ath79: add support for TP-Link TL-WR941HP v1

Specifications:
    SOC:        Qualcomm Atheros TP9343 (750 MHz)
    Flash:      8 Mb (GigaDevice GD25Q64CSIG)
    RAM:        64 Mb (Zentel A3R12E40DBF-8E)
    Serial:     yes, 4-pin header
    Wlan:       Qualcomm Atheros TP9343, antenna: MIM0 3x3:3 RP-SMA
                3 x 2.4GHz power amp module Skyworks (SiGe) SE2576L
    Ethernet:   Qualcomm Atheros TP9343
    Lan speed:  100M ports: 4
    Lan speed:  100M ports: 1
    Other info: same case, ram and flash that TP-Link TL-WR841HP,
                different SOC

    https://forum.openwrt.org/t/adding-device-support-tp-link-wr941hp/

Label MAC addresses based on vendor firmware:
    LAN   *:ee  label
    WAN   *:ef  label +1
    WLAN  *:ee  label

    The label MAC address found in "config" partition at 0x8

Flash instruction:
    Upload the generated factory firmware on web interface.

Signed-off-by: Diogenes Rengo <rengocbx250@gmail.com>
[remove various whitespace issues, squash commits, use short 0x0]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit is contained in:
Diogenes Rengo 2021-06-25 11:44:40 -03:00 committed by Adrian Schmutzler
parent 12eb5b2384
commit cce2e8db56
5 changed files with 201 additions and 1 deletions

View File

@ -0,0 +1,154 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "qca956x.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "tplink,tl-wr941hp-v1", "qca,tp9343";
model = "TP-Link TL-WR941HP v1";
aliases {
label-mac-device = &wmac;
led-boot = &led_power;
led-failsafe = &led_power;
led-running = &led_power;
led-upgrade = &led_power;
};
leds {
compatible = "gpio-leds";
re {
label = "blue:re";
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
};
wifi {
label = "blue:wifi";
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
led_power: power {
label = "blue:power";
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
default-state = "on";
};
wan_blue {
label = "blue:wan";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
};
wan_red {
label = "red:wan";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
};
lan {
label = "blue:lan";
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
};
wps {
label = "blue:wps";
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
};
};
keys {
compatible = "gpio-keys";
re {
label = "range extender button";
linux,code = <BTN_0>;
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
wifi {
label = "wifi button";
linux,code = <KEY_RFKILL>;
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
reset {
label = "reset button";
linux,code = <KEY_RESTART>;
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
wps {
label = "wps button";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
};
&spi {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
uboot: partition@0 {
label = "u-boot";
reg = <0x0 0x020000>;
read-only;
};
partition@20000 {
compatible = "tplink,firmware";
label = "firmware";
reg = <0x020000 0x730000>;
};
config: partition@750000 {
label = "config";
reg = <0x750000 0x0a0000>;
read-only;
};
art: partition@7f0000 {
label = "art";
reg = <0x7f0000 0x010000>;
read-only;
};
};
};
};
&eth0 {
status = "okay";
phy-handle = <&swphy0>;
mtd-mac-address = <&config 0x8>;
mtd-mac-address-increment = <1>;
};
&eth1 {
status = "okay";
mtd-mac-address = <&config 0x8>;
};
&wmac {
status = "okay";
mtd-cal-data = <&art 0x1000>;
mtd-mac-address = <&config 0x8>;
};

View File

@ -374,6 +374,10 @@ tplink,tl-wr842n-v2)
ucidef_set_led_switch "lan3" "LAN3" "green:lan3" "switch0" "0x10"
ucidef_set_led_switch "lan4" "LAN4" "green:lan4" "switch0" "0x02"
;;
tplink,tl-wr941hp-v1)
ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth1" "link tx rx"
ucidef_set_led_switch "lan" "LAN" "blue:lan" "switch0" "0x1e"
;;
trendnet,tew-823dru)
ucidef_set_led_netdev "wan" "WAN" "green:planet" "eth0"
;;

View File

@ -398,7 +398,8 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "5:lan:4"
;;
tplink,tl-wr842n-v2)
tplink,tl-wr842n-v2)\
tplink,tl-wr941hp-v1)
ucidef_set_interface_wan "eth1"
ucidef_add_switch "switch0" \
"0@eth0" "1:lan:4" "2:lan:1" "3:lan:2" "4:lan:3"

View File

@ -798,6 +798,16 @@ define Device/tplink_tl-wr902ac-v1
endef
TARGET_DEVICES += tplink_tl-wr902ac-v1
define Device/tplink_tl-wr941hp-v1
$(Device/tplink-safeloader)
SOC := tp9343
DEVICE_MODEL := TL-WR941HP
DEVICE_VARIANT := v1
TPLINK_BOARD_ID := TL-WR941HP-V1
IMAGE_SIZE := 7360k
endef
TARGET_DEVICES += tplink_tl-wr941hp-v1
define Device/tplink_wbs210-v1
$(Device/tplink-safeloader-okli)
SOC := ar9344

View File

@ -1930,6 +1930,37 @@ static struct device_info boards[] = {
.last_sysupgrade_partition = "file-system",
},
/** Firmware layout for the TL-WR941HP v1 */
{
.id = "TL-WR941HP-V1",
.vendor = "",
.support_list =
"SupportList:\n"
"{product_name:TL-WR941HP,product_ver:1.0.0,special_id:00000000}\n",
.part_trail = 0x00,
.soft_ver = NULL,
.partitions = {
{"fs-uboot", 0x00000, 0x20000},
{"firmware", 0x20000, 0x730000},
{"default-mac", 0x750000, 0x00200},
{"pin", 0x750200, 0x00200},
{"product-info", 0x750400, 0x0fc00},
{"soft-version", 0x760000, 0x0b000},
{"support-list", 0x76b000, 0x04000},
{"profile", 0x770000, 0x04000},
{"default-config", 0x774000, 0x0b000},
{"user-config", 0x780000, 0x40000},
{"partition-table", 0x7c0000, 0x10000},
{"log", 0x7d0000, 0x20000},
{"radio", 0x7f0000, 0x10000},
{NULL, 0, 0}
},
.first_sysupgrade_partition = "os-image",
.last_sysupgrade_partition = "file-system",
},
/** Firmware layout for the TL-WR942N V1 */
{
.id = "TLWR942NV1",