Allign dl_github_archieve.py to 8252511dc0
change. On supported system the sigid bit is applied to files and tar
archieve that on tar creation. This cause unreproducible tar for these
system and these bit should be dropped to produce reproducible tar.
Add the missing option following the command options used in other
scripts.
Fixes: 75ab064d2b ("build: download code from github using archive API")
Suggested-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 5f1758ef14)
Openwrt now supports only glibc and musl. Add support for musl and
rework the libc check to handle the new config flags and correctly
compile package basend on that.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 7be01fe13b)
Openwrt generate info.mk that contains the libc type. For probe_cc check
if the file exist and parse directly it for LIBC type.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 75311977f5)
Currently we never call probe_cc before config generation, this cause
the script to never actually detect the correct libc type.
Call probe_cc before config generation to correctl set the .config file.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit ddeabc75eb)
It can be useful to overwrite an already generated config.
Option are simply added at the end of the config and make defconfig
will overwrite the relevant option with the new one.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit f4dd18ca39)
The parsed prefix in print_config is wrong and this produce broken
generated .config that won't work with any external toolchain.
Currently the prefix from a CC of
'arm-openwrt-linux-muslgnueabi-gcc-12.1.0'
produce a prefix
'arm-openwrt-linux-muslgnueabi-gcc-'
This is wrong as the real prefix should be
'arm-openwrt-linux-muslgnueabi-'
This is probably caused by a change in how the toolchain is now handled
that now append also the gcc version. Probably in ancient days the
version wasn't part of the name and the prefix generation stripped the
'-gcc' instead of the gcc version.
Fix this and correctly strip the gcc version and the gcc suffix to
correctly call toolchain bins.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 53c293262f)
This only affects typos in comments or user-facing output.
Signed-off-by: Josh Soref <jsoref@users.noreply.github.com>
[only picks changes to scripts, drop "commandline" replacement,
fix case for "arbitrary", improve commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 08622de7d6)
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add a simple script to make it easier to install a prebuilt tools tar.
Currently it will be used by our tools container and kernel workflow on
github.
Simple script that take a tar that contains prebuilt host tools, extract
them and refresh the timestamps to skip recompilation of such host
tools.
By default it refresh timestamps of build_dir/host and
staging_dir/host/stamp.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 5428bdc2df)
Several users of wget for downloads (curl is not available in the
system) have reported broken download functionality:
wget --tries=5 --timeout=20 --output-document=- https://cdn.kernel.org/pub/linux/kernel/v5.x/linux-5.10.142.tar.xz
http://: Invalid host name.
Thats all happening due to '' was passed as an argument, which got later
expanded to http://.
In the context of a list constructor '' is not nothing, it is an empty
string element. So fix it by using () as it will yield "nothing" and
thus not introduce an empty string element.
Fixes: #10692
Fixes: 90c6e3aedf ("scripts: always check certificates")
Signed-off-by: Jo-Philipp Wich <jo@mein.io> [shellwords() -> ()]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 50a48faa1b)
When running build in verbose mode `make V=s` we can see a lot of
following warnings when curl is not available in the system:
Can't exec "curl": No such file or directory at scripts/download.pl line 77.
So lets fix it by redirecting of the stderr to null hole.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c836ca84e8)
Remove flags from wget and curl instructing them to ignore bad server
certificates. Although other mechanisms can protect against malicious
modifications of downloads, other vectors of attack may be available
to an adversary.
TLS certificate verification can be disabled by turning oof the
"Enable TLS certificate verification during package download" option
enabled by default in the "Global build settings" in "make menuconfig"
Signed-off-by: Josh Roys <roysjosh@gmail.com>
[ add additional info on how to disable this option ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [backport]
(cherry picked from commit 90c6e3aedf)
So it can serve as a standalone drop in replacement for xxd utility used
currently mostly in U-Boot packages with `xxd -i` mode which outputs C
include file style, with aim for byte to byte identical output, so the
eventual difference in the generated output is easily spottable.
Fixes: #10555
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jo-Philipp Wich <jo@mein.io> [perl-fu]
(cherry picked from commit 06e01e817e)
In order to make it more portable.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 8b278a76d9)
xxdi.pl is a Perl script that implements vim's 'xxd -i' mode so that
packages do not have to use all of vim just to get this functionality.
References: #10555
Source: 97a6bd5cee/xxdi.pl
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 2117d04a3a)
Both $(AUTORELEASE) and $(PKG_SRC_VERSION) (from luci.git) use the Git
log to determine releases and package timestamps.
Feeds are shallow cloned by default, resulting in an incomplete Git log
and therefore different local package versions than offered upstream.
This commits sets the default feeds to use `src-git-full` to solve that.
Add fixes from "2b1d92f: scripts/feeds: silence git warning by selecting
pull style" to `src-git-full`
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 7fae1e5677)
If the image generation doesn't add any profiles to the output the
*profile merge* will fail. To avoid that set an empty profile as
fallback.
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit fd0d9909bf)
Keep other profiles.json content if the data belongs to the current
build version.
Also useful for the ImageBuilder, which builds for a single model each
time. Without this commit the profiles.json would only contain the
latest build profile information.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
[improve commit message]
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit a463b96241)
Remove duplicate packages by running in `target/linux/` rather than
`target/linux/<target>/<subtarget>` and sort packages alphabetically.
Squash commit of:
7880a64848 build,json: 3rd fixup of default_packages
b36068d35d build,json: fixup fixup of arch_packages
1bf2b3fe90 build,json: fixup missing arch_packages
Signed-off-by: Paul Spooren <mail@aparcar.org>
Calling without the DUMP=1 argument causes the target specific Makefile
to be "included" again which adds the target specific packages twice,
once on the actual run and once included from `include/target.mk`.
This led to duplicate package entries, causing confusion in downstream
projects using the generated JSON files.
While at it, apply `black` style to Python script.
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 7f4c2b1a4f)
When building from a local branch based off the "openwrt-21.02" branch,
version computation is wrong, because the number of local commits is
computed against master. As a result, it wrongly counts *all* commits
since the beginning of the openwrt-21.02 branch as local commits.
The fix is to compare to the openwrt-21.02 branch instead, which gives the
expected result.
A similar change had been applied to the openwrt-19.07 branch:
891022918d ("scripts: getver.sh: fix version based on stable branch")
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
This reverts commit b12288fa69.
The patchelf approach is too fragile, and the only users of this have been
converted to make patching unnecessary
Leave the abi_version_str variable in place in rules.mk
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Preparation for supporting dynamic ABI versions that depend on the runtime
configuration. Read the suffix from the staging dir pkginfo version files.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This makes it possible to declare a package ABI_VERSION independent from the
upstream soname by setting PKG_ABI_VERSION in the package makefile.
The library filename is fixed up for files installed to packages and to the
staging dir. References to the original from executables within the same
package are also fixed up
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As multiple LICENSES are shipped and no longer just LICENSE, modify the
OpenWrt tree detection in checkpatch.pl.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Multiple sources are hosted on OpenWrts source server only. The source
URLs to point to the server vary based on different epochs in OpenWrts
history.
Replace all by @OPENWRT which is an "empty" mirror, therefore using the
fallback servers sources.cdn.openwrt.org and sources.openwrt.org.
Signed-off-by: Paul Spooren <mail@aparcar.org>
In case the default sources for a package fail use the CDN rather than
our own mirror. In case the CDN fails, fallback to our mirror.
Also remove mirror1 which isn't available anymore.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Since 4ee3cf2b5a profiles with alternative vendor names may appear
multiple times in `tmp/.targetinfo` or `.targetinfo` (for
ImageBuilders).
The `target-metadata.pl` script adds these profiles then twice to
`PROFILE_NAMES` and the ImageBuilder show the profile twice when running
`make info`.
This patch removes duplicate profile IDs and only adds them once to
`.profiles.mk`.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The recent 7f285d "scripts/feeds: warn when skipping core package
override" floods SDK output with warning of overwriting "linux" and
"toolchain" core packages. This should be ignored as these are not
regular packages added via feeds.
While at it slightly improve the warning string.
Signed-off-by: Paul Spooren <mail@aparcar.org>
clang's gcc emulation does the right thing with -print-file-name now,
drop the wrapper
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The qemustart script currently picks the ext4 filesystem rather than
squashfs, while the latter is default for nearly all OpenWrt targets.
Change the default behaviour of qemustart to be in line with the rest.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Device specifications:
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200
* GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE
* GPIO-LEDs for power (orange) and status (blue)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3at POE+
+ used as WAN interface
* 12V 2A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
* QCA IPQ4018
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200
* 3x GPIO-LEDs for status (cyan, purple, yellow)
* 1x GPIO-button (reset)
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio4:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio3:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3af/at POE(+)
+ used as WAN interface
* 12V/24V 1A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
* Qualcomm/Atheros QCA9533 v2
* 650/600/217 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash (mx25l12805d)
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4 GHz Wi-Fi
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ Label: Ethernet 1
+ 24V passive POE (mode B)
+ used as WAN interface
- eth1
+ Label: Ethernet 2
+ 802.3af POE
+ builtin switch port 2
+ used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The NOR flash rootfs images stored in a sysupgrade.tar must end with the
JFFS2 marker. Otherwise, devices like OpenMesh A42/A62 are not able to
calculate the md5sum of the fixed squashfs part and store it inside the
u-boot-env.
But the commit ee76bd11bb ("images: fix boot failures on NAND with small
sub pages") adds up to 1020 0x00 bytes after the 0xdead0de EOF marker. The
calculated md5sum will be wrong due do this change and u-boot will fail to
boot the newly flashed device with a message like:
Validating MD5Sum of 'vmlinux'...
Passed!
Validating MD5Sum of 'rootfs'...
Failed!
583a1b7b54b8601efa64ade42742459b != 8850ee812dfd7638e94083329d5d2781
Data validation failed!
and boot the old image again.
Since the original change should not change the behavior of NOR images,
just check for the deadc0de marker at the end of the squashfs-jffs2 image
do avoid the problematic behavior for these images.
Fixes: ee76bd11bb ("images: fix boot failures on NAND with small sub pages")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The rootfs is padded to the full block size by padjffs2 and a 4 byte magic
value ("deadc0de") is added to the end. On first boot, the JFFS2 is
replacing the "deadc0de" marker when the rootfs_data is initialized.
The static part of the rootfs is therefore $rootfs_size - 4 and not
$rootfs_size - 262144 - 4.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The padding and block alignment is handled by the image build script and
doesn't need to be duplicated in the fwupgrade.cfg build script.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Some images are created using different filesystems, most popular
squashfs and ext4. To allow downstream projects to distinguesh between
those, add the `filesystem` information to created json files.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The previous behavior prefered same feed for dependent packages as
initial package. This caused inconsitency in installation of packages.
The difference was if two feeds provide same package (different version)
there was different result if you executed install for that specific
version compared to install for package depending on it from different
feed.
This ensures that preferred feed is propagated without change and
selected feed is used only really for package it was selected for.
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
Otherwise, a n00b like myself can get quite confused when moving a
package from core to feeds, for example.
(Hint: one *really* needs to clear out the tmp/info/.packageinfo...
entries for the stale package, but '-f' works as well.)
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It seems like after a build the /dl dir seems to now contain a .hash
file for each source file due to inproper cleanup so fix it by removing
those intermediate files before leaving the download action.
Fixes: 4e19cbc553 ("download: handle possibly invalid local tarballs")
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Currently it's assumed, that already downloaded tarballs are always
fine, so no checksum checking is performed and the tarball is used even
if it might be corrupted.
From now on, we're going to always check the downloaded tarballs before
considering them valid.
Steps to reproduce:
1. Remove cached tarball
rm dl/libubox-2020-08-06-9e52171d.tar.xz
2. Download valid tarball again
make package/libubox/download
3. Invalidate the tarball
sed -i 's/PKG_MIRROR_HASH:=../PKG_MIRROR_HASH:=ff/' package/libs/libubox/Makefile
4. Now compile with corrupt tarball source
make package/libubox/{clean,compile}
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Silence the warning in git 2.27 about undefined fast-forward style
in git pull. Define "ff-only" as the style.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
As package size changes are a continuous topic on the mailing list this
scripts helps developers to compare their local package modifications
against latest upstream.
The script downloads the latest package indexes based on env variables
or the `.config` file. The script compares the actual installed size
(data.tar.gz) or the IPK package size.
An example output is found below:
```
user@dawn:~/src/openwrt/openwrt$ ./scripts/size_compare.sh
Compare packages of ath79/tiny/mips_24kc:
dropbear busybox iw ubus
Checking configuration difference
% Total % Received % Xferd Average Speed Time Time Time Current
Dload Upload Total Spent Left Speed
100 554 100 554 0 0 336 0 0:00:01 0:00:01 --:--:-- 336
--- start config diff ---
--- /tmp/config.DDjwVh-LOCAL 2020-11-23 09:08:28.913203068 -1000
+++ /tmp/config.DDjwVh-UPSTREAM 2020-11-23 09:08:36.369240887 -1000
@@ -1,5 +1,9 @@
+CONFIG_ALL_KMODS=y
+CONFIG_ALL_NONSHARED=y
CONFIG_AUTOREBUILD=y
+CONFIG_AUTOREMOVE=y
--- 8< ---
CONFIG_BINARY_FOLDER=""
+CONFIG_BUILDBOT=y
+CONFIG_TARGET_ALL_PROFILES=y
CONFIG_TARGET_ROOTFS_DIR=""
CONFIG_USE_SSTRIP=y
CONFIG_USE_UCLIBCXX=y
--- end config diff ---
Checking installed size
Fetching latest package indexes...
% Total % Received % Xferd Average Speed Time Time Time Current
Dload Upload Total Spent Left Speed
100 80634 100 80634 0 0 33499 0 0:00:02 0:00:02 --:--:-- 33485
% Total % Received % Xferd Average Speed Time Time Time Current
Dload Upload Total Spent Left Speed
100 54082 100 54082 0 0 24252 0 0:00:02 0:00:02 --:--:-- 24252
Comparing package sizes...
Change Local Remote Package
+271 51386 51115 base-files
+123 705241 705118 bnx2-firmware
+86 17209 17123 fstools
+22 47989 47967 procd
+21 208311 208290 busybox
+19 67181 67162 netifd
```
I plan to integrate this script into the CI so we have a summary how
sizes change over different architectures.
Signed-off-by: Paul Spooren <mail@aparcar.org>
With this commit, the download script will try downloading source files
using the filename instead of the url-filename in case the previous
download attempt using the url-filename failed.
This is required, as the OpenWrt sources mirrors serve files using the
filename files might be renamed to after downloading. If the original
mirror for a file where url-filename and filename do not match goes
down, the download failed prior to this patch.
Further improvement can be done by performing this only for the
OpenWrt sources mirrors.
Signed-off-by: David Bauer <mail@david-bauer.net>
Kernel has separated the structs that are reported to be const in
checkpatch.pl into a file of its own, const_structs.checkpatch.
This file has been missing after the recent update of checkpatch.pl,
leading to the following message:
No structs that should be const will be found - file
'/data/openwrt/scripts/const_structs.checkpatch': No such file
or directory
This commit adds the relevant file from v5.10-rc4.
Fixes: 086ee09bbc ("scripts: Update checkpatch.pl to 2020-06-11")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The kernel expects changes to MAINTAINERS for all removed or added
files, printing warnings like:
WARNING: added, moved or deleted file(s), does MAINTAINERS need updating?
#828:
deleted file mode 100644
Since this does not apply to "our" files in OpenWrt repo, this
warning should be disabled.
This can be achieved easiest by setting $reported_maintainer_file
to 1. While this is a hack that tricks the script into believing
the proper MAINTAINERS changes have been made, it's the easiest
solution as it does not require to touch any other code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Christian Marangi
Adrian Schmutzler