ath79: add support for jjPlus JA76PF2

jjPlus JA76PF2 (marketed as IntellusPro2) is a network embedded board.

Specification
SoC:		Atheros AR7161
RAM:		64 MB DDR
Flash:		16 MB SPI NOR
Ethernet:	2x 10/100/1000 Mbps AR8316
		LAN (CN11), WAN/PoE (CN6 - close to power barrel
		connector, 48 V)
MiniPCI:	2x
LEDS:		4x, which 3 are GPIO controlled
Buttons:	2x GPIO controlled
		Reset (SW1, closer to ethernet ports), WPS (SW2)
Serial:		1x (only RX and TX are wired)
		baud: 115200, parity: none, flow control: none

Currently there is one caveat compared to ar71xx target images as the
MAC addresses are random on every reboot. To remedy this one needs to
store the WAN MAC address in RedBoot configuration. OpenWrt on first
boot, after flashing, will read out the address and assign proper ones
to both WAN and LAN ports. It is iportant to NOT keep the old
configuration when doing sysupgrade from ar71xx.

Upgrading from OpenWrt ar71xx image
1. Connect to serial port,
2. Download OpenWrt sysupgrade image to /tmp directory and flash it
   with:
    sysupgrade -n <openwrt_sysupgrade_image_name>
3. After writing new image OpenWrt will reboot, now interrupt boot
   process and enter RedBoot (bootloader) command line by pressing
   Ctrl+C,
4. Enter following commands (replace variable accordingly),
    set_mac (to view MAC addresses)
    alias ethaddr <wan_port_mac_adress>
    (confirm storing the value by inputting y and pressing Enter)
    reset
5. Now board should restart and boot OpenWrt with proper MAC addresses.

Installation
1. Prepare TFTP server with OpenWrt initramfs image,
2. Connect to WAN ethernet port,
3. Connect to serial port,
4. Power on the board and enter RedBoot (bootloader) command line by
   pressing Ctrl+C,
5. Enter following commands (replace variables accordingly):
    set_mac (to view MAC addresses)
    alias ethaddr <wan_port_mac_address>
    (confirm storing the value by inputting y and pressing Enter)
    ip_adress -l <board_ip_adress>/24 -h <tftp_server_ip_adress>
    load -r -b 0x80060000 <openwrt_initramfs_image_name>
    exec -c ""
6. Now board should boot OpenWrt initramfs image,
7. Download OpenWrt sysupgrade image to /tmp directory and flash it
   with:
    sysupgrade <openwrt_sysupgrade_image_name>
8. Wait few minutes, after the D2 LED will stop blinking, the board
   is ready for configuration.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This commit is contained in:
Tomasz Maciej Nowak 2019-03-06 20:15:19 +01:00 committed by Christian Lamparter
parent 8f6f260302
commit b3a0c97b8c
6 changed files with 195 additions and 4 deletions

View File

@ -288,6 +288,10 @@ ath79_setup_macs()
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
wan_mac=$(macaddr_add "$lan_mac" -1)
;;
jjplus,ja76pf2)
wan_mac=$(fconfig -s -r -d $(find_mtd_part "RedBoot config") -n alias/ethaddr)
lan_mac=$(macaddr_add "$wan_mac" 1)
;;
nec,wg800hp)
lan_mac=$(mtd_get_mac_text board_data 640)
wan_mac=$(mtd_get_mac_text board_data 1152)

View File

@ -5,9 +5,10 @@
PART_NAME=firmware
REQUIRE_IMAGE_METADATA=1
routerstation_do_upgrade() {
redboot_fis_do_upgrade() {
local append
local sysup_file="$1"
local kern_part="$2"
local magic=$(get_magic_word "$sysup_file")
if [ "$magic" = "4349" ]; then
@ -15,7 +16,7 @@ routerstation_do_upgrade() {
[ -f "$CONF_TAR" -a "$SAVE_CONFIG" -eq 1 ] && append="-j $CONF_TAR"
dd if="$sysup_file" bs=64k skip=1 2>/dev/null | \
mtd -r $append -Fkernel:$kern_length:0x80060000,rootfs write - kernel:rootfs
mtd -r $append -F$kern_part:$kern_length:0x80060000,rootfs write - $kern_part:rootfs
elif [ "$magic" = "7379" ]; then
local board_dir=$(tar tf $sysup_file | grep -m 1 '^sysupgrade-.*/$')
@ -23,7 +24,7 @@ routerstation_do_upgrade() {
[ -f "$CONF_TAR" -a "$SAVE_CONFIG" -eq 1 ] && append="-j $CONF_TAR"
tar xf $sysup_file ${board_dir}kernel ${board_dir}root -O | \
mtd -r $append -Fkernel:$kern_length:0x80060000,rootfs write - kernel:rootfs
mtd -r $append -F$kern_part:$kern_length:0x80060000,rootfs write - $kern_part:rootfs
else
echo "Unknown image, aborting!"
@ -39,9 +40,12 @@ platform_do_upgrade() {
local board=$(board_name)
case "$board" in
jjplus,ja76pf2)
redboot_fis_do_upgrade "$ARGV" linux
;;
ubnt,routerstation|\
ubnt,routerstation-pro)
routerstation_do_upgrade "$ARGV"
redboot_fis_do_upgrade "$ARGV" kernel
;;
*)
default_do_upgrade "$ARGV"

View File

@ -0,0 +1,126 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "ar7100.dtsi"
/ {
model = "jjPlus JA76PF2";
compatible = "jjplus,ja76pf2", "qca,ar7161";
memory@0 {
device_type = "memory";
reg = <0x0 0x4000000>;
};
chosen {
bootargs = "console=ttyS0,115200n8";
};
aliases {
led-boot = &d2;
led-failsafe = &d2;
led-running = &d2;
led-upgrade = &d2;
};
extosc: ref {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-output-names = "ref";
clock-frequency = <40000000>;
};
leds {
compatible = "gpio-leds";
d2: d2 {
label = "ja76pf2:green:d2";
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
};
d3 {
label = "ja76pf2:green:d3";
gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
};
d4 {
label = "ja76pf2:green:d4";
gpios = <&gpio 3 GPIO_ACTIVE_HIGH>;
};
};
keys {
compatible = "gpio-keys-polled";
poll-interval = <20>;
sw1 {
label = "sw1";
linux,code = <KEY_RESTART>;
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
sw2 {
label = "sw2";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
};
&mdio0 {
status = "okay";
phy-mask = <0x1>;
phy0: ethernet-phy@0 {
reg = <0>;
phy-mode = "rgmii";
};
phy4: ethernet-phy@4 {
reg = <4>;
phy-mode = "rgmii";
};
};
&eth0 {
status = "okay";
phy-handle = <&phy0>;
};
&eth1 {
status = "okay";
phy-handle = <&phy4>;
};
&pcie0 {
status = "okay";
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <104000000>;
partitions {
#address-cells = <1>;
#size-cells = <1>;
compatible = "ecoscentric,redboot-fis-partitions";
};
};
};
&uart {
status = "okay";
};

View File

@ -8,6 +8,7 @@ CONFIG_LEDS_RESET=y
CONFIG_MARVELL_PHY=y
CONFIG_MICREL_PHY=y
CONFIG_MTD_REDBOOT_PARTS=y
CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-2
CONFIG_MTD_SPLIT_EVA_FW=y
CONFIG_OF_ADDRESS_PCI=y
CONFIG_OF_PCI=y

View File

@ -417,6 +417,18 @@ define Device/iodata_wn-ag300dgr
endef
TARGET_DEVICES += iodata_wn-ag300dgr
define Device/jjplus_ja76pf2
ATH_SOC := ar7161
DEVICE_TITLE := jjPlus JA76PF2
DEVICE_PACKAGES += -kmod-ath9k -swconfig -wpad-mini -uboot-envtools fconfig
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | combined-image | check-size $$$$(IMAGE_SIZE)
# IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
KERNEL := kernel-bin | append-dtb | lzma | pad-to $$(BLOCKSIZE)
KERNEL_INITRAMFS := kernel-bin | append-dtb
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += jjplus_ja76pf2
define Device/librerouter_librerouter-v1
ATH_SOC := qca9558
DEVICE_TITLE := LibreRouter v1

View File

@ -0,0 +1,44 @@
--- a/drivers/mtd/redboot.c
+++ b/drivers/mtd/redboot.c
@@ -76,12 +76,18 @@ static int parse_redboot_partitions(stru
static char nullstring[] = "unallocated";
#endif
+ buf = vmalloc(master->erasesize);
+ if (!buf)
+ return -ENOMEM;
+
+ restart:
if ( directory < 0 ) {
offset = master->size + directory * master->erasesize;
while (mtd_block_isbad(master, offset)) {
if (!offset) {
nogood:
printk(KERN_NOTICE "Failed to find a non-bad block to check for RedBoot partition table\n");
+ vfree(buf);
return -EIO;
}
offset -= master->erasesize;
@@ -94,10 +100,6 @@ static int parse_redboot_partitions(stru
goto nogood;
}
}
- buf = vmalloc(master->erasesize);
-
- if (!buf)
- return -ENOMEM;
printk(KERN_NOTICE "Searching for RedBoot partition table in %s at offset 0x%lx\n",
master->name, offset);
@@ -170,6 +172,11 @@ static int parse_redboot_partitions(stru
}
if (i == numslots) {
/* Didn't find it */
+ if (offset + master->erasesize < master->size) {
+ /* not at the end of the flash yet, maybe next block :) */
+ directory++;
+ goto restart;
+ }
printk(KERN_NOTICE "No RedBoot partition table detected in %s\n",
master->name);
ret = 0;