Commit Graph

15 Commits

Author SHA1 Message Date
Sven Eckelmann 78a5d25dca ar71xx: Skip more hashed blocks for OM2P(-HS) 64k variant
The OM2P(-HS)v4 got a variant which uses a slightly different flash. The
standard versions used a flash with 256KB blocks which is no longer
available. The replacement flash uses a flash with 64K blocks.

The padding for the image rootfs is already for 64K and 256K and thus can
be flashed on the device without any problems. Unfortunately, the
bootloader will check $rootfs_size (rounded down to the nearest 64k block)
minus 1x 64k. But it is now possible that the new JFFS2 rootfs_data starts
even earlier and modifies the checked region. The check will then fail and
the backup image (when available) will be booted.

Just setting it to the same number of skipped blocks as other 64K models
avoids this problem.

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-09-10 10:01:58 +02:00
Sven Eckelmann 0b20490207 ipq40xx: add support for OpenMesh A62
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
  - QCA9888 hw2.0 (PCI)
  - requires special BDF in QCA9888/hw2.0/board-2.bin
    bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
  - triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
  - phy@mdio3:
    + Label: Ethernet 1
    + gmac0 (ethaddr) in original firmware
    + 802.3at POE+
  - phy@mdio4:
    + Label: Ethernet 2
    + gmac1 (eth1addr) in original firmware
    + 18-24V passive POE (mode B)
* powered only via POE

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

The initramfs image can be started using

  setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
  tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
  set fdt_high 0x85000000
  bootm 0x84000000

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-04-23 22:07:22 +02:00
Sven Eckelmann b02fa3336b om-fwupgradecfg-gen.sh: add support for the A42
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2018-01-13 07:58:49 +01:00
Lorenzo Santina fd84ecda7d treewide: fix shellscript syntax errors/typos
Fix multiple syntax errors in shelscripts (of packages only)
These errors were causing many conditions to not working properly

Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[increase PKG_RELEASE, drop command substitution from directip.sh]
Signed-off-by: Mathias Kresin <dev@kresin.em>
2017-09-13 08:07:54 +02:00
Stijn Tintel c2a11bc8e4 scripts: make all scripts executable
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-07-14 04:09:16 +02:00
Sven Eckelmann 8cc4d1e27b scripts/om-fwupgradecfg-gen.sh: add support for the A60
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Felix Fietkau 84bd74057f build: use mkhash to replace various quirky md5sum/openssl calls
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-05 11:09:12 +01:00
John Crispin a910a2cdc7 scripts/om-fwupgradecfg-gen.sh: add support for the OM5P-AC
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49143
2016-04-09 10:25:54 +00:00
John Crispin 8583cbe26a scripts/om-fwupgradecfg-gen.sh: Generate sha256sum for uboot verification
Future Open Mesh u-boot versions are changing the check of the image files
(vmlinux, rootfs) from md5 to sha256. Having both in them should be enough
to ensure backward and forward compatibility.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49140
2016-04-09 10:25:42 +00:00
John Crispin 3d5cdf7094 scripts/om-fwupgradecfg-gen.sh: add support for the MR1750
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46928
2015-09-14 20:11:18 +00:00
John Crispin 5798dfb846 scripts/om-fwupgradecfg-gen.sh: Fix u-boot image md5sum check
The u-boot on Open Mesh devices checks the whole transfered image against a
md5sum. This is stored inside the option filemd5sum inside the
fwupgrade.cfg. The bootloader will not check it when this setting is
missing and could therefore write invalid images to the flash.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46925
2015-09-14 20:10:10 +00:00
John Crispin 9b1bc2d671 scripts/om-fwupgradecfg-gen.sh: add support for the MR900
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 43260
2014-11-14 16:54:23 +00:00
John Crispin 4e03bdd63c scripts/om-fwupgradecfg-gen.sh: add support for the OM5P
Signed-off-by: Marek Lindner <marek@open-mesh.com>
[sven@open-mesh.com: Rebased]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 41771
2014-07-20 17:30:48 +00:00
Gabor Juhos d325e622d2 scripts/om-fwupgradecfg-gen.sh: add support for the MR600
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34233
2012-11-18 09:32:36 +00:00
Gabor Juhos 7da001d068 scripts: rename om2p-fwupgradecfg-gen.sh to more generic om-fwupgradecfg-gen.sh
It will be used for non OM2P boards as well.

Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34200
2012-11-14 14:18:33 +00:00