mirror/openwrt
1
0
Fork 0
mirror of https://git.openwrt.org/openwrt/openwrt.git synced 2024-06-18 13:13:55 +02:00
Code Releases Activity

bcm63xx: add support for Technicolor TG582n Telecom Italia branded

Browse Source 
Technicolor TG582n Telecom Italia branded a.k.a.
Telecom Italia ADSL2+ Wi-Fi N (AGTWI)
has the same PCB as the unbranded Technicolor TG582n with LEDs
connected to different GPIO PINs in active low configuration and
different LED names. It has a PCB similar to the OpenWrt's ADB P.DG A4001N1 one.

Hardware:
* Board ID: DANT-V
* SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350
* RAM DDR2: 64 Mbyte - EtronTech EM68B16CWQD-25H
* Serial flash: 16 Mbyte - Spansion FL 128SAIF00
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43227 Wireless Network Adapter (rev 30)
* LEDs: 2x Power, 1x ADSL, 2x Internet, 2x Wi-Fi, 2x Service, 4x ethernet
* Buttons: 1x Reset, 1x WPS (named WiFi/LED)
* UART: 1x TTL 115200n8, VCC GND TX RX, on J3 connector (short R62 and R63)

Installation via CFE:
* Stock CFE has to be overwritten with a generic 6328 one that can upload
  .bin images with no signature check (cfe6328_configured.bin)
* Connect a serial port to the board
* Stop the CFE boot process after power on by pressing enter
* Set static IP 192.168.2.10 and subnet mask 255.255.255.0
* Navigate to http://192.168.2.50/
* Upload the OpenWrt image file

PCB:   |GPIO:   |TG582n:          |AGTWI:

LED2R  |488(08) |red    Power     |red   Power
LED2G  |484(04) |green  Power     |green Power

LED10R |486(06) |                 |missing R85 end LED
LED13G |485(05) |green  Ethernet  |green ADSL

LED11R |494(14) |                 |red   Internet
LED14G |491(11) |green  Broadband |green Internet

LED5R  |487(07) |red    Internet  |red   Wi-Fi
LED5G  |481(01) |green  Internet  |green Wi-Fi

LED12R |498(18) |                 |red   Service
LED12G |499(19) |                 |green Service

LED6R  |482(02) |red    Wi-Fi     |missing R108 end LED
LED6G  |483(03) |green  Wi-Fi     |missing R107 end LED

LED7R  |490(10) |red    WPS       |missing R91 end LED
LED7G  |489(09) |green  WPS       |missing R92 end LED

LED4   |508(28) |ethernet port 4  |ethernet port 4
LED3   |507(27) |ethernet port 3  |ethernet port 3

LED9   |506(26) |ethernet port 2  |ethernet port 2
LED8   |505(25) |ethernet port 1  |ethernet port 1

SW3    |503(23) |key Reset        |key Reset

SW5    |504(24) |key WPS          |key Wi-Fi/LED

SW4    |495(15) |key Wi-Fi        |missing R127 end key

SW6    |493(13) |                 |missing R171 end key

SW1    |492(12) |                 |missing R1 end key

Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
[DT fixes, base-files fixes and device variant]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This commit is contained in:
Daniele Castro 2020-09-08 17:16:06 +02:00 committed by Álvaro Fernández Rojas
parent 2f75348923
commit c143fbc5f1
14 changed files with 245 additions and 26 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

5
target/linux/bcm63xx/base-files/etc/board.d/01_leds
View File

@ -94,6 +94,11 @@ sercomm,h500-s-lowi|\
sercomm,h500-s-vfes)
ucidef_set_led_netdev "wan" "WAN" "green:internet" "eth0.2"
;;
technicolor,tg582n-telecom-italia)
ucidef_set_led_netdev "wlan0" "WIFI" "green:wifi" "wlan0"
ucidef_set_led_usbdev "usb1" "USB1" "green:service" "1-1"
ucidef_set_led_usbdev "usb2" "USB2" "red:service" "2-1"
;;
telsey,cpva502plus)
ucidef_set_led_netdev "lan" "LAN" "amber:link" "eth0"
;;

1
target/linux/bcm63xx/base-files/etc/board.d/02_network
View File

@ -39,6 +39,7 @@ huawei,echolife-hg655b|\
nucom,r5010un-v2|\
sagem,fast-2504n|\
sagem,fast-2704-v2|\
technicolor,tg582n-telecom-italia|\
zyxel,p870hw-51a-v2)
ucidef_add_switch "switch0" \
"0:lan:1" "1:lan:2" "2:lan:3" "3:lan:4" "8t@eth0"

1
target/linux/bcm63xx/base-files/etc/uci-defaults/09_fix_crc
View File

@ -34,6 +34,7 @@ case "$(board_name)" in
nucom,r5010un-v2|\
observa,vh4032n|\
t-com,speedport-w-303v|\
technicolor,tg582n-telecom-italia|\
telsey,cpva502plus|\
telsey,cpva642|\
telsey,magic|\

153
target/linux/bcm63xx/dts/bcm6328-technicolor-tg582n-telecom-italia.dts Normal file
View File

@ -0,0 +1,153 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "bcm6328.dtsi"
#include <dt-bindings/input/input.h>
/ {
model = "Technicolor TG582n Telecom Italia";
compatible = "technicolor,tg582n-telecom-italia", "brcm,bcm6328";
aliases {
led-boot = &led_power_green;
led-failsafe = &led_power_green;
led-running = &led_power_green;
led-upgrade = &led_power_green;
};
chosen {
bootargs = "rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200";
stdout-path = "serial0:115200n8";
};
keys {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <20>;
reset {
label = "reset";
gpios = <&pinctrl 23 1>;
linux,code = <KEY_RESTART>;
debounce-interval = <60>;
};
wps {
label = "wps";
gpios = <&pinctrl 24 1>;
linux,code = <KEY_WPS_BUTTON>;
debounce-interval = <60>;
};
};
};
&leds {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_leds>;
led@1 {
reg = <1>;
active-low;
label = "green:wifi";
};
led_power_green: led@4 {
reg = <4>;
active-low;
label = "green:power";
default-state = "on";
};
led@5 {
reg = <5>;
active-low;
label = "green:adsl";
};
led@7 {
reg = <7>;
active-low;
label = "red:wifi";
};
led@8 {
reg = <8>;
active-low;
label = "red:power";
};
led@11 {
reg = <11>;
active-low;
label = "green:internet";
};
led@14 {
reg = <14>;
active-low;
label = "red:internet";
};
led@18 {
reg = <18>;
active-low;
label = "red:service";
};
led@19 {
reg = <19>;
active-low;
label = "green:service";
};
};
&hsspi {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
spi-max-frequency = <16666667>;
spi-tx-bus-width = <2>;
spi-rx-bus-width = <2>;
reg = <0>;
#address-cells = <1>;
#size-cells = <1>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
reg = <0x000000 0x010000>;
label = "cfe";
read-only;
};
partition@10000 {
reg = <0x010000 0xff0000>;
label = "linux";
compatible = "brcm,bcm963xx-imagetag";
};
};
};
};
&pinctrl {
pinctrl_leds: leds {
function = "led";
pins = "gpio1", "gpio4",
"gpio5", "gpio7",
"gpio8", "gpio11",
"gpio14", "gpio18",
"gpio19";
};
};
&uart0 {
status = "okay";
};

14
target/linux/bcm63xx/image/bcm63xx.mk
View File

@ -1098,6 +1098,20 @@ define Device/t-com_speedport-w-500v
endef
TARGET_DEVICES += t-com_speedport-w-500v
### Technicolor ###
define Device/technicolor_tg582n-telecom-italia
$(Device/bcm63xx)
DEVICE_VENDOR := Technicolor
DEVICE_MODEL := TG582n
DEVICE_VARIANT := Telecom Italia
IMAGES += sysupgrade.bin
CFE_BOARD_ID := DANT-V
CHIP_ID := 6328
FLASH_MB := 16
DEVICE_PACKAGES := $(USB2_PACKAGES) $(B43_PACKAGES)
endef
TARGET_DEVICES += technicolor_tg582n-telecom-italia
### Tecom ###
define Device/tecom_gw6000
$(Device/bcm63xx-legacy)

51
target/linux/bcm63xx/patches-5.4/512-board_bcm6328.patch
View File

@ -1,6 +1,6 @@
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
@@ -348,6 +348,525 @@ static struct board_info __initdata boar
@@ -348,6 +348,568 @@ static struct board_info __initdata boar
},
},
};
@ -522,11 +522,54 @@
+ .pci_bus = 1,
+ .pci_dev = 0,
+ },
+};
+
+static struct board_info __initdata board_TG582N_TELECOM_ITALIA = {
+ .name = "DANT-V",
+ .expected_cpu_id = 0x6328,
+
+ .has_pci = 1,
+ .has_ohci0 = 1,
+ .has_ehci0 = 1,
+ .num_usbh_ports = 1,
+
+ .has_enetsw = 1,
+ .enetsw = {
+ .used_ports = {
+ [0] = {
+ .used = 1,
+ .phy_id = 1,
+ .name = "Port 1",
+ },
+ [1] = {
+ .used = 1,
+ .phy_id = 2,
+ .name = "Port 2",
+ },
+ [2] = {
+ .used = 1,
+ .phy_id = 3,
+ .name = "Port 3",
+ },
+ [3] = {
+ .used = 1,
+ .phy_id = 4,
+ .name = "Port 4",
+ },
+ },
+ },
+
+ .use_fallback_sprom = 1,
+ .fallback_sprom = {
+ .type = SPROM_BCM43225,
+ .pci_bus = 1,
+ .pci_dev = 0,
+ },
+};
#endif /* CONFIG_BCM63XX_CPU_6328 */
/*
@@ -703,6 +1222,17 @@ static const struct board_info __initcon
@@ -703,6 +1265,18 @@ static const struct board_info __initcon
#endif /* CONFIG_BCM63XX_CPU_6318 */
#ifdef CONFIG_BCM63XX_CPU_6328
&board_96328avng,
@ -540,11 +583,12 @@
+ &board_FAST2704V2,
+ &board_PDG_A4001N_A_000_1A1_AX,
+ &board_PDG_A4101N_A_000_1A1_AE,
+ &board_TG582N_TELECOM_ITALIA,
+ &board_R5010UNV2,
#endif /* CONFIG_BCM63XX_CPU_6328 */
#ifdef CONFIG_BCM63XX_CPU_6338
&board_96338gw,
@@ -742,7 +1272,20 @@ static struct of_device_id const bcm963x
@@ -742,7 +1316,21 @@ static struct of_device_id const bcm963x
{ .compatible = "sagem,fast-2704n", .data = &board_FAST2704N, },
#endif /* CONFIG_BCM63XX_CPU_6318 */
#ifdef CONFIG_BCM63XX_CPU_6328
@ -562,6 +606,7 @@
+ { .compatible = "sagem,fast-2704-v2", .data = &board_FAST2704V2, },
+ { .compatible = "sercomm,ad1018", .data = &board_AD1018, },
+ { .compatible = "sercomm,ad1018-nor", .data = &board_AD1018, },
+ { .compatible = "technicolor,tg582n-telecom-italia", .data = &board_TG582N_TELECOM_ITALIA, },
#endif /* CONFIG_BCM63XX_CPU_6328 */
#ifdef CONFIG_BCM63XX_CPU_6338
{ .compatible = "brcm,bcm96338gw", .data = &board_96338gw, },

6
target/linux/bcm63xx/patches-5.4/513-board-bcm6338.patch
View File

@ -1,6 +1,6 @@
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
@@ -900,6 +900,32 @@ static struct board_info __initdata boar
@@ -943,6 +943,32 @@ static struct board_info __initdata boar
.force_duplex_full = 1,
},
};
@ -33,7 +33,7 @@
#endif /* CONFIG_BCM63XX_CPU_6338 */
/*
@@ -1237,6 +1263,8 @@ static const struct board_info __initcon
@@ -1281,6 +1307,8 @@ static const struct board_info __initcon
#ifdef CONFIG_BCM63XX_CPU_6338
&board_96338gw,
&board_96338w,
@ -42,7 +42,7 @@
#endif /* CONFIG_BCM63XX_CPU_6338 */
#ifdef CONFIG_BCM63XX_CPU_6345
&board_96345gw2,
@@ -1290,6 +1318,8 @@ static struct of_device_id const bcm963x
@@ -1335,6 +1363,8 @@ static struct of_device_id const bcm963x
#ifdef CONFIG_BCM63XX_CPU_6338
{ .compatible = "brcm,bcm96338gw", .data = &board_96338gw, },
{ .compatible = "brcm,bcm96338w", .data = &board_96338w, },

6
target/linux/bcm63xx/patches-5.4/514-board_bcm6345.patch
View File

@ -1,6 +1,6 @@
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
@@ -936,6 +936,19 @@ static struct board_info __initdata boar
@@ -979,6 +979,19 @@ static struct board_info __initdata boar
.name = "96345GW2",
.expected_cpu_id = 0x6345,
};
@ -20,7 +20,7 @@
#endif /* CONFIG_BCM63XX_CPU_6345 */
/*
@@ -1268,6 +1281,7 @@ static const struct board_info __initcon
@@ -1312,6 +1325,7 @@ static const struct board_info __initcon
#endif /* CONFIG_BCM63XX_CPU_6338 */
#ifdef CONFIG_BCM63XX_CPU_6345
&board_96345gw2,
@ -28,7 +28,7 @@
#endif /* CONFIG_BCM63XX_CPU_6345 */
#ifdef CONFIG_BCM63XX_CPU_6348
&board_96348r,
@@ -1323,6 +1337,8 @@ static struct of_device_id const bcm963x
@@ -1368,6 +1382,8 @@ static struct of_device_id const bcm963x
#endif /* CONFIG_BCM63XX_CPU_6338 */
#ifdef CONFIG_BCM63XX_CPU_6345
{ .compatible = "brcm,bcm96345gw2", .data = &board_96345gw2, },

6
target/linux/bcm63xx/patches-5.4/515-board-bcm6348.patch
View File

@ -1,6 +1,6 @@
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
@@ -1135,6 +1135,275 @@ static struct board_info __initdata boar
@@ -1178,6 +1178,275 @@ static struct board_info __initdata boar
.has_ohci0 = 1,
};
@ -276,7 +276,7 @@
#endif /* CONFIG_BCM63XX_CPU_6348 */
/*
@@ -1292,6 +1561,19 @@ static const struct board_info __initcon
@@ -1336,6 +1605,19 @@ static const struct board_info __initcon
&board_DV201AMR,
&board_96348gw_a,
&board_rta1025w_16,
@ -296,7 +296,7 @@
#endif /* CONFIG_BCM63XX_CPU_6348 */
#ifdef CONFIG_BCM63XX_CPU_6358
&board_96358vw,
@@ -1341,15 +1623,29 @@ static struct of_device_id const bcm963x
@@ -1386,15 +1668,29 @@ static struct of_device_id const bcm963x
{ .compatible = "dynalink,rta770w", .data = &board_rta770w, },
#endif /* CONFIG_BCM63XX_CPU_6345 */
#ifdef CONFIG_BCM63XX_CPU_6348

8
target/linux/bcm63xx/patches-5.4/516-board-bcm6358.patch
View File

@ -8,7 +8,7 @@
#include <asm/addrspace.h>
#include <bcm63xx_board.h>
#include <bcm63xx_cpu.h>
@@ -1488,6 +1489,88 @@ static struct board_info __initdata boar
@@ -1531,6 +1532,88 @@ static struct board_info __initdata boar
.has_ehci0 = 1,
};
@ -97,7 +97,7 @@
static struct board_info __initdata board_DWVS0 = {
.name = "DWV-S0",
.expected_cpu_id = 0x6358,
@@ -1512,6 +1595,238 @@ static struct board_info __initdata boar
@@ -1555,6 +1638,238 @@ static struct board_info __initdata boar
.has_ohci0 = 1,
.has_ehci0 = 1,
};
@ -336,7 +336,7 @@
#endif /* CONFIG_BCM63XX_CPU_6358 */
/*
@@ -1579,7 +1894,20 @@ static const struct board_info __initcon
@@ -1623,7 +1938,20 @@ static const struct board_info __initcon
&board_96358vw,
&board_96358vw2,
&board_AGPFS0,
@ -357,7 +357,7 @@
#endif /* CONFIG_BCM63XX_CPU_6358 */
};
@@ -1653,11 +1981,24 @@ static struct of_device_id const bcm963x
@@ -1698,11 +2026,24 @@ static struct of_device_id const bcm963x
{ .compatible = "alcatel,rg100a", .data = &board_96358vw2, },
{ .compatible = "brcm,bcm96358vw", .data = &board_96358vw, },
{ .compatible = "brcm,bcm96358vw2", .data = &board_96358vw2, },

6
target/linux/bcm63xx/patches-5.4/517-board_bcm6362.patch
View File

@ -1,6 +1,6 @@
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
@@ -1829,6 +1829,117 @@ static struct board_info __initdata boar
@@ -1872,6 +1872,117 @@ static struct board_info __initdata boar
};
#endif /* CONFIG_BCM63XX_CPU_6358 */
@ -118,7 +118,7 @@
/*
* all boards
*/
@@ -1909,6 +2020,12 @@ static const struct board_info __initcon
@@ -1953,6 +2064,12 @@ static const struct board_info __initcon
&board_nb4_fxc_r1,
&board_spw303v,
#endif /* CONFIG_BCM63XX_CPU_6358 */
@ -131,7 +131,7 @@
};
static struct of_device_id const bcm963xx_boards_dt[] = {
@@ -2001,6 +2118,10 @@ static struct of_device_id const bcm963x
@@ -2046,6 +2163,10 @@ static struct of_device_id const bcm963x
{ .compatible = "telsey,cpva642", .data = &board_CPVA642, },
#endif /* CONFIG_BCM63XX_CPU_6358 */
#ifdef CONFIG_BCM63XX_CPU_6362

6
target/linux/bcm63xx/patches-5.4/518-board_bcm6368.patch
View File

@ -9,7 +9,7 @@
#include <asm/addrspace.h>
#include <bcm63xx_board.h>
#include <bcm63xx_cpu.h>
@@ -1941,6 +1943,648 @@ static struct board_info __initdata boar
@@ -1984,6 +1986,648 @@ static struct board_info __initdata boar
#endif /* CONFIG_BCM63XX_CPU_6362 */
/*
@ -658,7 +658,7 @@
* all boards
*/
static const struct board_info __initconst *bcm963xx_boards[] = {
@@ -2026,6 +2670,22 @@ static const struct board_info __initcon
@@ -2070,6 +2714,22 @@ static const struct board_info __initcon
&board_hg253s_v2,
&board_nb6,
#endif /* CONFIG_BCM63XX_CPU_6362 */
@ -681,7 +681,7 @@
};
static struct of_device_id const bcm963xx_boards_dt[] = {
@@ -2124,6 +2784,20 @@ static struct of_device_id const bcm963x
@@ -2169,6 +2829,20 @@ static struct of_device_id const bcm963x
{ .compatible = "sfr,neufbox-6-sercomm-r0", .data = &board_nb6, },
#endif /* CONFIG_BCM63XX_CPU_6362 */
#ifdef CONFIG_BCM63XX_CPU_6368

6
target/linux/bcm63xx/patches-5.4/519-board_bcm63268.patch
View File

@ -1,6 +1,6 @@
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
@@ -2585,6 +2585,273 @@ static struct board_info __initdata boar
@@ -2628,6 +2628,273 @@ static struct board_info __initdata boar
#endif /* CONFIG_BCM63XX_CPU_6368 */
/*
@ -274,7 +274,7 @@
* all boards
*/
static const struct board_info __initconst *bcm963xx_boards[] = {
@@ -2686,6 +2953,15 @@ static const struct board_info __initcon
@@ -2730,6 +2997,15 @@ static const struct board_info __initcon
&board_VR3026e,
&board_WAP5813n,
#endif /* CONFIG_BCM63XX_CPU_6368 */
@ -290,7 +290,7 @@
};
static struct of_device_id const bcm963xx_boards_dt[] = {
@@ -2800,6 +3076,14 @@ static struct of_device_id const bcm963x
@@ -2845,6 +3121,14 @@ static struct of_device_id const bcm963x
{ .compatible = "zyxel,p870hw-51a-v2", .data = &board_P870HW51A_V2, },
#endif /* CONFIG_BCM63XX_CPU_6368 */
#ifdef CONFIG_BCM63XX_CPU_63268

2
target/linux/bcm63xx/patches-5.4/531-board_bcm6348-bt-voyager-2500v-bb.patch
View File

@ -1,6 +1,6 @@
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
@@ -3112,6 +3112,22 @@ void __init board_bcm963xx_init(void)
@@ -3157,6 +3157,22 @@ void __init board_bcm963xx_init(void)
val &= MPI_CSBASE_BASE_MASK;
}
boot_addr = (u8 *)KSEG1ADDR(val);