kmod-drm-imx-hdmi depends on kmod-drm-display-helper since 6.1. Include
that in OpenWrt's recipes.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
This adds support for the Fritzbox 7490 device. It contains two
SoCs, one Lantiq without WiFi and one QCA9558 with 2.4GHz
and 5 GHz WiFi. Only the Lantiq has access to the flash memory,
the Atheros runs fully from RAM and is booted by using a remoteproc
kernel module and is not supported with this commit.
The devices were manufactured with varying NAND chips which
requires Micron and non-Micron versions of the images.
Specifications:
- SoC: Lantiq 500 MHz
- RAM: 256 MB
- Storage: 512 MB NAND, 1MB FLASH
- Wireless, separate SOC QCA9558 with 128MB RAM (not supported yet):
· Qualcomm-QCA9558 w/ 3×3 MIMO for 2.4GHz 802.11b/g/n
· Qualcomm-QCA9880 w/ 3×3 MIMO for 5GHz 802.11a/ac
· AG71xx ethernet
- Ethernet: Built-in AR 803x, 7 port 4 phy switch,
4x 1000/100/10 port, Port 5 is fixed and connected to the WASP SOC
- Renesas µPD720202 USB3 PCIe, requires firmware binary on the device
- VDSL2 modem
Unsupported:
- DECT and ISDN telephony
Installation:
Check which NAND the device has by using the following procedure with
stock firmware:
Go to to http://<fritzbox_ip>/support.lua, download the support data
file and search for string "NAND device" to get the manufacturer kernel
output.
Use Micron image if Micron is displayed otherwise the non-Micron image.
Use the eva_ramboot.py script to boot the initramfs image. Follow the
procedure to interrupt booting by ftp into 192.168.178.1 within
5 seconds after poweron.
Then transfer the sysupgrade image to the device and run sysupgrade to
flash it to the NAND.
For making USB work, an renesas xhci firmware file (e.g. v2026) is
needed and it should be copied to /lib/firmware/ (file name
renesas_usb_fw.mem).
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Since we have the 'GPIO support' menu, it is strange to look up
gpio related modules in 'Other modules' menu. So move these
modules and put them in the gpio menu.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Disable compiling qca8081 PHY driver in favor of upstream to better
support it and add better control of attached LEDs.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Completely disable dump_survey code on ARCH_BCM2835 to fix defined but not
used warning.
512b762ddb?w=1#commitcomment-137899352
Fixes: 512b762ddb ("mac80211: brcm: disable dump_survey on Raspberry Pi")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Enabling this causes slow iwinfo calls on Raspberry Pi and LuCI slows down
when wireless is enabled.
Fixes: https://github.com/openwrt/openwrt/issues/14013
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This patch has been reverted in the Raspberry Pi linux repository.
Also refresh the rest of the patches.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Backport merged upstream patch that adds support for firmware loader
from NVMEM or attached filesystem for Aquantia PHYs.
Refresh all kernel patches affected by this change.
Also update the path for aquantia .ko that got moved to dedicated
directory upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
[rmilecki: port to 5.15]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
raspberrypi/firmware is about 40G, so getting the full history log isn't an
option.
There have been multiple improvements and also support for the RPi 5 has been
added.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add kernel module for lp5562 LED driver.
The kmod-leds-lp5562 depends on kmod-leds-lp55xx-common.
Signed-off-by: CheWei Chien <chewei.chien@wnc.com.tw>
This reverts commit b7f9742da8.
There are several reports of regressions with this commit. Will be added
back once I've figured out and fixed the cause
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When hitting a timing window where ubus configuration calls are hitting hostapd
and wpa_supplicant simultaneously, they can deadlock waiting for each other.
Fix this by using a lock around the ubus calls.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Frequent crashes have been observed on MT7916 based platforms. While the
root of these crashes are currently unknown, they happen when decoding
rate information of connected STAs in AP mode. The rate-information is
associated with a band which is not available on the PHY.
Check for this condition in order to avoid crashing the whole system.
This patch should be removed once the roout cause has been found and
fixed.
Link: https://github.com/freifunk-gluon/gluon/issues/2980
Signed-off-by: David Bauer <mail@david-bauer.net>
Add modules.builtin.modinfo to the kernel package, to support presence
testing using module aliases and printing module details with 'modinfo'.
With related kmodloader changes this adds ~2 KB to compressed image sizes.
root@OpenWrt:/# modinfo unix
name: unix
filename: (builtin)
alias: net-pf-1
license: GPL
root@OpenWrt:/# modprobe net-pf-1 && echo SUCCESS || echo FAIL
SUCCESS
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Add modules.builtin to the kernel package for improved handling of loadable
and builtin modules. As with other distros, this allows 'modprobe <module>'
to consistently return success for both loaded/built-in modules, a useful
feature for presence-testing.
Given OpenWrt's few built-in modules, this change and related kmodloader
support add ~1 KB to the compressed image size.
Using sch_fq_codel (builtin) and sch_cake (loadable) for example:
root@OpenWrt:/# modprobe sch_fq_codel && echo SUCCESS || echo FAIL
SUCCESS
root@OpenWrt:/# modprobe sch_cake && echo SUCCESS || echo FAIL
SUCCESS
root@OpenWrt:/# rmmod sch_fq_codel
module is builtin
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
fast-xmit must only be enabled after the sta has been uploaded to the driver,
otherwise it could end up passing the not-yet-uploaded sta via drv_tx calls
to the driver, leading to potential crashes because of uninitialized drv_priv
data.
Add a missing sta->uploaded check and re-check fast xmit after inserting a sta.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes WARN_ONs when using AP_VLANs after station removal. The flush
call passed AP_VLAN vif to driver, but because these vifs are virtual and
not registered with drivers, we need to translate to the correct AP vif
first.
Fixes: openwrt#12420
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
Detach of-mdio dependency from stmmac-core kmod to fix support for
x86_64 target. This target doesn't use OpenFirmware infrastructure and
stmmac-core for the dwmac-intel driver doesn't depends on it.
Add kmod-of-mdio to any other user of stmmac-core as it's not inherit
from stmmac-core anymore.
Fixes: #14209
Fixes: 4b4c940fbc ("x86: Add kmod-dwmac-intel")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move pcs-xpcs kmod from armsr modules.mk to generic modules package.
Also add additional dependency to x86_64 as stmmac-core it's now used
by x86_64 target and depends on this package.
Fixes: 4b4c940fbc ("x86: Add kmod-dwmac-intel")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Might be a typo in drv->txtstamp function:
+ phy_rxtstamp(ndev->phydev, skb, 0);
to
+ phy_txtstamp(ndev->phydev, skb, 0);
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Remove upstreamed patches:
* replace usage of the deprecated "pci-dma-compat.h" API (6c03b27)
* remove uaccess and get_fs calls from PCIe for Kenel >= 5.18 (1d0d08c)
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Backport merged upstream patch that adds support for firmware loader
from NVMEM or attached filesystem for Aquantia PHYs.
Refresh all kernel patches affected by this change.
Also update the path for aquantia .ko that got moved to dedicated
directory upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
ISISC is the QCA codename for their Atheros switch family including
AR237, QCA8337 etc.
Since we have qca8k support in OpenWrt, there is no need to have SSDK
support for these switches, and boards that also have external switches
can just use qca8k.
Disable QCA803x PHY support as well, since all of those are supportable
via at803x driver.
Signed-off-by: Robert Marko <robimarko@gmail.com>
PTP and swconfig support in SSDK require kernel modifications we dont need
nor we want to support for now, so move the PTP and swconfig disablement
into general build options as they are not ipq807x specific.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Recent SSDK versions started also parsing the "SoC" variable to identify
the SoC along with the "CHIP_TYPE".
We are not passing "SoC" currently and this leads to components we dont
need like MHT (New 2.5G quad port switch) being compiled and then unused,
so lets just pass the "SoC" as well.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RTW88 PCI/USB driver uses the same firmware,
so add firmware dependencies.
Also CI report that:
Package kmod-rtw88-usb is missing dependencies for the following libraries:
usbcore.ko
This commit fixes it.
Fixes: 3538a19 ("mac80211: split rtw88 configuration for each supported chip")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Commit 947b44d ("ipq807x: fix wrong define for LAN and WAN ess mask")
started fixing wrong switch_lan_bmp that defined lan there weren't
actually present. This displayed a fragility in the malibu phy init code
in qca-ssdk.
Add patch to fix this. Also update each DTS with the new required
property if needed.
The new binding malibu_phy_start_addr is required with devices that
place the malibu first PHY referring port1 on a different PHY addres
than 0. The most common configuration is 0 but some device (for example
Qnap 301W) place the malibu PHY at an offset to address 16.
Refer to ipq8074-ess dtsi for extensive description on how to derive
this value.
Quoting the patch detailed description:
The usage of first_phy_addr is EXTREMELY FRAGILE and results
in dangerous results if the OEM (or anyone that by chance try to
implement things in a logical manner) deviates from the default values
from the "magical template".
To be in more details. With QSDK 12.4, some tweaks were done to improve
autoneg and now on every call of port status, the phydev is tried to
add. This resulted in the call and log spam of an error with ports that
are actually not present on the system with qsdk reporting phydev is
NULL. This itself is not an error and printing the error is correct.
What is actually an error from ages is setting generic bitmap reporting
presence of port that are actually not present. This is very common on
OEM where the switch_lan_bmp is always a variant of 0x1e (that on bitmap
results in PORT1 PORT2 PORT3 PORT4 present) or 0x3e (PORT1 PORT2 PORT3
PORT4 PORT5). Reality is that many device are used as AP with one LAN
port or one WAN port. (or even exotic configuration with PORT1 not
present and PORT2 PORT3 PORT4 present (Xiaomi 3600)
With this finding one can say... ok nice, then lets update the DT and
set the correct bitmap...
Again world is a bad place and reality is that this cause wonderful
regression in some case of by extreme luck the first ever connected
port working and the rest of the switch dead.
The problem has been bisected to all the device that doesn't have the
PORT1 declared in any of the bitmap.
With this prefaction in mind, on to the REAL problem.
malibu_phy_hw_init FOR SOME REASON, set a global variable first_phy_addr
to the first detected PHY addr that coincidentally is always PORT1.
PORT1 addr is 0x0. The entire code in malibu_phy use this variable to
derive the phy addrs in some function.
Declaring a bitmap where the PORT1 is missing (or worse PORT4 the only
one connected) result in first_phy_addr set to 1 or whatever phy addr is
detected first setting wrong value all over the init stage.
To fix this, introduce a new binding malibu_first_phy_addr to manually
declare the first phy that the malibu PHY driver should use and permit
to detach it from port bmp detection. The legacy detection is kept for
compatibility reason.
Fixes: #13945
Fixes: 947b44d9ae ("ipq807x: fix wrong define for LAN and WAN ess mask")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Tested-by: Robert Marko <robimarko@gmail.com> # Qnap 301W
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 8cce00bc9d.
The confusion was real and this change cause regression on other
advanced devices that makes actual use of the first_phy_addr value.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some local patches have been sent to upstream and they are slightly
different from the upstream version. So it's better to replace them
to avoid conflicts with the new mac80211 backport driver. The
different parts have been merged into patch 996.
This commit also includes some additional fixes:
* Fix watchdog function.
* Improve MT7620 register initialization.
* Introduce DMA busy watchdog for rt2800.
P.S.
Sometimes rt2800 series chips may fall into a DMA busy state. The
tx queues become very slow and the client cannot connect to the AP.
Usually, We can see a lot of hostapd warnings at this point:
'hostapd: IEEE 802.11: did not acknowledge authentication response'
The DMA busy watchdog can help the driver automatically recover
from this abnormal state. By the way, setting higer 'cell_density'
and disabling 'disassoc_low_ack' can significantly reduce the
probability of the DMA busy.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Kernel 6.1 has introduced support for RTW8822BU network adapter, which
is an USB variant of the rtw8822b 802.11ac chipset family.
Build and install the corresponding module in the rtw88 package
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Current rtw88 build configuration builds modules for all chips supported by
rtw88 driver family. This brings the following issues:
- adding a chip with a different bus is not convenient (all chips currently
depends on PCI)
- some features requirements are not relevant for all chips in family (eg
802.11AC is enforced but RTW88-8723DE is only a 802.11b/g/n chip)
Remove those constraints/issues by adding one module build option per
supported chip, and add intermediate options to properly cascade
dependencies.
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
ath9k-htc USB-based adapters also support 5/10MHz channel bandwidth.
Move the code handling the features in debugfs to common-debug.c,
and create proper registration functions to use in debug.c and
htc_drv_debug.c, leaving only debugfs registration there.
While at that, refresh one patch that would conflict otherwise.
Tested on TP-Link Archer C7v2 (ath79) and TP-Link WN722Nv1 (AR9287)
and WN822Nv2 (AR7010+AR9287).
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
ath9k-htc USB-based adapterssupport 5/10MHz channel bandwidth, the
same as standard ath9k ones.
Move the code handling the features in debugfs to common-debug.c,
and create proper registration functions to use in debug.c and
htc_drv_debug.c, leaving only debugfs registration there.
While at that, refresh one patch that would conflict otherwise.
Tested on TP-Link Archer C7v2 (ath79) and TP-Link WN722Nv1 (AR9287)
and WN822Nv2 (AR7010+AR9287).
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
In-kernel driver for MCS7715 USB-serial bridge has a bool option,
enabling support for parallel port on that chip - which is tied to the
same kernel module. Enable it and select kmod-ppdev, as the image size
increase is minimal and the package isn't bundled in the images by
default.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Adjust our local ath10k-ct patches to the change
from the -ct 6.2 version to 6.4.
This restores e.g. the LED functionality.
Fixes: 7d3651f1b9 ("ath10k-ct: switch to 6.4")
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Commit 947b44d9ae ("ipq807x: fix wrong define for LAN and WAN ess mask")
started fixing wrong switch_lan_bmp that defined lan there weren't
actually present. This displayed a fragility in the malibu phy init code
in qca-ssdk.
Add patch to fix this.
Quoting the patch detailed description:
I'm very confused by this and to me it's not clear the real usage of
this logic.
From what I can see the usage of this is EXTREMELY FRAGILE and results
in dangerous results if the OEM (or anyone that by chance try to
implement things in a logical manner) deviates from the default values
from the "magical template".
To be in more details. With QSDK 12.4, some tweaks were done to improve
autoneg and now on every call of port status, the phydev is tried to
add. This resulted in the call and log spam of an error with ports that
are actually not present on the system with qsdk reporting phydev is
NULL. This itself is not an error and printing the error is correct.
What is actually an error from ages is setting generic bitmap reporting
presence of port that are actually not present. This is very common on
OEM where the switch_lan_bmp is always a variant of 0x1e (that on bitmap
results in PORT1 PORT2 PORT3 PORT4 present) or 0x3e (PORT1 PORT2 PORT3
PORT4 PORT5). Reality is that many device are used as AP with one LAN
port or one WAN port. (or even exotic configuration with PORT1 not
present and PORT2 PORT3 PORT4 present (Xiaomi 3600)
With this finding one can say... ok nice, then lets update the DT and
set the correct bitmap...
Again world is a bad place and reality is that this cause wonderful
regression in some case of by extreme luck the first ever connected
port working and the rest of the switch dead.
The problem has been bisected to all the device that doesn't have the
PORT1 declared in any of the bitmap.
With this perfection in mind, on to the REAL problem.
malibu_phy_hw_init FOR SOME REASON, set a global variable first_phy_addr
to the first detected PHY addr that coincidentally is always PORT1.
PORT1 addr is 0x0. The entire code in malibu_phy use this variable to
derive the phy addrs in some function.
Declaring a bitmap where the PORT1 is missing (or worse PORT4 the only
one connected) result in first_phy_addr set to 1 or whatever phy addr is
detected first setting wrong value all over the init stage.
To fix this, just drop this variable and hardcode everything to assume
the first phy adrr is ALWAYS 0 and remove calculation and use define for
special case.
With the following change normal switch traffic is restored and ports
function is recovered.
Fixes: #13945
Fixes: 947b44d9ae ("ipq807x: fix wrong define for LAN and WAN ess mask")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
noscan option was changed to hostapd_noscan but the entry in
wpa_supplicant was never updated resulting in the noscan option actually
never set.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Update SSDK version to 12.4, this fixes weird SFP port link up/downs
while there is no SFP module plugged in.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This fixes the download of the kernel 5.15 for the bpf-headers when
kernel 6.1 is build for the target.
Even if kernel 6.1 was selected for the target we still use kernel 5.15
for the bpf-headers. The download script tried to download the 5.15
kernel from the 6.x directory on kernel,org and this failed. Define
PKG_SOURCE_URL based on PKG_PATCHVER and not KERNEL_BASE like done in
kernel.mk.
Without this change it tries to download the kernel from this URL:
ttps://cdn.kernel.org/pub/linux/kernel/v6.x/linux-5.15.129.tar.xz
Fixes: #13190Fixes: #13671Fixes: #13814
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ath10k-ct based on kernel 6.4 doesn't have a fix present in previous
kernel. Add patch that port the compilation error fix from previous
kernel in the new 6.4 kernel.
Fixes: 7d3651f1b9 ("ath10k-ct: switch to 6.4")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Switch to the latest version so we match as close as possible to
our own mac80211 version.
Run-time tested on hundreds of devices in the field for months now:
- qca988x (wave 1)
- qca4019 (wave 2)
Tested-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Add a struct_group to around all members in struct ath_cycle_counters.
It can help the compiler detect the intended bounds of the memcpy() and
memset().
This patch fixes the following build warning:
In function 'fortify_memset_chk',
inlined from 'ath9k_ps_wakeup' at /home/db/openwrt/build_dir/target-mips_24kc_musl/linux-ath79_generic/backports-6.1.24/drivers/net/wireless/ath/ath9k/main.c:140:3:
./include/linux/fortify-string.h:314:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
314 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Currently the zram default compressor choice is displayed whether or not
zram is activated. Since the default choice is lzo-rle, this adds a
false dependency on kmod-lib-lzo.
With this patch, the choice options appear only when activating zram.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Fix the building issue setting CC to KERNEL_CC in kernel.mk. The
kernel backports by default uses CC to compile kconf. A new patch is
added to mac80211 to compile kconf with host gcc.
Signed-off-by: Zeyu Dong <dzy201415@gmail.com>
[ refresh patches ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
CONFIG_USB_AUDIO is a "USB Audio Gadget" driver, not a usb device driver
CONFIG_USB_AUDIO is "USB Audio support" before linux 2.6
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
Expose the temperature sensors as hwmon, it improves the overall
user experience since on tiny boards the nvme can become a substantial
source of heat.
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
Reviewed-by: Robert Marko <robimarko@gmail.com>
The IXP4xx crypto module must be loaded after the rootfs is
up as it depends on loading some NPE microcode from the file
system.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make use of new toolchain define. TOOLCHAIN_DIR should be used only for
toolchain related packages and for everything else TOOLCHAIN_ROOT_DIR
and other define should be used instead.
Switch to new entry where possible.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some packages won't ever have something to patch as they normally
install files or are meta-packages.
For these special packages, disable QUILT refresh.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
To support the IXP42x platforms we need a kernel module
for the Epson R7301 RTC so we can load it as an optional
module.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Robert Marko <robimarko@gmail.com>
To support the IXP42x platforms we need a kernel module
for the X1205 RTC so we can load it as an optional module.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Robert Marko <robimarko@gmail.com>
The lib-chacha20 library is missing build rules for big endian
ARM, and since IXP4xx is big endian ARM we need those rules to
build for IXP4xx.
Suggested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Improve EEPROME load patches. Reorganize and rework them.
The current patch are bugged and with the case of MTD loading, leaks and
never free the EEPROM read values.
Also add support for loading EEPROM using NVMEM cells.
As a cleanup, change the binding to swap EEPROM read from mtd to
ralink,eeprom-swap and generilize it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Synchronize the ath11k backports with the current ath-next tree.
All of the changes are various bugfixes, there is no new major feature.
Notable bugfixes are:
* WCN6855 board name fixes
* One MSI vector booting is working again
This is rather important for most of the older platforms.
* DFS CAC state in virtual interfaces was fixed
* TX power during CAC reporting
Signed-off-by: Robert Marko <robimarko@gmail.com>
DFS CAC time export is required for backport of a ath11k fix so lets
backport the required cfg80211 upstream commit as well.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The PKG_MIRROR_HASH is wrong, fix it.
Found and fixed using this command:
make package download check FIXUP=1
Fixes: c123e4f053 ("rtl8812au-ct: bump to fix kernel 6.1 compile")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The mt76 driver usually reads the eeprom on the mtd partition at dts.
For emmc device we need to use caldata_extract script to read the
eeprom. However, the default eeprom file breaks the caldata script
execution, so remove it.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Package and add dependencies to drm-amdgpu and drm-radeon for 6.1
* package acpi-video, drm-display-helper and drm-buddy
* add acpi-video, drm-display-helper and drm-buddy as dependencies for
drm-amdgpu
* add acpi-video and drm-display-helper as dependencies for drm-radeon
Signed-off-by: Pascal Coudurier <coudu@gmx.com>
Synchronize the ath11k backports with the current ath-next tree.
All of the changes are various bugfixes, there is no new major feature.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit ed3725e15a154ebebf44e0c34806c57525483f92
("wifi: ath11k: Fix qmi_msg_handler data structure initialization")
has been present upstream since 6.1.2 but it seems Quilt refreshed it
wrongly so it appeared like a completely different patch.
Commit 7c15430822e71e90203d87e6d0cfe83fa058b0dc
("wifi: ath11k: allow system suspend to survive ath11k")
has been present upstream since 6.1.16 but somehow quilt still happily
applied it.
So, drop both of them.
Signed-off-by: Robert Marko <robimarko@gmail.com>
General support for 9P is desirable on platforms without virtualization.
This decouples the 9P general networking support for use on more platforms.
Signed-off-by: Daniel Maslowski <info@orangecms.org>
MAC address and interface name assigned by mac80211.sh depend on the order in
which interfaces are brought up. This order changes when interfaces get added
or removed, which can cause unnecessary reload churn.
One part of the fix it making MAC address allocation more dynamic in both
wpa_supplicant and hostapd, by ignoring the provided MAC address using
the next available one, whenever the config does not explicitly specify one.
The other part is making use of support for renaming netdevs at runtime and
preserving the MAC address for renamed netdevs.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When a device has more than one reserved mac address, they can be used for
virtual interfaces without the local bit in the first byte
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Mediatek EIP93 Crypto engine is a crypto accelerator which
is available in the Mediatek MT7621 SoC.
Signed-off-by: Aviana Cruz <gwencroft@proton.me>
Co-authored-by: Richard van Schagen <vschagen@icloud.com>
Co-authored-by: Chukun Pan <amadeus@jmu.edu.cn>
When switching from a STA-only configuration to AP+STA on the same phy, the
STA was previously restarted in order to notify hostapd of the new frequency,
which might not match the AP configuration.
Fix the STA restart by querying the operating frequency from within hostapd
when bringing up the AP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It seems that this was not functioning properly and was likely completely unused.
Keeping this out of tree also introduced some annoying churn when updating, because
of the iw nl80211.h sync patch.
If this is needed, it will be reintroduced when/if it is added upstream
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Arm platforms with the right hardware blocks (such as
GICv3.0+ interrupt controller and SMMU/IOMMU) are
able to use vfio-pci to pass through PCI devices
to a VM.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The vfio module only exposes the enable_unsafe_noiommu_mode parameter
if CONFIG_VFIO_NOIOMMU is enabled. When it isn't, the module
will complain about an unknown parameter:
vfio: unknown parameter 'enable_unsafe_noiommu_mode' ignored
As CONFIG_VFIO_NOIOMMU is disabled by the module package,
we can remove the module loading parameter.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
vhost-net is used to accelerate traffic to virtualisation
guests that use the virtio-net network card in QEMU.
Generally it is invoked by specifying "vhost=on" to a
QEMU -netdev device:
qemu-system-aarch64 -nographic -M virt -cpu host \
--enable-kvm -bios u-boot.bin -smp 1 -m 2048 \
-drive file=openwrt-armsr-armv8.img,format=raw,index=0,media=disk \
-device "virtio-net,netdev=landev,disable-legacy=off,disable-modern=off" \
-netdev "tap,id=landev,helper=/usr/lib/qemu-bridge-helper --br=br-lan,vhost=on"
Signed-off-by: Mathew McBride <matt@traverse.com.au>
During the channel scanning process, the driver will continuously
switch channels. It seems that the full RF calibration step in
rt2800_config_channel() caused the channel scanning function to
timeout. To fix it, move the RF calibration to rt2800_enable_radio()
so that it is only executed once. This commit also includes some
coding format adjustments to follow the Linux recommended style.
Fixes: 2824fa6963 ("mac80211: rework MT7620 PA/LNA RF calibration")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The vendor U-Boot implementaion on Telenor branded ZyXEL EX5700
devices does not store its environment on flash. It is instead
kept in a memory region. This is persistent over reboots, but
not over power cycling.
The dual partition failsafe system used by the vendor U-Boot
requires the OS to modify a variable in this memory environment.
This driver allows the ordinary uboot-envtools to access a
memory region like it was a partition on NOR flash.
The specific vendor U-Boot adds a "no-map" /reserved-memory
section and a top level /ubootenv node pointing to the memory
environment. The driver uses this device specific fact to
locate the region. The matching and probing code will likely
have to be adjusted for any other devices to be supported.
Example partial device tree:
/ {
..
ubootenv {
memory-region = <&uenv>;
compatible = "ubootenv";
};
..
reserved-memory {
..
uenv: ubootenv@7ffe8000 {
no-map;
reg = <0 0x7ffe8000 0 0x4000>;
};
Signed-off-by: Bjørn Mork <bjorn@mork.no>
9b2b203 fix usb_recv_tasklet -Wcast-function-type
a027da5 fix kernel 6.1 80211 link_id
7a9c802 fix build for kernel 6.1 prandom
3a3eb24 fix build for kernel 5.17 PDE_DATA
fe2afbd fix build for kernel 5.17 const netdev->dev_addr
7275bae fix build for 5.17 kernel complete_and_exit
c9c2aa7 Update usb_intf.c
revert the upstream 6.1 link_id (depend on kernel version) changes and
force 6.1 link_id
The downstream patch casting const off the direct dev_addr writes
triggers the runtime check from
Linux d07b26f5bbea ("dev_addr: add a modification check")
Fixes: #13261
Fixes: a07566ead8 ("rtl8812au-ct: fix even more compilation error with kernel 6.1")
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Tear down all interfaces if the antenna settings change, so that the
capabilities can be recalculated properly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Package kernel module for Marvell 10G Ethernet PHYs found also in many
10G/1G/100M/10M RJ-45 SFP+ modules.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This implements vastly improved dynamic configuration reload support.
It can handle configuration changes on individual wifi interfaces, as well
as adding/removing interfaces.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support for the SKBPRIO queuing discipline. This is subtly
different than prio as it also drops packets from the lower priority
flows.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Fix more compilation error with kernel 6.1 and make it possible to
compile.
Multiple fix are done due to kernel bump:
- PDE_DATA (now deprecated) to pde_data
- dev_addr now const and require some cast
- prandom_u32 (now deprecated) to get_random_u32
Also other minor fix for always true condition and tasklet type cast not
compatible.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patch makes some improvements to the MT7620 RF calibration.
1. Move MT7620 PA/LNA calibration code to dedicated functions.
2. Restore RF and BBP registers before R-Calibration.
3. Do Rx DCOC calibration again before RXIQ calibration.
4. Use SoC specific AGC initial LNA value.
5. Correct MAC_RX_EN mask in rt2800_r_calibration()[1].
[1] This change may fix the "BBP/RF register access failed" error:
ieee80211 phy0: rt2800_wait_bbp_rf_ready: Error - BBP/RF register access failed, aborting
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
53edfc7aaa34 wifi: mt76: mt7603: fix beacon interval after disabling a single vif
7ef4dd12d982 wifi: mt76: mt7603: fix tx filter/flush function
152608a40aa7 wifi: mt76: mt7615: do not advertise 5 GHz on first phy of MT7615D (DBDC)
cacac3902a63 wifi: mt76: split get_of_eeprom in subfunction
cd3dfe392769 wifi: mt76: add support for providing eeprom in nvmem cells
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Kernel 6.1 have renamed complete_and_exit to kthread_complete_and_exit.
This was just a rename and nothing is changed implementation wise.
Fix compilation error by using the new symbol name.
Fix compilation error:
In file included from /builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/include/osdep_service.h:41,
from /builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/include/drv_types.h:32,
from /builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/core/rtw_cmd.c:22:
/builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/core/rtw_cmd.c: In function 'rtw_cmd_thread':
/builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/include/osdep_service_linux.h:166:23: error: implicit declaration of function 'complete_and_exit' [-Werror=implicit-function-declaration]
166 | #define thread_exit() complete_and_exit(NULL, 0)
| ^~~~~~~~~~~~~~~~~
/builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/core/rtw_cmd.c:706:9: note: in expansion of macro 'thread_exit'
706 | thread_exit();
| ^~~~~~~~~~~
/builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/core/rtw_cmd.c:708:1: error: control reaches end of non-void function [-Werror=return-type]
708 | }
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patch adds basic TX power control for the MT7620 and limits its
maximum TX power. This can avoid the link speed decrease caused by
chip overheating.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The return value of the .remove function pointer has changed from
int to void with Linux 5.18. Use a precompiler macro to allow building
the leds-ws2812b module with both, Linux 5.15 and Linux 6.1.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds support for the i.MX Pixel Pipeline IP block
which is available on some imx6 flavours [1]
This allows to use hardware offloading for operations like:
- Colour conversion
- Scaling
- Rotation
[1] https://en.wikipedia.org/wiki/I.MX#i.MX_6_series
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
This adds support for the Video Processing Unit IP block
which is present in certain i.MX SOC's.
The vpu used in imx6 is the coda960 which supports:
- h264 enc
- h264 dec
- jpeg enc
- jpeg dec
Please note that the required firmware needs to be added
by yourself as it's not available currently in linux-firmware upstream.
The firmware package can be found on the internet
and it will decompress itself exposing all binaries
after accepting the EULA.
The binaries should be placed at exactly these paths:
- /lib/firmware/vpu_fw_imx6d.bin
- /lib/firmware/vpu_fw_imx6q.bin
Following output will be printed at boottime if all is well:
[ 9.769638] coda 2040000.vpu: Firmware code revision: 46076
[ 9.775277] coda 2040000.vpu: Initialized CODA960.
[ 9.780082] coda 2040000.vpu: Firmware version: 3.1.1
[ 9.785312] coda 2040000.vpu: coda-jpeg-encoder registered as video0
[ 9.791859] coda 2040000.vpu: coda-jpeg-decoder registered as video1
[ 9.798375] coda 2040000.vpu: coda-video-encoder registered as video2
[ 9.805013] coda 2040000.vpu: coda-video-decoder registered as video3
gstreamer will automatically detect and use all encoders/decoders.
Please note that a FILES catch-all is required for the videobuf-dma objects
as some modules enabling this could require (and thus generating) only 1 of them.
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
This adds support for videobuf2-dma driver.
This module contains following flavors:
- Contiguous
- Scatter/Gather
Drivers using this can enable 1 of the, or both, depending on their needs.
Due to this, a FILES catch-all is required for the videobuf-dma objects
as depending on requirements, only 1 of them could get generated.
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
This allows addition of devices which use these kernel
modules.
This also adds a package for handling dma within video2buf.
These are only build when selected by a caller
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
All patches automatically rebased.
Acknowledgment to @john-tho for the changes to fs.mk to accommodate new paths
introduced in 29429a1f58
Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B
Signed-off-by: John Audia <therealgraysky@proton.me>
This patch will only force mac80211 loss detection upon ath10k by
masking the driver-specific loss-detection bit.
Ref: commit ed816f6ba8 ("mac80211: always use mac80211 loss detection")
Signed-off-by: David Bauer <mail@david-bauer.net>
In the recent NSS-DP update FDB roaming fix we had was removed as in
testing no issue were reported, but after it was merged the old duplicate
MAC issue reappeared so lets port the previous FDB fix to work with newer
NSS-DP.
Fixes: 4ee444b5da ("kernel: qca-nss-dp: update to 12.4.5.r1")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Qualcomm has finally started the preparatory work in order to support
kernel 6.1, so lets make use of that and update NSS-DP 12.4.5.r1 which
allows us to drop almost some of the patches.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Qualcomm has finally started the preparatory work in order to support
kernel 6.1, so lets make use of that and update SSDK 12.4.5.r1 which
allows us to drop almost all of the patches.
Lets also install the forgotten SSDK netlink header.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix a typo where the wrong KCONFIG was used and fix selecting the
correct kernel config option to use these packages.
Fixes: 4f443c885d ("netfilter: separate packages for kmod-ipt-socket and kmod-ipt-tproxy")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
ath10k does not report excessive loss in case of broken block-ack
sessions. The loss is communicated to the host-os, but ath10k does not
trigger a low-ack events by itself.
The mac80211 framework for loss detection however detects this
circumstance well in case of ath10k. So use it regardless of ath10k's
own loss detection mechanism.
Signed-off-by: David Bauer <mail@david-bauer.net>
Now that qualcommax exists as a target and dependencies have been updated
let move ipq807x support to subtarget of qualcommax.
This is mostly copy/paste with the exception of having to update SSDK and
NSS-DP to use CONFIG_TARGET_SUBTARGET.
This is a preparation for later addition of IPQ60xx and IPQ50xx support.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, ipq807x only covers Qualcomm IPQ807x SoC-s.
However, Qualcomm also has IPQ60xx and IPQ50xx SoC-s under the AX WiSoC-s
and they share a lot of stuff with IPQ807x, especially IPQ60xx so to avoid
duplicating kernel patches and everything lets make a common target with
per SoC subtargets.
Start doing that by renaming ipq807x to qualcommax so that dependencies
on ipq807x target can be updated.
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is no need for SSDK to support 5.15 anymore since the only user and
possible future ones are on 6.1.
Signed-off-by: Robert Marko <robimarko@gmail.com>
One is never to write to dev->addr directly. In 6.1 it will be a const and
with the newly enabled WERROR, we get a failing grade.
Lets fix this ahead of time.
Ref: adeef3e321
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Currently kernel crashes when of_phy_connect has issues:
Unable to handle kernel access to user memory outside uaccess routines at virtual address 0000000000000308
...
pc : phy_attached_print+0x28/0x1b0
lr : phy_attached_info+0x14/0x20
...
Call trace:
phy_attached_print+0x28/0x1b0
phy_attached_info+0x14/0x20
nss_dp_adjust_link+0x544/0x6c4 [qca_nss_dp]
of_phy_connect returns either pointer or NULL, so can't be checked with
IS_ERR macro.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Synchronize the ath11k backports with the current ath-next tree.
This introduces support for MBSSID and EMA, adds factory test mode and
some new HTT stats.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport EMA beacon support from kernel 6.4.
It is required for MBSSID/EMA suport in ath11k that will follow.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Amazon ENA network devices are also used on the
AWS Arm (Graviton) instance types, so move it from
the x86-only module file to the top level netdevices.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The MDIO bus multiplexing framework is used by some drivers
such as dwmac-sun8i.
As this is a per-driver requirement, set it to be hidden in the menu.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
When using the Gemini, we apply patches that create a single
module that support both host and device mode these days.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(move module to gemini target, keep both 6.1+2-ish + 5.15 module
CONFIG and files around until 5.15 is dropped)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The smsc95xx driver got selftest support with kernel 5.18, add the new
dependency fixing the all kernel modules build on MIPS malta with kernel
6.1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_PHYLINK Kconfig option in the kernel selects CONFIG_LIBPHY.
Add this dependency to fix the all kernel modules build on MIPS malta
and armvirt with kernel 6.1.
With kernel 5.15 mod-phylink and kmod-sfp are empty packages because
no OpenWrt kmod is selecting a module which needs sfp or phylink
support.
Fixes: #12758
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add kernel 6.1 support to SSDK, it was just a case of adding the kernel
version identification and fixing up get_random_u32.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This was needed when we had 5.10 kernel as well, but now that all
targets are running 5.15 or 6.1 we can safely drop it.
Signed-off-by: Robert Marko <robimarko@gmail.com>
ath10k-ct now offers 6.2 and 6.4 versions, so lets update to use 6.2
so we can get rid of the API update patch as well as NVMEM as that is
already present in the newer driver.
Ben merged the debug compilation patch so we can remove that one as well.
Update patches to point to 6.2 version and refresh them.
Signed-off-by: Robert Marko <robimarko@gmail.com>
From commit dc0e6056de ("rxrpc: Fix missing dependency on NET_UDP_TUNNEL")
upstream, kmod-rxrpc uses functions enabled by CONFIG_NET_UDP_TUNNEL.
Add package dependencies on kmod-udptunnel4 and kmod-udptunnel6 to avoid
build errors like:
Package kmod-rxrpc is missing dependencies for the following libraries:
ip6_udp_tunnel.ko
udp_tunnel.ko
This change applies to both kernels 5.15 and 6.1.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
It's only used on devices in mt7621 and mt7622 subtargets, so no reason
to compile it for others.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
As of ed5c2f5fd10d ("i2c: Make remove callback return void") return
value of remove function is ignored.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Currently, SSDK is rather special in the sense that its not being built as
a proper out of tree module at all but rather like a userspace application
and that involves a lot of make magic which unfortunately broke with make
version 4.4 and newer.
Luckily QCA finally added a way to build SSDK as an out of tree module
and it uses the kernel buildsystem which makes it compile with make 4.4
as well.
So lets backport the support for it and switch to using it.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Kernel 6.1 now has fortify_memcpy_chk() and it is causing the following
warning while trying to compile backports:
CC [M] /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/net/wireless/util.o
In file included from ./include/linux/string.h:253,
from /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/backport-include/linux/string.h:3,
from ./include/linux/bitmap.h:11,
from ./include/linux/cpumask.h:12,
from ./include/linux/smp.h:13,
from ./arch/arm64/include/asm/arch_timer.h:18,
from ./arch/arm64/include/asm/timex.h:8,
from ./include/linux/timex.h:67,
from ./include/linux/time32.h:13,
from ./include/linux/time.h:60,
from /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/backport-include/linux/time.h:3,
from ./include/linux/skbuff.h:15,
from /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/backport-include/linux/skbuff.h:3,
from ./include/linux/if_ether.h:19,
from /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/backport-include/linux/if_ether.h:3,
from ./include/linux/etherdevice.h:20,
from /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/backport-include/linux/etherdevice.h:3,
from /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/net/wireless/util.c:12:
In function 'fortify_memcpy_chk',
inlined from 'ieee80211_strip_8023_mesh_hdr' at /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/net/wireless/util.c:590:3:
./include/linux/fortify-string.h:404:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
404 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
This issue was fixed in the final version of
("wifi: mac80211: fix receiving A-MSDU frames on mesh interfaces") that was
merged upstream but we have a older version that is using:
memcpy(&payload.eth.h_dest, mesh_addr, 2 * ETH_ALEN);
instead of:
memcpy(&payload.eth, mesh_addr, 2 * ETH_ALEN);
So, lets just backport the merged version of patch to fix the issue.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Adapt filesystem kmods for building under kernel 6.1:
* Depend on kernel not being 5.10 rather than only 5.15
* kmod-fs-9p depends on kmod-fs-netfs from 5.17 as they started using
netfs helpers
* Set new KConfig options to N
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update the WWAN kmods for compilation under kernel 6.1:
* Depend on kernel not being 5.10 rather than only 5.15
* Enable CONFIG_WWAN_DEBUGFS as its now optional from 5.17
* Add missing symbols for new WWAN drivers to generic config
Signed-off-by: Robert Marko <robimarko@gmail.com>
The x86_64 UML target wants to include SSSE3 optimized
crypto code which lives under /arch/x86/crypto.
However, these are not built and this causes an error.
| ERROR: module '[...]/arch/x86/crypto/sha512-ssse3.ko' is missing.
| make[3]: *** [modules/crypto.mk:990: [...]/kmod-crypto-sha512_5.15.112-1_x86_64.ipk] Error 1
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
That was a workaround for OpenWrt generation of config files. This patch
was used to postpone returning from probe function until loading
firmware and calling register_wiphy().
All of that is not needed anymore thanks to the ieee80211 hotplug.d
script introduced in the commit 5f8f8a3661 ("base-files, mac80211,
broadcom-wl: wifi detection and configuration"). That takes care of
generating /etc/config/wireless entries even if wireless device appears
late in the booting process.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
IGD is only useful when accelerating a VM guest that wants to direct
render to memory in the host's framebuffer, but since OpenWrt
typically runs on headless hardware, this serves no purpose.
Also build vfio with VFIO_NOIOMMU undefined (to get all of the code
enabled), but allow it to be enabled via boot-time modparams
settings (or at run-time via sysfs writes to
"/sys/module/vfio/parameters/enable_unsafe_noiommu_mode".
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Lech Perczak