ramips: add support for I-O DATA WN-AC1167GR
I-O DATA WN-AC1167GR is a 2.4/5 GHz band 11ac router, based on MediaTek MT7620A. Specification: - SoC : MediaTek MT7620A - RAM : DDR2 64 MB - Flash : SPI-NOR 8MB - WLAN : 2.4/5 GHz, 2T2R - 2.4 GHz: MT7620A (SoC) - 5 GHz : MT7612E - Ethernet: 10/100/1000 Mbps (ext. MT7530) - LED/key : 4x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J2: TX, GND, RX, Vcc from SoC side - 115200n8 Flash instruction using factory image: 1. Boot WN-AC1167GR normaly 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This commit is contained in:
INAGAKI Hiroshi
Christian Lamparter
parent
dee8db441e
commit
f305ce5c35
|
|
@ -188,6 +188,10 @@ ht-tm02)
|
|||
ucidef_set_led_netdev "eth" "Ethernet" "$boardname:green:lan" "eth0"
|
||||
set_wifi_led "$boardname:blue:wlan"
|
||||
;;
|
||||
iodata,wn-ac1167gr)
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN5G" "$boardname:green:wlan5g" "phy0radio"
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2G" "$boardname:green:wlan2g" "phy1radio"
|
||||
;;
|
||||
kimax,u35wf)
|
||||
set_wifi_led "$boardname:blue:wifi"
|
||||
ucidef_set_led_netdev "eth" "ETH" "$boardname:green:eth" "eth0"
|
||||
|
|
|
|||
|
|
@ -319,6 +319,10 @@ ramips_setup_interfaces()
|
|||
ucidef_add_switch "switch0" \
|
||||
"1:lan" "2:lan" "3:lan" "4:lan" "5:lan" "0:wan" "6@eth0"
|
||||
;;
|
||||
iodata,wn-ac1167gr)
|
||||
ucidef_add_switch "switch1" \
|
||||
"1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "0:wan" "6@eth0"
|
||||
;;
|
||||
kn_rf)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6@eth0"
|
||||
|
|
@ -525,6 +529,9 @@ ramips_setup_macs()
|
|||
[ -n "$lan_mac" ] || lan_mac=$(cat /sys/class/net/eth0/address)
|
||||
wan_mac=$(macaddr_add "$lan_mac" 1)
|
||||
;;
|
||||
iodata,wn-ac1167gr)
|
||||
wan_mac=$(macaddr_add "$(mtd_get_mac_binary Factory 4)" -1)
|
||||
;;
|
||||
iodata,wn-ax1167gr|\
|
||||
iodata,wn-gx300gr)
|
||||
wan_mac=$(macaddr_add "$(mtd_get_mac_binary Factory 4)" 1)
|
||||
|
|
|
|||
|
|
@ -0,0 +1,216 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include "mt7620a.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
compatible = "iodata,wn-ac1167gr", "ralink,mt7620a-soc";
|
||||
model = "I-O DATA WN-AC1167GR";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_power;
|
||||
};
|
||||
|
||||
memory@0 {
|
||||
device_type = "memory";
|
||||
reg = <0x0 0x4000000>;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power: power {
|
||||
label = "wn-ac1167gr:green:power";
|
||||
gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
label = "wn-ac1167gr:green:wlan2g";
|
||||
gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
notification {
|
||||
label = "wn-ac1167gr:green:notification";
|
||||
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
label = "wn-ac1167gr:green:wlan5g";
|
||||
gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys-polled";
|
||||
poll-interval = <20>;
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
auto {
|
||||
label = "auto";
|
||||
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_0>;
|
||||
linux,input-type = <EV_SW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <10000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x30000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@30000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x30000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
Factory: partition@40000 {
|
||||
label = "Factory";
|
||||
reg = <0x40000 0x8000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
iNIC_rf: partition@48000 {
|
||||
label = "iNIC_rf";
|
||||
reg = <0x48000 0x8000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "NoUsed";
|
||||
reg = <0x50000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@70000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x70000 0x6b4000>;
|
||||
};
|
||||
|
||||
partition@724000 {
|
||||
label = "manufacture";
|
||||
reg = <0x724000 0x8c000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@7b0000 {
|
||||
label = "backup";
|
||||
reg = <0x7b0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@7c0000 {
|
||||
label = "storage";
|
||||
reg = <0x7c0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ðernet {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rgmii1_pins &mdio_pins>;
|
||||
mtd-mac-address = <&Factory 0x4>;
|
||||
|
||||
port@5 {
|
||||
status = "okay";
|
||||
mediatek,fixed-link = <1000 1 1 1>;
|
||||
phy-mode = "rgmii";
|
||||
};
|
||||
|
||||
mdio-bus {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "okay";
|
||||
|
||||
ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
phy-mode = "rgmii";
|
||||
};
|
||||
|
||||
ethernet-phy@1 {
|
||||
reg = <1>;
|
||||
phy-mode = "rgmii";
|
||||
};
|
||||
|
||||
ethernet-phy@2 {
|
||||
reg = <2>;
|
||||
phy-mode = "rgmii";
|
||||
};
|
||||
|
||||
ethernet-phy@3 {
|
||||
reg = <3>;
|
||||
phy-mode = "rgmii";
|
||||
};
|
||||
|
||||
ethernet-phy@4 {
|
||||
reg = <4>;
|
||||
phy-mode = "rgmii";
|
||||
};
|
||||
|
||||
ethernet-phy@1f {
|
||||
reg = <0x1f>;
|
||||
phy-mode = "rgmii";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
state_default: pinctrl0 {
|
||||
gpio {
|
||||
ralink,group = "i2c", "uartf";
|
||||
ralink,function = "gpio";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
wifi@0,0 {
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
mediatek,mtd-eeprom = <&iNIC_rf 0x0>;
|
||||
ieee80211-freq-limit = <5000000 6000000>;
|
||||
};
|
||||
};
|
||||
|
||||
&wmac {
|
||||
ralink,mtd-eeprom = <&Factory 0x0>;
|
||||
};
|
||||
|
|
@ -16,6 +16,25 @@ define Build/elecom-header
|
|||
-f $@ -C $(KDIR) v_0.0.0.bin v_0.0.0.md5
|
||||
endef
|
||||
|
||||
define Build/elx-header
|
||||
$(eval hw_id=$(word 1,$(1)))
|
||||
$(eval xor_pattern=$(word 2,$(1)))
|
||||
( \
|
||||
echo -ne "\x00\x00\x00\x00\x00\x00\x00\x03" | \
|
||||
dd bs=42 count=1 conv=sync; \
|
||||
hw_id="$(hw_id)"; \
|
||||
echo -ne "\x$${hw_id:0:2}\x$${hw_id:2:2}\x$${hw_id:4:2}\x$${hw_id:6:2}" | \
|
||||
dd bs=20 count=1 conv=sync; \
|
||||
echo -ne "$$(printf '%08x' $$(stat -c%s $@) | fold -s2 | xargs -I {} echo \\x{} | tr -d '\n')" | \
|
||||
dd bs=8 count=1 conv=sync; \
|
||||
echo -ne "$$($(STAGING_DIR_HOST)/bin/mkhash md5 $@ | fold -s2 | xargs -I {} echo \\x{} | tr -d '\n')" | \
|
||||
dd bs=58 count=1 conv=sync; \
|
||||
) > $(KDIR)/tmp/$(DEVICE_NAME).header
|
||||
$(call Build/xor-image,-p $(xor_pattern) -x)
|
||||
cat $(KDIR)/tmp/$(DEVICE_NAME).header $@ > $@.new
|
||||
mv $@.new $@
|
||||
endef
|
||||
|
||||
define Device/ai-br100
|
||||
DTS := AI-BR100
|
||||
IMAGE_SIZE := 7936k
|
||||
|
|
@ -327,6 +346,18 @@ define Device/hc5861
|
|||
endef
|
||||
TARGET_DEVICES += hc5861
|
||||
|
||||
define Device/iodata_wn-ac1167gr
|
||||
DTS := WN-AC1167GR
|
||||
DEVICE_TITLE := I-O DATA WN-AC1167GR
|
||||
IMAGE_SIZE := 6864k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := \
|
||||
$$(sysupgrade_bin) | check-size $$$$(IMAGE_SIZE) | \
|
||||
elx-header 01040016 8844A2D168B45A2D
|
||||
DEVICE_PACKAGES := kmod-mt76x2
|
||||
endef
|
||||
TARGET_DEVICES += iodata_wn-ac1167gr
|
||||
|
||||
define Device/kimax_u35wf
|
||||
DTS := U35WF
|
||||
IMAGE_SIZE := 16064k
|
||||
|
|
|
|||
Loading…
Reference in New Issue