mvebu: add support for iEi Puzzle-M901/Puzzle-M902
Hardware specification
----------------------
* CN9130 SoC, Quad-core ARMv8 Cortex-72 @ 2200 MHz
* 4 GB DDR
* 4 GB eMMC
* mmcblk0
- mmcblk0p1 64M kernel_1
- mmcblk0p2 64M kernel_2
- mmcblk0p3 512M rootfs_1
- mmcblk0p4 512M rootfs_2
- mmcblk0p5 512M Reserved
- mmcblk0p6 64M Reserved
- mmcblk0p7 1.8G rootfs_data
* 4 MB (SPI Flash)
* 6 x 2.5 Gigabit ports (Puzzle-M901)
- External PHY with 6 ports (AQR112R)
* 6 x 2.5 Gigabit ports (Puzzle-M902)
- External PHY with 6 ports (AQR112R)
3 x 10 Gigabit ports (Puzzle-M902)
- External PHY with 3 ports (AQR113R)
* 4 x Front panel LED
* 1 x USB 3.0
* Reset button on Rear panel
* UART (115200 8N1,header on PCB)
Flash instructions:
The original firmware is based on OpenWrt.
Flash firmware using LuCI and CLI
Signed-off-by: Ian Chang <ianchang@ieiworld.com>
(cherry picked from commit 70c75965a9)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This commit is contained in:
Ian Chang
Daniel Golle
parent
bb1eb5e8e6
commit
c43a5921fa
|
|
@ -11,6 +11,12 @@ board_config_update
|
|||
board=$(board_name)
|
||||
|
||||
case "$board" in
|
||||
iei,puzzle-m901)
|
||||
ucidef_set_interfaces_lan_wan "eth1 eth2 eth3 eth4 eth5" "eth0"
|
||||
;;
|
||||
iei,puzzle-m902)
|
||||
ucidef_set_interfaces_lan_wan "eth1 eth2 eth3 eth4 eth5 eth10 eth11 eth12" "eth0"
|
||||
;;
|
||||
marvell,armada8040-mcbin-doubleshot|\
|
||||
marvell,armada8040-mcbin-singleshot)
|
||||
ucidef_set_interfaces_lan_wan "eth0 eth1 eth3" "eth2"
|
||||
|
|
|
|||
|
|
@ -0,0 +1,36 @@
|
|||
platform_do_upgrade_emmc() {
|
||||
local board=$(board_name)
|
||||
local diskdev partdev
|
||||
|
||||
export_bootdevice && export_partdevice diskdev 0 || {
|
||||
v "Unable to determine upgrade device"
|
||||
return 1
|
||||
}
|
||||
sync
|
||||
if [ "$UPGRADE_OPT_SAVE_PARTITIONS" = "1" ]; then
|
||||
get_partitions "/dev/$diskdev" bootdisk
|
||||
v "Extract boot sector from the image"
|
||||
get_image_dd "$1" of=/tmp/image.bs count=1 bs=512b
|
||||
get_partitions /tmp/image.bs image
|
||||
fi
|
||||
|
||||
#iterate over each partition from the image and write it to the boot disk
|
||||
while read part start size; do
|
||||
if export_partdevice partdev $part; then
|
||||
if [ "$partdev" = "mmcblk0p2" ]; then
|
||||
v "Writing image mmcblk0p3 for /dev/$partdev $start $size"
|
||||
get_image_dd "$1" of="/dev/mmcblk0p3" ibs="512" obs=1M skip="$start" count="$size" conv=fsync
|
||||
elif [ "$partdev" = "mmcblk0p1" ]; then
|
||||
v "Writing image mmcblk0p1 for /dev/$partdev $start $size"
|
||||
get_image_dd "$1" of="/dev/$partdev" ibs="512" obs=1M skip="$start" count="$size" conv=fsync
|
||||
fi
|
||||
else
|
||||
v "Unable to find partition $part device, skipped."
|
||||
fi
|
||||
done < /tmp/partmap.image
|
||||
|
||||
v "Writing new UUID to /dev/$diskdev..."
|
||||
get_image_dd "$1" of="/dev/$diskdev" bs=1 skip=440 count=4 seek=440 conv=fsync
|
||||
|
||||
sleep 1
|
||||
}
|
||||
|
|
@ -9,6 +9,8 @@ REQUIRE_IMAGE_METADATA=1
|
|||
|
||||
platform_check_image() {
|
||||
case "$(board_name)" in
|
||||
iei,puzzle-m901|\
|
||||
iei,puzzle-m902|\
|
||||
marvell,armada8040-mcbin-doubleshot|\
|
||||
marvell,armada8040-mcbin-singleshot)
|
||||
platform_check_image_sdcard "$1"
|
||||
|
|
@ -21,6 +23,10 @@ platform_check_image() {
|
|||
|
||||
platform_do_upgrade() {
|
||||
case "$(board_name)" in
|
||||
iei,puzzle-m901|\
|
||||
iei,puzzle-m902)
|
||||
platform_do_upgrade_emmc "$1"
|
||||
;;
|
||||
marvell,armada8040-mcbin-doubleshot|\
|
||||
marvell,armada8040-mcbin-singleshot)
|
||||
platform_do_upgrade_sdcard "$1"
|
||||
|
|
@ -32,6 +38,8 @@ platform_do_upgrade() {
|
|||
}
|
||||
platform_copy_config() {
|
||||
case "$(board_name)" in
|
||||
iei,puzzle-m901|\
|
||||
iei,puzzle-m902|\
|
||||
marvell,armada8040-mcbin-doubleshot|\
|
||||
marvell,armada8040-mcbin-singleshot)
|
||||
platform_copy_config_sdcard
|
||||
|
|
|
|||
|
|
@ -0,0 +1,319 @@
|
|||
// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
|
||||
/*
|
||||
* Copyright (C) 2019 Marvell International Ltd.
|
||||
*
|
||||
* Device tree for the CN9131-DB board.
|
||||
*/
|
||||
|
||||
#include "cn9130.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
|
||||
/ {
|
||||
model = "iEi Puzzle-M901";
|
||||
compatible = "iei,puzzle-m901",
|
||||
"marvell,armada-ap807-quad", "marvell,armada-ap807";
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
aliases {
|
||||
i2c0 = &cp1_i2c0;
|
||||
i2c1 = &cp0_i2c0;
|
||||
ethernet0 = &cp0_eth0;
|
||||
ethernet1 = &cp0_eth1;
|
||||
ethernet2 = &cp0_eth2;
|
||||
ethernet3 = &cp1_eth0;
|
||||
ethernet4 = &cp1_eth1;
|
||||
ethernet5 = &cp1_eth2;
|
||||
gpio1 = &cp0_gpio1;
|
||||
gpio2 = &cp0_gpio2;
|
||||
gpio3 = &cp1_gpio1;
|
||||
gpio4 = &cp1_gpio2;
|
||||
};
|
||||
|
||||
memory@00000000 {
|
||||
device_type = "memory";
|
||||
reg = <0x0 0x0 0x0 0x80000000>;
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cp0_uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/* on-board eMMC - U9 */
|
||||
&ap_sdhci0 {
|
||||
pinctrl-names = "default";
|
||||
bus-width = <8>;
|
||||
status = "okay";
|
||||
mmc-ddr-1_8v;
|
||||
mmc-hs400-1_8v;
|
||||
};
|
||||
|
||||
&cp0_crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cp0_xmdio {
|
||||
status = "okay";
|
||||
cp0_nbaset_phy0: ethernet-phy@0 {
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
reg = <2>;
|
||||
};
|
||||
cp0_nbaset_phy1: ethernet-phy@1 {
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
reg = <0>;
|
||||
};
|
||||
cp0_nbaset_phy2: ethernet-phy@2 {
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
reg = <8>;
|
||||
};
|
||||
};
|
||||
|
||||
&cp0_ethernet {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/* SLM-1521-V2, CON9 */
|
||||
&cp0_eth0 {
|
||||
status = "okay";
|
||||
phy-mode = "2500base-x";
|
||||
phys = <&cp0_comphy2 0>;
|
||||
managed = "in-band-status";
|
||||
};
|
||||
|
||||
&cp0_eth1 {
|
||||
status = "okay";
|
||||
phy-mode = "2500base-x";
|
||||
phys = <&cp0_comphy4 1>;
|
||||
managed = "in-band-status";
|
||||
};
|
||||
|
||||
&cp0_eth2 {
|
||||
status = "okay";
|
||||
phy-mode = "2500base-x";
|
||||
phys = <&cp0_comphy5 2>;
|
||||
managed = "in-band-status";
|
||||
};
|
||||
|
||||
&cp0_gpio1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cp0_gpio2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cp0_i2c0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&cp0_i2c0_pins>;
|
||||
status = "okay";
|
||||
clock-frequency = <100000>;
|
||||
rtc@32 {
|
||||
compatible = "epson,rx8130";
|
||||
reg = <0x32>;
|
||||
wakeup-source;
|
||||
};
|
||||
};
|
||||
|
||||
/* SLM-1521-V2, CON6 */
|
||||
&cp0_pcie0 {
|
||||
status = "okay";
|
||||
num-lanes = <2>;
|
||||
num-viewport = <8>;
|
||||
phys = <&cp0_comphy0 0>, <&cp0_comphy1 0>;
|
||||
};
|
||||
|
||||
/* U55 */
|
||||
&cp0_spi1 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&cp0_spi0_pins>;
|
||||
reg = <0x700680 0x50>, /* control */
|
||||
<0x2000000 0x1000000>; /* CS0 */
|
||||
status = "okay";
|
||||
spi-flash@0 {
|
||||
#address-cells = <0x1>;
|
||||
#size-cells = <0x1>;
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0x0>;
|
||||
spi-max-frequency = <40000000>;
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
partition@0 {
|
||||
label = "U-Boot";
|
||||
reg = <0x0 0x1f0000>;
|
||||
};
|
||||
partition@1f0000 {
|
||||
label = "U-Boot ENV Factory";
|
||||
reg = <0x1f0000 0x10000>;
|
||||
};
|
||||
partition@200000 {
|
||||
label = "Reserved";
|
||||
reg = <0x200000 0x1f0000>;
|
||||
};
|
||||
partition@3f0000 {
|
||||
label = "U-Boot ENV";
|
||||
reg = <0x3f0000 0x10000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&cp0_syscon0 {
|
||||
cp0_pinctrl: pinctrl {
|
||||
compatible = "marvell,cp115-standalone-pinctrl";
|
||||
cp0_i2c0_pins: cp0-i2c-pins-0 {
|
||||
marvell,pins = "mpp37", "mpp38";
|
||||
marvell,function = "i2c0";
|
||||
};
|
||||
cp0_i2c1_pins: cp0-i2c-pins-1 {
|
||||
marvell,pins = "mpp35", "mpp36";
|
||||
marvell,function = "i2c1";
|
||||
};
|
||||
cp0_ge1_rgmii_pins: cp0-ge-rgmii-pins-0 {
|
||||
marvell,pins = "mpp0", "mpp1", "mpp2",
|
||||
"mpp3", "mpp4", "mpp5",
|
||||
"mpp6", "mpp7", "mpp8",
|
||||
"mpp9", "mpp10", "mpp11";
|
||||
marvell,function = "ge0";
|
||||
};
|
||||
cp0_ge2_rgmii_pins: cp0-ge-rgmii-pins-1 {
|
||||
marvell,pins = "mpp44", "mpp45", "mpp46",
|
||||
"mpp47", "mpp48", "mpp49",
|
||||
"mpp50", "mpp51", "mpp52",
|
||||
"mpp53", "mpp54", "mpp55";
|
||||
marvell,function = "ge1";
|
||||
};
|
||||
cp0_spi0_pins: cp0-spi-pins-0 {
|
||||
marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
|
||||
marvell,function = "spi1";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
/*
|
||||
* Instantiate the first connected CP115
|
||||
*/
|
||||
|
||||
#define CP11X_NAME cp1
|
||||
#define CP11X_BASE f6000000
|
||||
#define CP11X_PCIEx_MEM_BASE(iface) (0xe2000000 + (iface * 0x1000000))
|
||||
#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
|
||||
#define CP11X_PCIE0_BASE f6600000
|
||||
#define CP11X_PCIE1_BASE f6620000
|
||||
#define CP11X_PCIE2_BASE f6640000
|
||||
|
||||
#include "armada-cp115.dtsi"
|
||||
|
||||
#undef CP11X_NAME
|
||||
#undef CP11X_BASE
|
||||
#undef CP11X_PCIEx_MEM_BASE
|
||||
#undef CP11X_PCIEx_MEM_SIZE
|
||||
#undef CP11X_PCIE0_BASE
|
||||
#undef CP11X_PCIE1_BASE
|
||||
#undef CP11X_PCIE2_BASE
|
||||
|
||||
&cp1_crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cp1_xmdio {
|
||||
status = "okay";
|
||||
cp1_nbaset_phy0: ethernet-phy@3 {
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
reg = <2>;
|
||||
};
|
||||
cp1_nbaset_phy1: ethernet-phy@4 {
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
reg = <0>;
|
||||
};
|
||||
cp1_nbaset_phy2: ethernet-phy@5 {
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
reg = <8>;
|
||||
};
|
||||
};
|
||||
|
||||
&cp1_ethernet {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/* CON50 */
|
||||
&cp1_eth0 {
|
||||
status = "okay";
|
||||
phy-mode = "2500base-x";
|
||||
phys = <&cp1_comphy2 0>;
|
||||
managed = "in-band-status";
|
||||
};
|
||||
|
||||
&cp1_eth1 {
|
||||
status = "okay";
|
||||
phy-mode = "2500base-x";
|
||||
phys = <&cp1_comphy4 1>;
|
||||
managed = "in-band-status";
|
||||
};
|
||||
|
||||
&cp1_eth2 {
|
||||
status = "okay";
|
||||
phy-mode = "2500base-x";
|
||||
phys = <&cp1_comphy5 2>;
|
||||
managed = "in-band-status";
|
||||
};
|
||||
|
||||
&cp1_sata0 {
|
||||
status = "okay";
|
||||
sata-port@1 {
|
||||
status = "okay";
|
||||
phys = <&cp1_comphy0 1>;
|
||||
};
|
||||
};
|
||||
|
||||
&cp1_gpio1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cp1_gpio2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cp1_i2c0 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&cp1_i2c0_pins>;
|
||||
clock-frequency = <100000>;
|
||||
};
|
||||
|
||||
&cp1_syscon0 {
|
||||
cp1_pinctrl: pinctrl {
|
||||
compatible = "marvell,cp115-standalone-pinctrl";
|
||||
cp1_i2c0_pins: cp1-i2c-pins-0 {
|
||||
marvell,pins = "mpp37", "mpp38";
|
||||
marvell,function = "i2c0";
|
||||
};
|
||||
cp1_spi0_pins: cp1-spi-pins-0 {
|
||||
marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
|
||||
marvell,function = "spi1";
|
||||
};
|
||||
cp1_xhci0_vbus_pins: cp1-xhci0-vbus-pins {
|
||||
marvell,pins = "mpp3";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
cp1_sfp_pins: sfp-pins {
|
||||
marvell,pins = "mpp8", "mpp9", "mpp10", "mpp11";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&cp1_usb3_1 {
|
||||
status = "okay";
|
||||
phys = <&cp1_comphy3 1>;
|
||||
phy-names = "usb";
|
||||
};
|
||||
|
|
@ -0,0 +1,481 @@
|
|||
// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
|
||||
/*
|
||||
* Copyright (C) 2019 Marvell International Ltd.
|
||||
*
|
||||
* Device tree for the CN9132-DB board.
|
||||
*/
|
||||
|
||||
#include "cn9130.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
|
||||
/ {
|
||||
model = "iEi Puzzle-M902";
|
||||
compatible = "iei,puzzle-m902",
|
||||
"marvell,armada-ap807-quad", "marvell,armada-ap807";
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
aliases {
|
||||
i2c0 = &cp1_i2c0;
|
||||
i2c1 = &cp0_i2c0;
|
||||
gpio1 = &cp0_gpio1;
|
||||
gpio2 = &cp0_gpio2;
|
||||
gpio3 = &cp1_gpio1;
|
||||
gpio4 = &cp1_gpio2;
|
||||
gpio5 = &cp2_gpio1;
|
||||
gpio6 = &cp2_gpio2;
|
||||
ethernet0 = &cp0_eth0;
|
||||
ethernet1 = &cp0_eth1;
|
||||
ethernet2 = &cp0_eth2;
|
||||
ethernet3 = &cp1_eth0;
|
||||
ethernet4 = &cp1_eth1;
|
||||
ethernet5 = &cp1_eth2;
|
||||
ethernet6 = &cp2_eth0;
|
||||
ethernet7 = &cp2_eth1;
|
||||
ethernet8 = &cp2_eth2;
|
||||
spi1 = &cp0_spi0;
|
||||
spi2 = &cp0_spi1;
|
||||
serial1 = &cp0_uart0;
|
||||
};
|
||||
|
||||
memory@00000000 {
|
||||
device_type = "memory";
|
||||
reg = <0x0 0x0 0x0 0x80000000>;
|
||||
};
|
||||
|
||||
cp2_reg_usb3_vbus0: cp2_usb3_vbus@0 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "cp2-xhci0-vbus";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
enable-active-high;
|
||||
gpio = <&cp2_gpio1 2 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
cp2_usb3_0_phy0: cp2_usb3_phy0 {
|
||||
compatible = "usb-nop-xceiv";
|
||||
vcc-supply = <&cp2_reg_usb3_vbus0>;
|
||||
};
|
||||
|
||||
cp2_reg_usb3_vbus1: cp2_usb3_vbus@1 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "cp2-xhci1-vbus";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
enable-active-high;
|
||||
gpio = <&cp2_gpio1 3 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
cp2_usb3_0_phy1: cp2_usb3_phy1 {
|
||||
compatible = "usb-nop-xceiv";
|
||||
vcc-supply = <&cp2_reg_usb3_vbus1>;
|
||||
};
|
||||
|
||||
cp2_sfp_eth0: sfp-eth0 {
|
||||
compatible = "sff,sfp";
|
||||
i2c-bus = <&cp2_sfpp0_i2c>;
|
||||
los-gpio = <&cp2_module_expander1 11 GPIO_ACTIVE_HIGH>;
|
||||
mod-def0-gpio = <&cp2_module_expander1 10 GPIO_ACTIVE_LOW>;
|
||||
tx-disable-gpio = <&cp2_module_expander1 9 GPIO_ACTIVE_HIGH>;
|
||||
tx-fault-gpio = <&cp2_module_expander1 8 GPIO_ACTIVE_HIGH>;
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cp0_uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/* on-board eMMC - U9 */
|
||||
&ap_sdhci0 {
|
||||
pinctrl-names = "default";
|
||||
bus-width = <8>;
|
||||
status = "okay";
|
||||
mmc-ddr-1_8v;
|
||||
mmc-hs400-1_8v;
|
||||
};
|
||||
|
||||
&cp0_crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cp0_xmdio {
|
||||
status = "okay";
|
||||
cp0_nbaset_phy0: ethernet-phy@0 {
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
reg = <2>;
|
||||
};
|
||||
cp0_nbaset_phy1: ethernet-phy@1 {
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
reg = <0>;
|
||||
};
|
||||
cp0_nbaset_phy2: ethernet-phy@2 {
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
reg = <8>;
|
||||
};
|
||||
};
|
||||
|
||||
&cp0_ethernet {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/* SLM-1521-V2, CON9 */
|
||||
&cp0_eth0 {
|
||||
status = "okay";
|
||||
phy-mode = "10gbase-kr";
|
||||
phys = <&cp0_comphy2 0>;
|
||||
managed = "in-band-status";
|
||||
};
|
||||
|
||||
&cp0_eth1 {
|
||||
status = "okay";
|
||||
phy-mode = "2500base-x";
|
||||
phys = <&cp0_comphy4 1>;
|
||||
managed = "in-band-status";
|
||||
};
|
||||
|
||||
&cp0_eth2 {
|
||||
status = "okay";
|
||||
phy-mode = "2500base-x";
|
||||
phys = <&cp0_comphy1 2>;
|
||||
managed = "in-band-status";
|
||||
};
|
||||
|
||||
&cp0_gpio1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cp0_gpio2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cp0_i2c0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&cp0_i2c0_pins>;
|
||||
status = "okay";
|
||||
clock-frequency = <100000>;
|
||||
rtc@32 {
|
||||
compatible = "epson,rx8130";
|
||||
reg = <0x32>;
|
||||
wakeup-source;
|
||||
};
|
||||
};
|
||||
|
||||
&cp0_i2c1 {
|
||||
clock-frequency = <100000>;
|
||||
};
|
||||
|
||||
/* SLM-1521-V2, CON6 */
|
||||
&cp0_sata0 {
|
||||
status = "okay";
|
||||
sata-port@1 {
|
||||
status = "okay";
|
||||
phys = <&cp0_comphy0 1>;
|
||||
};
|
||||
};
|
||||
|
||||
&cp0_pcie2 {
|
||||
status = "okay";
|
||||
num-lanes = <1>;
|
||||
num-viewport = <8>;
|
||||
phys = <&cp0_comphy5 2>;
|
||||
};
|
||||
|
||||
/* U55 */
|
||||
&cp0_spi1 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&cp0_spi0_pins>;
|
||||
reg = <0x700680 0x50>, /* control */
|
||||
<0x2000000 0x1000000>; /* CS0 */
|
||||
status = "okay";
|
||||
spi-flash@0 {
|
||||
#address-cells = <0x1>;
|
||||
#size-cells = <0x1>;
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0x0>;
|
||||
spi-max-frequency = <40000000>;
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
partition@0 {
|
||||
label = "U-Boot";
|
||||
reg = <0x0 0x1f0000>;
|
||||
};
|
||||
partition@1f0000 {
|
||||
label = "U-Boot ENV Factory";
|
||||
reg = <0x1f0000 0x10000>;
|
||||
};
|
||||
partition@200000 {
|
||||
label = "Reserved";
|
||||
reg = <0x200000 0x1f0000>;
|
||||
};
|
||||
partition@3f0000 {
|
||||
label = "U-Boot ENV";
|
||||
reg = <0x3f0000 0x10000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&cp0_syscon0 {
|
||||
cp0_pinctrl: pinctrl {
|
||||
compatible = "marvell,cp115-standalone-pinctrl";
|
||||
cp0_i2c0_pins: cp0-i2c-pins-0 {
|
||||
marvell,pins = "mpp37", "mpp38";
|
||||
marvell,function = "i2c0";
|
||||
};
|
||||
cp0_i2c1_pins: cp0-i2c-pins-1 {
|
||||
marvell,pins = "mpp35", "mpp36";
|
||||
marvell,function = "i2c1";
|
||||
};
|
||||
cp0_ge1_rgmii_pins: cp0-ge-rgmii-pins-0 {
|
||||
marvell,pins = "mpp0", "mpp1", "mpp2",
|
||||
"mpp3", "mpp4", "mpp5",
|
||||
"mpp6", "mpp7", "mpp8",
|
||||
"mpp9", "mpp10", "mpp11";
|
||||
marvell,function = "ge0";
|
||||
};
|
||||
cp0_ge2_rgmii_pins: cp0-ge-rgmii-pins-1 {
|
||||
marvell,pins = "mpp44", "mpp45", "mpp46",
|
||||
"mpp47", "mpp48", "mpp49",
|
||||
"mpp50", "mpp51", "mpp52",
|
||||
"mpp53", "mpp54", "mpp55";
|
||||
marvell,function = "ge1";
|
||||
};
|
||||
cp0_spi0_pins: cp0-spi-pins-0 {
|
||||
marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
|
||||
marvell,function = "spi1";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&cp0_usb3_1 {
|
||||
status = "okay";
|
||||
phys = <&cp0_comphy3 1>;
|
||||
phy-names = "usb";
|
||||
};
|
||||
|
||||
/*
|
||||
* Instantiate the first connected CP115
|
||||
*/
|
||||
|
||||
#define CP11X_NAME cp1
|
||||
#define CP11X_BASE f4000000
|
||||
#define CP11X_PCIEx_MEM_BASE(iface) (0xe2000000 + (iface * 0x1000000))
|
||||
#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
|
||||
#define CP11X_PCIE0_BASE f4600000
|
||||
#define CP11X_PCIE1_BASE f4620000
|
||||
#define CP11X_PCIE2_BASE f4640000
|
||||
|
||||
#include "armada-cp115.dtsi"
|
||||
|
||||
#undef CP11X_NAME
|
||||
#undef CP11X_BASE
|
||||
#undef CP11X_PCIEx_MEM_BASE
|
||||
#undef CP11X_PCIEx_MEM_SIZE
|
||||
#undef CP11X_PCIE0_BASE
|
||||
#undef CP11X_PCIE1_BASE
|
||||
#undef CP11X_PCIE2_BASE
|
||||
|
||||
&cp1_crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cp1_xmdio {
|
||||
status = "okay";
|
||||
cp1_nbaset_phy0: ethernet-phy@3 {
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
reg = <2>;
|
||||
};
|
||||
cp1_nbaset_phy1: ethernet-phy@4 {
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
reg = <0>;
|
||||
};
|
||||
cp1_nbaset_phy2: ethernet-phy@5 {
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
reg = <8>;
|
||||
};
|
||||
};
|
||||
|
||||
&cp1_ethernet {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/* CON50 */
|
||||
&cp1_eth0 {
|
||||
status = "okay";
|
||||
phy-mode = "10gbase-kr";
|
||||
phys = <&cp1_comphy2 0>;
|
||||
managed = "in-band-status";
|
||||
};
|
||||
|
||||
&cp1_eth1 {
|
||||
status = "okay";
|
||||
phy-mode = "2500base-x";
|
||||
phys = <&cp1_comphy4 1>;
|
||||
managed = "in-band-status";
|
||||
};
|
||||
|
||||
&cp1_eth2 {
|
||||
status = "okay";
|
||||
phy-mode = "2500base-x";
|
||||
phys = <&cp1_comphy1 2>;
|
||||
managed = "in-band-status";
|
||||
};
|
||||
|
||||
&cp1_gpio1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cp1_gpio2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cp1_i2c0 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&cp1_i2c0_pins>;
|
||||
clock-frequency = <100000>;
|
||||
};
|
||||
|
||||
&cp1_syscon0 {
|
||||
cp1_pinctrl: pinctrl {
|
||||
compatible = "marvell,cp115-standalone-pinctrl";
|
||||
cp1_i2c0_pins: cp1-i2c-pins-0 {
|
||||
marvell,pins = "mpp37", "mpp38";
|
||||
marvell,function = "i2c0";
|
||||
};
|
||||
cp1_spi0_pins: cp1-spi-pins-0 {
|
||||
marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
|
||||
marvell,function = "spi1";
|
||||
};
|
||||
cp1_xhci0_vbus_pins: cp1-xhci0-vbus-pins {
|
||||
marvell,pins = "mpp3";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
/*
|
||||
* Instantiate the second connected CP115
|
||||
*/
|
||||
|
||||
#define CP11X_NAME cp2
|
||||
#define CP11X_BASE f6000000
|
||||
#define CP11X_PCIEx_MEM_BASE(iface) (0xe5000000 + (iface * 0x1000000))
|
||||
#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
|
||||
#define CP11X_PCIE0_BASE f6600000
|
||||
#define CP11X_PCIE1_BASE f6620000
|
||||
#define CP11X_PCIE2_BASE f6640000
|
||||
|
||||
#include "armada-cp115.dtsi"
|
||||
|
||||
#undef CP11X_NAME
|
||||
#undef CP11X_BASE
|
||||
#undef CP11X_PCIEx_MEM_BASE
|
||||
#undef CP11X_PCIEx_MEM_SIZE
|
||||
#undef CP11X_PCIE0_BASE
|
||||
#undef CP11X_PCIE1_BASE
|
||||
#undef CP11X_PCIE2_BASE
|
||||
|
||||
&cp2_crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cp2_ethernet {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cp2_xmdio {
|
||||
status = "okay";
|
||||
cp2_nbaset_phy0: ethernet-phy@6 {
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
reg = <2>;
|
||||
};
|
||||
cp2_nbaset_phy1: ethernet-phy@7 {
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
reg = <0>;
|
||||
};
|
||||
cp2_nbaset_phy2: ethernet-phy@8 {
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
reg = <8>;
|
||||
};
|
||||
};
|
||||
|
||||
/* SLM-1521-V2, CON9 */
|
||||
&cp2_eth0 {
|
||||
status = "okay";
|
||||
phy-mode = "10gbase-kr";
|
||||
phys = <&cp2_comphy2 0>;
|
||||
managed = "in-band-status";
|
||||
};
|
||||
|
||||
&cp2_eth1 {
|
||||
status = "okay";
|
||||
phy-mode = "2500base-x";
|
||||
phys = <&cp2_comphy4 1>;
|
||||
managed = "in-band-status";
|
||||
};
|
||||
|
||||
&cp2_eth2 {
|
||||
status = "okay";
|
||||
phy-mode = "2500base-x";
|
||||
phys = <&cp2_comphy1 2>;
|
||||
managed = "in-band-status";
|
||||
};
|
||||
|
||||
&cp2_gpio1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cp2_gpio2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cp2_i2c0 {
|
||||
clock-frequency = <100000>;
|
||||
/* SLM-1521-V2 - U3 */
|
||||
i2c-mux@72 {
|
||||
compatible = "nxp,pca9544";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0x72>;
|
||||
cp2_sfpp0_i2c: i2c@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0>;
|
||||
};
|
||||
|
||||
i2c@1 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <1>;
|
||||
/* U12 */
|
||||
cp2_module_expander1: pca9555@21 {
|
||||
compatible = "nxp,pca9555";
|
||||
pinctrl-names = "default";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
reg = <0x21>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&cp2_syscon0 {
|
||||
cp2_pinctrl: pinctrl {
|
||||
compatible = "marvell,cp115-standalone-pinctrl";
|
||||
cp2_i2c0_pins: cp2-i2c-pins-0 {
|
||||
marvell,pins = "mpp37", "mpp38";
|
||||
marvell,function = "i2c0";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
|
@ -43,3 +43,21 @@ define Device/marvell_macchiatobin-singleshot
|
|||
SUPPORTED_DEVICES := marvell,armada8040-mcbin-singleshot
|
||||
endef
|
||||
TARGET_DEVICES += marvell_macchiatobin-singleshot
|
||||
|
||||
define Device/iei_puzzle-m901
|
||||
$(call Device/Default-arm64)
|
||||
DEVICE_VENDOR := iEi
|
||||
DEVICE_MODEL := Puzzle-M901
|
||||
SOC := cn9131
|
||||
IMAGE/sdcard.img.gz := boot-img-ext4 | sdcard-img-ext4 | gzip | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += iei_puzzle-m901
|
||||
|
||||
define Device/iei_puzzle-m902
|
||||
$(call Device/Default-arm64)
|
||||
DEVICE_VENDOR := iEi
|
||||
DEVICE_MODEL := Puzzle-M902
|
||||
SOC := cn9132
|
||||
IMAGE/sdcard.img.gz := boot-img-ext4 | sdcard-img-ext4 | gzip | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += iei_puzzle-m902
|
||||
|
|
|
|||
Loading…
Reference in New Issue