ath79: add support for Netgear EX6400 and EX7300

This is sold as a dual-band 802.11ac range extender. It has a sliding
switch for Extender mode or Access Point mode, a WPS button, a recessed
Reset button, a hard-power button, and a multitude of LED's, some
multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is
Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may
connect at 115200 bps, 8 data bits, no parity, 1 stop bit.

Specification:
- System-On-Chip: QCA9558
- CPU/Speed: 720 MHz
- Flash-Chip: Winbond 25Q128FVSG
- Flash size: 16 MiB
- RAM: 128 MiB
- Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3
- Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4
- PHY: Atheros AR8035-A

Installation:
If you can get to the stock firmware's firmware upgrade option, just feed
it the factory.img and boot as usual. As an alternative, TFTP the
factory.img to the bootloader.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[whitespace fix in DTS and reorder of make variables]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit is contained in:
Daniel Gimpelevich 2018-09-13 21:08:51 -07:00 committed by Petr Štetiar
parent d75d4837fc
commit f61e754522
8 changed files with 282 additions and 0 deletions

View File

@ -20,6 +20,8 @@ buffalo,bhr-4grv2|\
glinet,gl-ar300m-nand|\
glinet,gl-ar300m-nor|\
librerouter,librerouter-v1|\
netgear,ex6400|\
netgear,ex7300|\
ocedo,koala|\
ocedo,raccoon|\
openmesh,om5p-ac-v2|\

View File

@ -14,6 +14,8 @@ ath79_setup_interfaces()
devolo,dvl1750c|\
devolo,dvl1750i|\
glinet,ar300m-lite|\
netgear,ex6400|\
netgear,ex7300|\
ocedo,koala|\
ocedo,raccoon|\
pcs,cap324|\

View File

@ -170,6 +170,11 @@ case "$FIRMWARE" in
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
netgear,ex6400|\
netgear,ex7300)
ath10kcal_extract "caldata" 20480 12064
ath10kcal_patch_mac $(mtd_get_mac_binary caldata 12)
;;
phicomm,k2t)
ath10kcal_extract "art" 20480 12064
ath10kcal_patch_mac_crc $(k2t_get_mac "5g_mac")

View File

@ -0,0 +1,9 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "qca9558_netgear_ex7300.dtsi"
/ {
model = "Netgear EX6400";
compatible = "netgear,ex6400", "qca,qca9558";
};

View File

@ -0,0 +1,9 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "qca9558_netgear_ex7300.dtsi"
/ {
model = "Netgear EX7300";
compatible = "netgear,ex7300", "qca,qca9558";
};

View File

@ -0,0 +1,222 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "qca9557.dtsi"
/ {
chosen {
bootargs = "console=ttyS0,115200n8";
};
aliases {
led-boot = &power_green;
led-failsafe = &power_amber;
led-running = &power_green;
led-upgrade = &power_amber;
};
led_spi {
compatible = "spi-gpio";
#address-cells = <1>;
#size-cells = <0>;
gpio-sck = <&gpio 18 GPIO_ACTIVE_HIGH>;
gpio-mosi = <&gpio 15 GPIO_ACTIVE_HIGH>;
num-chipselects = <0>;
led_gpio: led_gpio@0 {
compatible = "nxp,74lvc594";
reg = <0>;
gpio-controller;
#gpio-cells = <2>;
registers-number = <1>;
lines-initial-states = /bits/ 8 <0xff>;
spi-max-frequency = <500000>;
gpio_latch_bit {
gpio-hog;
gpios = <4 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "gpio-latch-bit";
};
};
};
leds {
compatible = "gpio-leds";
power_green: power_green {
label = "netgear:green:power";
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
};
power_amber: power_amber {
label = "netgear:amber:power";
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
};
left_blue {
label = "netgear:blue:left";
gpios = <&led_gpio 7 GPIO_ACTIVE_LOW>;
};
right_blue {
label = "netgear:blue:right";
gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>;
};
wps_green {
label = "netgear:green:wps";
gpios = <&led_gpio 5 GPIO_ACTIVE_LOW>;
};
client_red {
label = "netgear:red:client";
gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>;
};
client_green {
label = "netgear:green:client";
gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>;
};
router_red {
label = "netgear:red:router";
gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>;
};
router_green {
label = "netgear:green:router";
gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>;
};
};
keys {
compatible = "gpio-keys";
reset {
label = "Reset button";
linux,code = <KEY_RESTART>;
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
wps {
label = "WPS button";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
extender_apmode {
label = "EXTENDER/APMODE switch";
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
linux,code = <BTN_0>;
linux,input-type = <EV_SW>;
debounce-interval = <60>;
};
};
};
&pcie0 {
status = "okay";
};
&uart {
status = "okay";
};
&pll {
clocks = <&extosc>;
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
uboot: partition@0 {
label = "u-boot";
reg = <0x000000 0x040000>;
read-only;
};
partition@40000 {
label = "u-boot-env";
reg = <0x040000 0x010000>;
};
caldata: partition@50000 {
label = "caldata";
reg = <0x050000 0x010000>;
read-only;
};
partition@60000 {
label = "caldata-backup";
reg = <0x060000 0x010000>;
read-only;
};
partition@70000 {
label = "config";
reg = <0x070000 0x010000>;
};
partition@80000 {
label = "pot";
reg = <0x080000 0x010000>;
};
partition@90000 {
label = "firmware";
reg = <0x090000 0xf30000>;
compatible = "denx,uimage";
};
partition@fc0000 {
label = "language";
reg = <0xfc0000 0x040000>;
};
};
};
};
&wmac {
status = "okay";
mtd-cal-data = <&caldata 0x1000>;
mtd-mac-address = <&caldata 0x06>;
};
&mdio0 {
status = "okay";
phy4: ethernet-phy@4 {
reg = <4>;
phy-mode = "rgmii";
};
};
&eth0 {
status = "okay";
mtd-mac-address = <&caldata 0x00>;
phy-handle = <&phy4>;
phy-mode = "rgmii";
pll-data = <0x83000000 0x80000101 0x80001313>;
};

View File

@ -19,6 +19,16 @@ define Build/netgear-squashfs
rm -rf $@.squashfs $@.fs
endef
define Build/netgear-rootfs
mkimage \
-A mips -O linux -T filesystem -C none \
-M $(NETGEAR_KERNEL_MAGIC) \
-n '$(VERSION_DIST) filesystem' \
-d $(IMAGE_ROOTFS) $@.fs
cat $@.fs >> $@
rm -rf $@.fs
endef
define Build/netgear-uImage
$(call Build/uImage,$(1) -M $(NETGEAR_KERNEL_MAGIC))
endef

View File

@ -551,6 +551,29 @@ define Device/netgear_wndr3x00
$(Device/netgear_ath79)
endef
define Device/netgear_ex7300_ex6400
ATH_SOC := qca9558
NETGEAR_KERNEL_MAGIC := 0x27051956
NETGEAR_BOARD_ID := EX7300series
NETGEAR_HW_ID := 29765104+16+0+128
IMAGE_SIZE := 15552k
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | netgear-rootfs | pad-rootfs
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca99x0-ct
$(Device/netgear_ath79)
endef
define Device/netgear_ex6400
$(Device/netgear_ex7300_ex6400)
DEVICE_TITLE := NETGEAR EX6400
endef
TARGET_DEVICES += netgear_ex6400
define Device/netgear_ex7300
$(Device/netgear_ex7300_ex6400)
DEVICE_TITLE := NETGEAR EX7300
endef
TARGET_DEVICES += netgear_ex7300
define Device/netgear_wndr3700
$(Device/netgear_wndr3x00)
DEVICE_TITLE := NETGEAR WNDR3700