ath79: add support for Aruba AP-105

SoC: Atheros AR7161-8C1A @ 680 MHz
RAM: 128MB - 2x Etron Technology EM6AB160TSA-5G
NOR: 16MB - 1x MXIC MX25L12845EMI-10G (SPI-NOR)
WI1: Atheros AR9223-AC1A 802.11bgn
WI2: Atheros AR9220-AC1A 802.11an
ETH: Atheros AR8021-BL1E + PoE
LED: Dual-Color Power/Status, Ethernet, WLAN2G and WLAN5G
BTN: 1 x Reset
I2C: AT97SC4303s TPM (needs driver!)
CON: RS232-level 8P8C/RJ45 Console Port - 9600 Baud

Factory installation:

 - Needs a u-boot replacement. See Wiki for
   information on how to do a in-circut flash with
   a SPI-Flasher like a CH314A or flashrom. Wiki page
   can be found at https://openwrt.org/toh/aruba/aruba_ap-105

 - Be careful when dis- and reassembling the device to
   not squish any of the antenna cables in the process!

 - Be sure to make a full 16 MiB backup of your device
   before flashing the new u-boot! This is needed if you
   ever have interest in reverting back to stock firmware.

Not working:

 - TPM (needs a driver)

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This commit is contained in:
Chris Blake 2019-05-05 12:56:03 -05:00 committed by Christian Lamparter
parent 2fdd02cc7c
commit aee5c98619
3 changed files with 199 additions and 0 deletions

View File

@ -9,6 +9,7 @@ ath79_setup_interfaces()
local board="$1"
case "$board" in
aruba,ap-105|\
avm,fritz300e|\
devolo,dvl1200i|\
devolo,dvl1750c|\

View File

@ -0,0 +1,190 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "ar7100.dtsi"
/ {
compatible = "aruba,ap-105", "qca,ar7161";
model = "Aruba AP-105";
chosen {
bootargs = "console=ttyS0,9600";
};
aliases {
led-boot = &power_green;
led-failsafe = &power_red;
led-running = &power_green;
led-upgrade = &power_green;
};
extosc: ref {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-output-names = "ref";
clock-frequency = <40000000>;
};
leds {
compatible = "gpio-leds";
power_green: power_green {
label = "ap-105:green:power";
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
};
power_red: power_red {
label = "ap-105:red:power";
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
panic-indicator;
};
wifi_2g_red: wifi_2g_red {
label = "ap-105:red:wlan2g";
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
};
wifi_5g_red: wifi_5g_red {
label = "ap-105:red:wlan5g";
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
};
};
ath9k-leds {
compatible = "gpio-leds";
wifi_2g_green {
label = "ap-105:green:wlan2g";
gpios = <&ath9k0 5 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
wifi_5g_green {
label = "ap-105:green:wlan5g";
gpios = <&ath9k1 5 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy1tpt";
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
};
};
i2c {
compatible = "i2c-gpio";
sda-gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
scl-gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
/* can be removed on 4.19 */
gpios = <&gpio 5 GPIO_ACTIVE_LOW>,
<&gpio 4 GPIO_ACTIVE_LOW>;
#address-cells = <1>;
#size-cells = <0>;
tpm@29 {
compatible = "atmel,at97sc3203s";
reg = <0x29>;
/* triggering it, will also kill system */
reset-gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
};
};
};
&pcie0 {
status = "okay";
ath9k0: wifi@0,11 { /* 2.4 GHz */
compatible = "pci168c,0029";
mtd-mac-address = <&hwinfo 0x1c>;
mtd-mac-address-increment = <1>;
reg = <0x8800 0 0 0 0>;
#gpio-cells = <2>;
gpio-controller;
};
ath9k1: wifi@0,12 { /* 5 GHz */
compatible = "pci168c,0029";
mtd-mac-address = <&hwinfo 0x1c>;
mtd-mac-address-increment = <2>;
reg = <0x9000 0 0 0 0>;
#gpio-cells = <2>;
gpio-controller;
};
};
&uart {
status = "okay";
};
&mdio0 {
status = "okay";
phy-mask = <0x1>;
phy0: ethernet-phy@0 {
reg = <0>;
};
};
&eth0 {
status = "okay";
mtd-mac-address = <&hwinfo 0x1c>;
pll-data = <0x00110000 0x00001099 0x00991099>;
phy-mode = "rgmii";
phy-handle = <&phy0>;
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x40000>;
read-only;
};
partition@40000 {
label = "firmware";
reg = <0x40000 0xfa0000>;
compatible = "denx,uimage";
};
hwinfo: partition@fe0000 {
label = "hwinfo";
reg = <0xfe0000 0x10000>;
read-only;
};
partition@ff0000 {
label = "u-boot-env";
reg = <0xff0000 0x10000>;
read-only;
};
};
};
};

View File

@ -75,6 +75,14 @@ define Device/seama
SEAMA_SIGNATURE :=
endef
define Device/aruba_ap-105
ATH_SOC := ar7161
DEVICE_TITLE := Aruba AP-105
IMAGE_SIZE := 16000k
DEVICE_PACKAGES := kmod-i2c-core kmod-i2c-gpio kmod-tpm-i2c-atmel
endef
TARGET_DEVICES += aruba_ap-105
define Device/avm_fritz300e
ATH_SOC := ar7242
DEVICE_TITLE := AVM FRITZ!WLAN Repeater 300E