mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2024-06-16 04:03:56 +02:00
mediatek: add support for Zbtlink ZBT-Z8102AX
Specifications: SoC: MediaTek MT7981B RAM: 1024MiB Flash: SPI-NAND 128 MiB Switch: 1 WAN, 4 LAN (Gigabit) USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port Buttons: Reset, Mesh Power: DC 12V 1A WiFi: MT7976CN UART: 115200n8 UART Layout: VCC-RX-TX-GND Installation: A. Through OpenWrt Dashboard: If your router comes with OpenWrt preinstalled (modified by the seller), you can easily upgrade by going to the dashboard (192.168.1.1) and then navigate to System -> Backup/Flash firmware, then flash the firmware B. Through TFTP Standard installation via UART: 1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin). 2. Power on the router. Make sure that you can access your router via UART. 3. Restart the router then repeatedly press ctrl + c to skip default boot. 4. Type > bootmenu 5. Press '2' to select upgrade firmware 6. Press 'Y' on 'Run image after upgrading?' 7. Press '0' and hit 'enter' to select TFTP client (default) 8. Fill the U-Boot's IP address and TFTP server's IP address. 9. Finally, enter the 'firmware' filename. Based on patch adding support for similar Zbtlink ZBT-Z8103AX device by Ian Ishmael C. Oderon. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This commit is contained in:
Daniel Golle
parent
6f5c301eab
commit
c8c2f52262
|
|
@ -66,7 +66,8 @@ mercusys,mr90x-v1)
|
|||
ubootenv_add_uci_config "$envdev" "0x0" "0x20000" "0x20000" "1"
|
||||
;;
|
||||
cetron,ct3003|\
|
||||
netgear,wax220)
|
||||
netgear,wax220|\
|
||||
zbtlink,zbt-z8102ax)
|
||||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000"
|
||||
;;
|
||||
ubnt,unifi-6-plus)
|
||||
|
|
|
|||
332
target/linux/mediatek/dts/mt7981b-zbtlink-zbt-z8102ax.dts
Normal file
332
target/linux/mediatek/dts/mt7981b-zbtlink-zbt-z8102ax.dts
Normal file
|
|
@ -0,0 +1,332 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "mt7981.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Zbtlink ZBT-Z8102AX";
|
||||
compatible = "zbtlink,zbt-z8102ax", "mediatek,mt7981";
|
||||
|
||||
aliases {
|
||||
serial0 = &uart0;
|
||||
led-boot = &led_status_green;
|
||||
led-failsafe = &led_status_red;
|
||||
led-running = &led_status_green;
|
||||
led-upgrade = &led_status_green;
|
||||
label-mac-device = &gmac0;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n8 loglevel=8";
|
||||
};
|
||||
|
||||
memory {
|
||||
reg = <0 0x40000000 0 0x40000000>;
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
button-reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
button-mesh {
|
||||
label = "mesh";
|
||||
linux,code = <BTN_0>;
|
||||
gpios = <&pio 0 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
button-hub {
|
||||
label = "hub";
|
||||
linux,code = <BTN_1>;
|
||||
gpios = <&pio 12 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_status_red: red {
|
||||
label = "red:status";
|
||||
gpios = <&pio 9 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_STATUS;
|
||||
};
|
||||
|
||||
led_status_green: green {
|
||||
label = "green:status";
|
||||
gpios = <&pio 10 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_STATUS;
|
||||
};
|
||||
|
||||
blue {
|
||||
label = "blue:status";
|
||||
gpios = <&pio 11 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_STATUS;
|
||||
};
|
||||
|
||||
4g {
|
||||
label = "blue:4g";
|
||||
gpios = <&pio 8 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_USB;
|
||||
function-enumerator = <0>;
|
||||
};
|
||||
|
||||
4g2 {
|
||||
label = "blue:4g2";
|
||||
gpios = <&pio 14 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_USB;
|
||||
function-enumerator = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
watchdog {
|
||||
compatible = "linux,wdt-gpio";
|
||||
gpios = <&pio 2 GPIO_ACTIVE_HIGH>;
|
||||
hw_algo = "toggle";
|
||||
hw_margin_ms = <1000>;
|
||||
};
|
||||
|
||||
gpio-export {
|
||||
compatible = "gpio-export";
|
||||
#size-cells = <0>;
|
||||
|
||||
pcie {
|
||||
gpio-export,name = "pcie_power";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&pio 3 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
5g1 {
|
||||
gpio-export,name = "5g1";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&pio 4 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
5g2 {
|
||||
gpio-export,name = "5g2";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
sim1 {
|
||||
gpio-export,name = "sim1";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&pio 6 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
sim2 {
|
||||
gpio-export,name = "sim2";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð {
|
||||
status = "okay";
|
||||
|
||||
gmac0: mac@0 {
|
||||
/* LAN */
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <0>;
|
||||
phy-mode = "2500base-x";
|
||||
phy-handle = <&phy0>;
|
||||
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&macaddr_factory_4 2>;
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
|
||||
gmac1: mac@1 {
|
||||
/* WAN */
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <1>;
|
||||
phy-mode = "gmii";
|
||||
phy-handle = <&int_gbe_phy>;
|
||||
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&macaddr_factory_4 3>;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio_bus {
|
||||
switch: switch@1f {
|
||||
compatible = "mediatek,mt7531";
|
||||
reg = <0x1f>;
|
||||
reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-parent = <&pio>;
|
||||
interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi0_flash_pins>;
|
||||
status = "okay";
|
||||
|
||||
spi_nand@0 {
|
||||
compatible = "spi-nand";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
reg = <0>;
|
||||
|
||||
spi-max-frequency = <52000000>;
|
||||
spi-tx-bus-width = <4>;
|
||||
spi-rx-bus-width = <4>;
|
||||
|
||||
mediatek,nmbm;
|
||||
mediatek,bmt-max-ratio = <1>;
|
||||
mediatek,bmt-max-reserved-blocks = <64>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "bl2";
|
||||
reg = <0x0000000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x100000 0x80000>;
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
label = "Factory";
|
||||
reg = <0x180000 0x200000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
eeprom_factory: eeprom@0 {
|
||||
reg = <0x0 0x1000>;
|
||||
};
|
||||
|
||||
macaddr_factory_4: macaddr@4 {
|
||||
compatible = "mac-base";
|
||||
reg = <0x4 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@380000 {
|
||||
label = "FIP";
|
||||
reg = <0x380000 0x200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@580000 {
|
||||
label = "ubi";
|
||||
reg = <0x580000 0x4000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&switch {
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
label = "lan3";
|
||||
};
|
||||
|
||||
port@3 {
|
||||
reg = <3>;
|
||||
label = "lan4";
|
||||
};
|
||||
|
||||
port@6 {
|
||||
reg = <6>;
|
||||
label = "cpu";
|
||||
ethernet = <&gmac0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pio {
|
||||
spi0_flash_pins: spi0-pins {
|
||||
mux {
|
||||
function = "spi";
|
||||
groups = "spi0", "spi0_wp_hold";
|
||||
};
|
||||
|
||||
conf-pu {
|
||||
pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up = <103>;
|
||||
};
|
||||
|
||||
conf-pd {
|
||||
pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
|
||||
drive-strength = <8>;
|
||||
bias-pull-down = <103>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&xhci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi {
|
||||
status = "okay";
|
||||
|
||||
nvmem-cells = <&eeprom_factory>;
|
||||
nvmem-cell-names = "eeprom";
|
||||
};
|
||||
|
|
@ -12,7 +12,8 @@ mediatek_setup_interfaces()
|
|||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 game" eth1
|
||||
;;
|
||||
asus,tuf-ax4200|\
|
||||
mediatek,mt7981-rfb)
|
||||
mediatek,mt7981-rfb|\
|
||||
zbtlink,zbt-z8102ax)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" eth1
|
||||
;;
|
||||
asus,tuf-ax6000)
|
||||
|
|
|
|||
|
|
@ -0,0 +1,19 @@
|
|||
. /lib/functions/uci-defaults.sh
|
||||
|
||||
board_config_update
|
||||
|
||||
board=$(board_name)
|
||||
|
||||
case "$board" in
|
||||
zbtlink,zbt-z8103ax)
|
||||
ucidef_add_gpio_switch "5g1" "Power 1st modem" "5g1" "1"
|
||||
ucidef_add_gpio_switch "5g2" "Power 2nd modem" "5g2" "1"
|
||||
ucidef_add_gpio_switch "pcie" "Power PCIe port" "pcie" "1"
|
||||
ucidef_add_gpio_switch "sim1" "SIM 1" "sim1" "1"
|
||||
ucidef_add_gpio_switch "sim2" "SIM 2" "sim2" "1"
|
||||
;;
|
||||
esac
|
||||
|
||||
board_config_flush
|
||||
|
||||
exit 0
|
||||
|
|
@ -95,6 +95,7 @@ case "$board" in
|
|||
tplink,tl-xdr6088)
|
||||
[ "$PHYNBR" = "0" ] && get_mac_label > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
zbtlink,zbt-z8102ax|\
|
||||
zyxel,ex5601-t0)
|
||||
addr=$(mtd_get_mac_binary "Factory" 0x4)
|
||||
[ "$PHYNBR" = "1" ] && macaddr_add $addr 1 > /sys${DEVPATH}/macaddress
|
||||
|
|
|
|||
|
|
@ -169,6 +169,8 @@ CONFIG_GENERIC_STRNLEN_USER=y
|
|||
CONFIG_GENERIC_TIME_VSYSCALL=y
|
||||
CONFIG_GLOB=y
|
||||
CONFIG_GPIO_CDEV=y
|
||||
CONFIG_GPIO_WATCHDOG=y
|
||||
CONFIG_GPIO_WATCHDOG_ARCH_INITCALL=y
|
||||
CONFIG_GRO_CELLS=y
|
||||
CONFIG_HANDLE_DOMAIN_IRQ=y
|
||||
CONFIG_HARDIRQS_SW_RESEND=y
|
||||
|
|
|
|||
|
|
@ -187,6 +187,8 @@ CONFIG_GENERIC_STRNLEN_USER=y
|
|||
CONFIG_GENERIC_TIME_VSYSCALL=y
|
||||
CONFIG_GLOB=y
|
||||
CONFIG_GPIO_CDEV=y
|
||||
CONFIG_GPIO_WATCHDOG=y
|
||||
CONFIG_GPIO_WATCHDOG_ARCH_INITCALL=y
|
||||
CONFIG_GRO_CELLS=y
|
||||
CONFIG_HARDIRQS_SW_RESEND=y
|
||||
CONFIG_HAS_DMA=y
|
||||
|
|
|
|||
|
|
@ -728,6 +728,23 @@ endif
|
|||
endef
|
||||
TARGET_DEVICES += xiaomi_redmi-router-ax6000-ubootmod
|
||||
|
||||
define Device/zbtlink_zbt-z8102ax
|
||||
DEVICE_VENDOR := Zbtlink
|
||||
DEVICE_MODEL := ZBT-Z8102AX
|
||||
DEVICE_DTS := mt7981b-zbtlink-zbt-z8102ax
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware kmod-usb-net-qmi-wwan kmod-usb-serial-option
|
||||
KERNEL_IN_UBI := 1
|
||||
UBINIZE_OPTS := -E 5
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGE_SIZE := 65536k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-ubi | check-size $$(IMAGE_SIZE)
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += zbtlink_zbt-z8102ax
|
||||
|
||||
define Device/zyxel_ex5601-t0-stock
|
||||
DEVICE_VENDOR := Zyxel
|
||||
DEVICE_MODEL := EX5601-T0 (stock layout)
|
||||
|
|
|
|||
Loading…
Reference in New Issue
Block a user