f34ac ramips: add support for ipTIME AX2004M
ipTIME AX2004M is an 802.11ax (Wi-Fi 6) router, based on MediaTek
MT7621A.

Specifications:
* SoC: MT7621A
* RAM: 256 MiB
* Flash: NAND 128 MiB
* Wi-Fi:
  * MT7915D: 2.4/5 GHz (DBDC)
* Ethernet: 5x 1GbE
  * Switch: SoC built-in
* USB: 1x 3.0
* UART: J4 (115200 baud)
  * Pinout: [3V3] (TXD) (RXD) (GND)

MAC addresses:

| interface |    MAC address    |     source     | comment
|-----------|-------------------|----------------|---------
|       LAN | 58:xx:xx:00:xx:9B |                | [1]
|       WAN | 58:xx:xx:00:xx:99 |                |
|   WLAN 2G | 58:xx:xx:00:xx:98 | factory 0x4    |
|   WLAN 5G | 5A:xx:xx:40:xx:98 |                |
|           | 58:xx:xx:00:xx:98 | config ethaddr |

[1] Used in this patch as WLAN 5G MAC address with the local bit set

Load addresses:
* stock
  * 0x80010000: FIT image
  * 0x81001000: kernel image -> entry
* OpenWrt
  * 0x80010000: FIT image
  * 0x82000000: uncompressed kernel+relocate image
  * 0x80001000: relocated kernel image -> entry

Notes:
* This device has a dual-boot partition scheme, but this firmware works
  only on boot partition 1. The stock web interface will flash only on the
  inactive boot partition, but the recovery web page will always flash on
  boot partition 1.

Installation via recovery mode:
1.  Press reset button, power up the device, wait >10s for CPU LED
    to stop blinking.
2.  Upload recovery image through the recovery web page at 192.168.0.1.

Revert to stock firmware:
1.  Install stock image via recovery mode.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-02-11 22:30:04 +09:00
Stijn Tintel cd6a6e3030 Revert "ramips: add support for ipTIME AX2004M"
Commit f4a79148f8 ("ramips: add support for ipTIME AX2004M") seems to
leak KERNEL_LOADADDR 0x82000000 to other devices, causing the to no
longer boot. The leak is visible in u-boot:

   Using 'config-1' configuration
   Trying 'kernel-1' kernel subimage
     Description:  MIPS OpenWrt Linux-5.10.92
     Type:         Kernel Image
     Compression:  lzma compressed
     Data Start:   0x840000e4
     Data Size:    10750165 Bytes = 10.3 MiB
     Architecture: MIPS
     OS:           Linux
     Load Address: 0x82000000
     Entry Point:  0x82000000

Normally, it should look like this:

   Using 'config-1' configuration
   Trying 'kernel-1' kernel subimage
     Description:  MIPS OpenWrt Linux-5.10.92
     Type:         Kernel Image
     Compression:  lzma compressed
     Data Start:   0xbfca00e4
     Data Size:    2652547 Bytes = 2.5 MiB
     Architecture: MIPS
     OS:           Linux
     Load Address: 0x80001000
     Entry Point:  0x80001000

Revert the commit to avoid more people soft-bricking their devices.

This reverts commit f4a79148f8.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-02-01 21:35:15 +02:00
Sungbo Eo f4a79148f8 ramips: add support for ipTIME AX2004M
ipTIME AX2004M is an 802.11ax (Wi-Fi 6) router, based on MediaTek
MT7621A.

Specification:
* SoC: MT7621A
* RAM: 256 MiB
* Flash: NAND 128 MiB
* Wi-Fi:
  * MT7915D: 2.4/5 GHz (DBDC)
* Ethernet: 5x 1GbE
  * Switch: SoC built-in
* USB: 1x 3.0
* UART: J4 (115200 baud)
  * Pinout: [3V3] (TXD) (RXD) (GND)

MAC address:

| interface |        MAC        |     source     | comment
|-----------|-------------------|----------------|---------
|       LAN | 58:XX:XX:00:XX:9B |                | [1]
|       WAN | 58:XX:XX:00:XX:99 |                |
|   WLAN 2G | 58:XX:XX:00:XX:98 | factory 0x4    |
|   WLAN 5G | 5A:XX:XX:40:XX:98 |                |
|           |                   |                |
|           | 58:XX:XX:00:XX:98 | config ethaddr |

[1] Used in this patch as WLAN 5G MAC address with the local bit set

Load address:
* stock
  * 0x80010000: FIT image
  * 0x81001000: kernel image -> entry
* OpenWrt
  * 0x80010000: FIT image
  * 0x82000000: uncompressed kernel+relocate image
  * 0x80001000: relocated kernel image -> entry

Installation via **recovery** mode:
1.  Press reset button, power up the device, wait >10s for CPU LED
    to stop blinking.
2.  Upload recovery image through the recovery web page at 192.168.0.1.

Revert to stock firmware:
1.  Install stock image via recovery mode.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00