mirror
/
openwrt
mirror of https://git.openwrt.org/openwrt/openwrt.git
1
0
Fork 0
Code Releases Activity

ipq40xx: add support for GL.iNet GL-AP1300 

Specifications:
SOC:        Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:        256 MiB
FLASH1:     4 MiB NOR
FLASH2:     128 MiB NAND
ETH:        Qualcomm QCA8075
WLAN1:      Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2:      Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT:      Reset
LED:        Power, Internet
UART1:      On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
OTHER:      On board with BLE module - by cp210x USB serial chip
            On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed

Install via uboot tftp or uboot web failsafe.

By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi
(IPQ40xx) # run lf

By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1

Afterwards upgrade can use sysupgrade image.

Signed-off-by: Dongming Han <handongming@gl-inet.com>
This commit is contained in:
Dongming Han 2020-07-22 15:12:17 +08:00 committed by Petr Štetiar
parent 3bb1618573
commit b9389186b0
9 changed files with 293 additions and 1 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

1
package/boot/uboot-envtools/files/ipq40xx
View File

@ -34,6 +34,7 @@ case "$board" in
alfa-network,ap120c-ac |\
devolo,magic-2-wifi-next |\
edgecore,ecw5211 |\
glinet,gl-ap1300 |\
glinet,gl-b1300 |\
luma,wrtq-329acn |\
openmesh,a42 |\

2
package/firmware/ipq-wifi/Makefile
View File

@ -38,6 +38,7 @@ ALLWIFIBOARDS:= \
engenius_emd1 \
engenius_emr3500 \
ezviz_cs-w3-wd1200g-eup \
glinet_gl-ap1300 \
glinet_gl-s1300 \
linksys_ea8300 \
linksys_mr8300-v0 \
@ -120,6 +121,7 @@ $(eval $(call generate-ipq-wifi-package,engenius_eap2200,EnGenius EAP2200))
$(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1))
$(eval $(call generate-ipq-wifi-package,engenius_emr3500,EnGenius EMR3500))
$(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP))
$(eval $(call generate-ipq-wifi-package,glinet_gl-ap1300,GL.iNet GL-AP1300))
$(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300))
$(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
$(eval $(call generate-ipq-wifi-package,linksys_mr8300-v0,Linksys MR8300))

BIN
package/firmware/ipq-wifi/board-glinet_gl-ap1300.qca4019 Normal file
View File

Binary file not shown.

1
target/linux/ipq40xx/base-files/etc/board.d/02_network
View File

@ -92,6 +92,7 @@ ipq40xx_setup_interfaces()
ucidef_add_switch "switch0" \
"0u@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "0u@eth1" "5:wan"
;;
glinet,gl-ap1300 |\
glinet,gl-b1300 |\
glinet,gl-s1300)
ucidef_set_interfaces_lan_wan "eth0" "eth1"

2
target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
View File

@ -55,6 +55,7 @@ case "$FIRMWARE" in
alfa-network,ap120c-ac |\
cilab,meshpoint-one |\
ezviz,cs-w3-wd1200g-eup |\
glinet,gl-ap1300 |\
glinet,gl-b1300 |\
glinet,gl-s1300 |\
linksys,ea6350v3 |\
@ -158,6 +159,7 @@ case "$FIRMWARE" in
alfa-network,ap120c-ac |\
cilab,meshpoint-one |\
ezviz,cs-w3-wd1200g-eup |\
glinet,gl-ap1300 |\
glinet,gl-b1300 |\
glinet,gl-s1300 |\
linksys,ea6350v3 |\

1
target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
View File

@ -69,6 +69,7 @@ platform_do_upgrade() {
edgecore,ecw5211 |\
edgecore,oap100 |\
engenius,eap2200 |\
glinet,gl-ap1300 |\
luma,wrtq-329acn |\
mobipromo,cm520-79f |\
qxwlan,e2600ac-c2)

269
target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-gl-ap1300.dts Normal file
View File

@ -0,0 +1,269 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "qcom-ipq4019.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/soc/qcom,tcsr.h>
/ {
model = "GL.iNet GL-AP1300";
compatible = "glinet,gl-ap1300";
aliases {
led-boot = &led_power;
led-failsafe = &led_power;
led-running = &led_power;
led-upgrade = &led_power;
};
memory {
device_type = "memory";
reg = <0x80000000 0x10000000>;
};
chosen {
bootargs-append = " ubi.mtd=ubi root=/dev/ubiblock0_1 clk_ignore_unused";
};
soc {
rng@22000 {
status = "okay";
};
mdio@90000 {
status = "okay";
};
ess-psgmii@98000 {
status = "okay";
};
tcsr@1949000 {
compatible = "qcom,tcsr";
reg = <0x1949000 0x100>;
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
};
tcsr@194b000 {
/* select hostmode */
compatible = "qcom,tcsr";
reg = <0x194b000 0x100>;
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
status = "okay";
};
ess_tcsr@1953000 {
compatible = "qcom,tcsr";
reg = <0x1953000 0x1000>;
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
};
tcsr@1957000 {
compatible = "qcom,tcsr";
reg = <0x1957000 0x100>;
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
};
usb2@60f8800 {
status = "okay";
};
usb3@8af8800 {
status = "okay";
};
crypto@8e3a000 {
status = "okay";
};
watchdog@b017000 {
status = "okay";
};
ess-switch@c000000 {
status = "okay";
switch_lan_bmp = <0x18>;
switch_wan_bmp = <0x20>;
};
edma@c080000 {
status = "okay";
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
leds {
compatible = "gpio-leds";
led_power: power {
label = "green:power";
gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
wan {
label = "green:wan";
gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
};
};
};
&blsp_dma {
status = "okay";
};
&cryptobam {
status = "okay";
};
&blsp1_spi1 {
status = "okay";
pinctrl-0 = <&spi0_pins>;
pinctrl-names = "default";
cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 5 GPIO_ACTIVE_HIGH>;
flash@0 {
status = "okay";
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <24000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "SBL1";
reg = <0x00000000 0x00040000>;
read-only;
};
partition@40000 {
label = "MIBIB";
reg = <0x00040000 0x00020000>;
read-only;
};
partition@60000 {
label = "QSEE";
reg = <0x00060000 0x00060000>;
read-only;
};
partition@c0000 {
label = "CDT";
reg = <0x000c0000 0x00010000>;
read-only;
};
partition@d0000 {
label = "DDRPARAMS";
reg = <0x000d0000 0x00010000>;
read-only;
};
partition@e0000 {
label = "APPSBLENV"; /* uboot env*/
reg = <0x000e0000 0x00010000>;
};
partition@f0000 {
label = "APPSBL"; /* uboot */
reg = <0x000f0000 0x00080000>;
read-only;
};
partition@170000 {
label = "ART";
reg = <0x00170000 0x00010000>;
read-only;
};
};
};
spi-nand@1 {
status = "okay";
compatible = "spi-nand";
reg = <1>;
spi-max-frequency = <24000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "ubi";
reg = <0x00000000 0x08000000>;
};
};
};
};
&blsp1_uart1 {
pinctrl-0 = <&serial_pins>;
pinctrl-names = "default";
status = "okay";
};
&tlmm {
serial_pins: serial_pinmux {
mux {
pins = "gpio60", "gpio61";
function = "blsp_uart0";
bias-disable;
};
};
spi0_pins: spi0_pinmux {
mux_spi {
function = "blsp_spi0";
pins = "gpio55", "gpio56", "gpio57";
drive-strength = <12>;
bias-disable;
};
mux_cs {
function = "gpio";
pins = "gpio54", "gpio5";
drive-strength = <2>;
bias-disable;
output-high;
};
};
};
&usb2_hs_phy {
status = "okay";
};
&usb3_hs_phy {
status = "okay";
};
&usb3_ss_phy {
status = "okay";
};
&wifi0 {
status = "okay";
qcom,ath10k-calibration-variant = "GL-AP1300";
};
&wifi1 {
status = "okay";
qcom,ath10k-calibration-variant = "GL-AP1300";
};

15
target/linux/ipq40xx/image/Makefile
View File

@ -482,6 +482,21 @@ define Device/ezviz_cs-w3-wd1200g-eup
endef
TARGET_DEVICES += ezviz_cs-w3-wd1200g-eup
define Device/glinet_gl-ap1300
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-AP1300
SOC := qcom-ipq4018
DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 131072k
KERNEL_INSTALL := 1
DEVICE_PACKAGES := ipq-wifi-glinet_gl-ap1300
endef
TARGET_DEVICES += glinet_gl-ap1300
define Device/glinet_gl-b1300
$(call Device/FitImage)
DEVICE_VENDOR := GL.iNet

3
target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
View File

@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -837,11 +837,57 @@ dtb-$(CONFIG_ARCH_QCOM) += \
@@ -837,11 +837,58 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@ -28,6 +28,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
+ qcom-ipq4018-ex6100v2.dtb \
+ qcom-ipq4018-ex6150v2.dtb \
+ qcom-ipq4018-fritzbox-4040.dtb \
+ qcom-ipq4018-gl-ap1300.dtb \
+ qcom-ipq4018-jalapeno.dtb \
+ qcom-ipq4018-meshpoint-one.dtb \
+ qcom-ipq4018-nbg6617.dtb \