mediatek: filogic: add Qihoo 360T7 support
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: ESMT F50L1G41LB 128MB
RAM: MT5CC128M16JR-EK 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS
Power: DC 12V 1A
Flash instructions:
1. Attach UART, boot the stock firmware until
the message about failsafe mode appears.
2. Enter failsafe mode by pressing "f" and "Enter"
3. Type "mount_root", then run
"fw_setenv bootmenu_delay 3"
4. Back up all mtd partitions before flashing.
5. Reboot, U-Boot now presents a menu.
6. Connect to your PC via the Gigabit port of the router,
set a static ip on the ethernet interface of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
7. Select "Upgrade ATF BL2", then use this file:
openwrt-mediatek-filogic-qihoo_360t7-preloader.bin
8. Select "Upgrade ATF FIP", then use this file:
openwrt-mediatek-filogic-qihoo_360t7-bl31-uboot.fip
9. Download the initramfs image, and type "reset",
waiting for tftp recovery to complete.
a. After openwrt boots up, perform sysupgrade.
Note:
1. Since NMBM is disabled, we must back up all partitions.
2. Flash instructions is based on commit 28df7f7.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
This commit is contained in:
Chukun Pan
Daniel Golle
parent
c51eb17730
commit
dc2d4d7393
|
|
@ -0,0 +1,229 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/dts-v1/;
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "mt7981.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Qihoo 360T7";
|
||||
compatible = "qihoo,360t7", "mediatek,mt7981";
|
||||
|
||||
aliases {
|
||||
serial0 = &uart0;
|
||||
led-boot = &led_status_red;
|
||||
led-failsafe = &led_status_red;
|
||||
led-running = &led_status_green;
|
||||
led-upgrade = &led_status_green;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
memory {
|
||||
reg = <0 0x40000000 0 0x10000000>;
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&pio 0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_status_red: red {
|
||||
label = "red:status";
|
||||
gpios = <&pio 3 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_status_green: green {
|
||||
label = "green:status";
|
||||
gpios = <&pio 7 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð {
|
||||
status = "okay";
|
||||
|
||||
gmac0: mac@0 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio_bus {
|
||||
switch: switch@0 {
|
||||
compatible = "mediatek,mt7531";
|
||||
reg = <31>;
|
||||
reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-parent = <&pio>;
|
||||
interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi0_flash_pins>;
|
||||
status = "okay";
|
||||
|
||||
spi_nand@0 {
|
||||
compatible = "spi-nand";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
reg = <0>;
|
||||
|
||||
spi-max-frequency = <52000000>;
|
||||
spi-tx-buswidth = <4>;
|
||||
spi-rx-buswidth = <4>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "bl2";
|
||||
reg = <0x0000000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x0100000 0x0080000>;
|
||||
};
|
||||
|
||||
factory: partition@180000 {
|
||||
label = "Factory";
|
||||
reg = <0x0180000 0x0200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@380000 {
|
||||
label = "fip";
|
||||
reg = <0x0380000 0x0200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@580000 {
|
||||
label = "ubi";
|
||||
reg = <0x0580000 0x6c00000>;
|
||||
};
|
||||
|
||||
partition@7180000 {
|
||||
label = "config";
|
||||
reg = <0x7180000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@7280000 {
|
||||
label = "factory";
|
||||
reg = <0x7280000 0x0080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@7300000 {
|
||||
label = "log";
|
||||
reg = <0x7300000 0x0700000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&switch {
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
label = "lan3";
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
port@3 {
|
||||
reg = <3>;
|
||||
label = "wan";
|
||||
};
|
||||
|
||||
port@6 {
|
||||
reg = <6>;
|
||||
ethernet = <&gmac0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pio {
|
||||
spi0_flash_pins: spi0-pins {
|
||||
mux {
|
||||
function = "spi";
|
||||
groups = "spi0", "spi0_wp_hold";
|
||||
};
|
||||
|
||||
conf-pu {
|
||||
pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
|
||||
drive-strength = <8>;
|
||||
mediatek,pull-up-adv = <0>; /* bias-disable */
|
||||
};
|
||||
|
||||
conf-pd {
|
||||
pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
|
||||
drive-strength = <8>;
|
||||
mediatek,pull-up-adv = <0>; /* bias-disable */
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi {
|
||||
status = "okay";
|
||||
|
||||
mediatek,mtd-eeprom = <&factory 0x0>;
|
||||
};
|
||||
|
|
@ -29,6 +29,9 @@ mediatek_setup_interfaces()
|
|||
mediatek,mt7988a-dsa-10g-spim-snand)
|
||||
ucidef_set_interfaces_lan_wan "lan0 lan1 lan2 lan3" "eth1 eth2"
|
||||
;;
|
||||
qihoo,360t7)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" wan
|
||||
;;
|
||||
tplink,tl-xdr4288|\
|
||||
tplink,tl-xdr6088)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5" eth1
|
||||
|
|
@ -63,6 +66,11 @@ mediatek_setup_macs()
|
|||
bananapi,bpi-r3)
|
||||
wan_mac=$(macaddr_add $(cat /sys/class/net/eth0/address) 1)
|
||||
;;
|
||||
qihoo,360t7)
|
||||
lan_mac=$(mtd_get_mac_ascii factory lanMac)
|
||||
wan_mac=$(macaddr_add "$lan_mac" 1)
|
||||
label_mac=$wan_mac
|
||||
;;
|
||||
xiaomi,redmi-router-ax6000-stock|\
|
||||
xiaomi,redmi-router-ax6000-ubootmod)
|
||||
wan_mac=$(mtd_get_mac_ascii Bdata ethaddr_wan)
|
||||
|
|
|
|||
|
|
@ -32,6 +32,11 @@ case "$board" in
|
|||
[ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress
|
||||
[ "$PHYNBR" = "1" ] && macaddr_setbit_la $(macaddr_add $addr 1) > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
qihoo,360t7)
|
||||
addr=$(mtd_get_mac_ascii factory lanMac)
|
||||
[ "$PHYNBR" = "0" ] && macaddr_add $addr 2 > /sys${DEVPATH}/macaddress
|
||||
[ "$PHYNBR" = "1" ] && macaddr_add $addr 3 > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
tplink,tl-xdr4288|\
|
||||
tplink,tl-xdr6086|\
|
||||
tplink,tl-xdr6088)
|
||||
|
|
|
|||
|
|
@ -70,6 +70,7 @@ platform_do_upgrade() {
|
|||
cudy,wr3000-v1)
|
||||
default_do_upgrade "$1"
|
||||
;;
|
||||
qihoo,360t7|\
|
||||
tplink,tl-xdr4288|\
|
||||
tplink,tl-xdr6086|\
|
||||
tplink,tl-xdr6088|\
|
||||
|
|
|
|||
|
|
@ -233,6 +233,30 @@ define Device/mediatek_mt7988a-rfb-nand
|
|||
endef
|
||||
TARGET_DEVICES += mediatek_mt7988a-rfb-nand
|
||||
|
||||
define Device/qihoo_360t7
|
||||
DEVICE_VENDOR := Qihoo
|
||||
DEVICE_MODEL := 360T7
|
||||
DEVICE_DTS := mt7981b-qihoo-360t7
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
UBINIZE_OPTS := -E 5
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
KERNEL_IN_UBI := 1
|
||||
UBOOTENV_IN_UBI := 1
|
||||
IMAGES := sysupgrade.itb
|
||||
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
|
||||
KERNEL := kernel-bin | gzip
|
||||
KERNEL_INITRAMFS := kernel-bin | lzma | \
|
||||
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
|
||||
IMAGE/sysupgrade.itb := append-kernel | \
|
||||
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
|
||||
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
|
||||
ARTIFACTS := preloader.bin bl31-uboot.fip
|
||||
ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3
|
||||
ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot qihoo_360t7
|
||||
endef
|
||||
TARGET_DEVICES += qihoo_360t7
|
||||
|
||||
define Device/tplink_tl-xdr-common
|
||||
DEVICE_VENDOR := TP-Link
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
|
|
|
|||
Loading…
Reference in New Issue