mirror
/
openwrt
mirror of https://git.openwrt.org/openwrt/openwrt.git
1
0
Fork 0
Code Releases Activity

ipq40xx: Add support for Linksys MR8300 (Dallas) 

The Linksys MR8300 is based on QCA4019 and QCA9888
and provides three, independent radios.
NAND provides two, alternate kernel/firmware images
with fail-over provided by the OEM U-Boot.

Hardware Highlights:

SoC: IPQ4019 at 717 MHz (4 CPUs)
RAM: 512MB RAM

SoC:	Qualcomm IPQ4019 at 717 MHz (4 CPUs)
RAM:	512M DDR3
FLASH:	256 MB NAND (Winbond W29N02GV, 8-bit parallel)
ETH:	Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks)
BTN:	Reset and WPS
USB:	USB3.0, single port on rear with LED
SERIAL:	Serial pads internal (unpopulated)
LED:	Four status lights on top + USB LED
WIFI1:	2x2:2 QCA4019 2.4 GHz radio on ch. 1-14
WIFI2:  2x2:2 QCA4019 5 GHz radio on ch. 36-64
WIFI3:  2x2:2 QCA9888 5 GHz radio on ch. 100-165

Support is based on the already supported EA8300.
Key differences:
	EA8300 has 256MB RAM where MR8300 has 512MB RAM.
	MR8300 has a revised top panel LED setup.

Installation:
"Factory" images may be installed directly through the OEM GUI using
URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1)

Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com>
[copied Hardware-highlights from EA8300. Fixed alphabetical order.
fixed commit subject, removed bogus unit-address of keys,
fixed author (used Signed-off-By to From:) ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit is contained in:
Hans Geiblinger 2020-09-09 18:45:02 -04:00 committed by Christian Lamparter
parent e24635710c
commit a9071d02b5
16 changed files with 425 additions and 315 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

3
package/boot/uboot-envtools/files/ipq40xx
View File

@ -45,7 +45,8 @@ buffalo,wtr-m2133hp)
linksys,ea6350v3)
ubootenv_add_uci_config "/dev/mtd7" "0x0" "0x20000" "0x20000"
;;
linksys,ea8300)
linksys,ea8300 |\
linksys,mr8300)
ubootenv_add_uci_config "/dev/mtd7" "0x0" "0x40000" "0x20000"
;;
zyxel,nbg6617)

2
package/firmware/ipq-wifi/Makefile
View File

@ -40,6 +40,7 @@ ALLWIFIBOARDS:= \
ezviz_cs-w3-wd1200g-eup \
glinet_gl-s1300 \
linksys_ea8300 \
linksys_mr8300-v0 \
luma_wrtq-329acn \
mobipromo_cm520-79f \
qxwlan_e2600ac
@ -118,6 +119,7 @@ $(eval $(call generate-ipq-wifi-package,engenius_emr3500,EnGenius EMR3500))
$(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP))
$(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300))
$(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
$(eval $(call generate-ipq-wifi-package,linksys_mr8300-v0,Linksys MR8300))
$(eval $(call generate-ipq-wifi-package,luma_wrtq-329acn,Luma WRTQ-329ACN))
$(eval $(call generate-ipq-wifi-package,mobipromo_cm520-79f,MobiPromo CM520-79F))
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC))

BIN
package/firmware/ipq-wifi/board-linksys_mr8300-v0.qca4019 Normal file
View File

Binary file not shown.

BIN
package/firmware/ipq-wifi/board-linksys_mr8300-v0.qca9888 Normal file
View File

Binary file not shown.

3
target/linux/ipq40xx/base-files/etc/board.d/02_network
View File

@ -53,7 +53,8 @@ ipq40xx_setup_interfaces()
;;
avm,fritzbox-4040|\
linksys,ea6350v3|\
linksys,ea8300)
linksys,ea8300|\
linksys,mr8300)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"

9
target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
View File

@ -39,7 +39,8 @@ case "$FIRMWARE" in
openmesh,a62)
caldata_extract "0:ART" 0x9000 0x2f20
;;
linksys,ea8300)
linksys,ea8300 |\
linksys,mr8300)
caldata_extract "ART" 0x9000 0x2f20
# OEM assigns 4 sequential MACs
ath10k_patch_mac $(macaddr_setbit_la $(macaddr_add "$(cat /sys/class/net/eth0/address)" 4))
@ -121,7 +122,8 @@ case "$FIRMWARE" in
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +2)
;;
linksys,ea8300)
linksys,ea8300 |\
linksys,mr8300)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" 2)
;;
@ -217,7 +219,8 @@ case "$FIRMWARE" in
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +3)
;;
linksys,ea8300)
linksys,ea8300 |\
linksys,mr8300)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" 3)
;;

3
target/linux/ipq40xx/base-files/etc/init.d/bootcount
View File

@ -9,7 +9,8 @@ boot() {
echo -e "bootcount\nchanged\n" | /usr/sbin/fw_setenv -s -
;;
linksys,ea6350v3|\
linksys,ea8300)
linksys,ea8300|\
linksys,mr8300)
mtd resetbc s_env || true
;;
esac

3
target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
View File

@ -15,7 +15,8 @@ preinit_set_mac_address() {
base_mac=$(cat /sys/class/net/eth0/address)
ip link set dev eth1 address $(macaddr_add "${base_mac}" +1)
;;
linksys,ea8300)
linksys,ea8300|\
linksys,mr8300)
base_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
ip link set dev eth0 address "${base_mac}"
ip link set dev eth1 address $(macaddr_add "${base_mac}" 1)

1
target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh
View File

@ -8,6 +8,7 @@ set_preinit_iface() {
ezviz,cs-w3-wd1200g-eup| \
glinet,gl-b1300| \
linksys,ea8300| \
linksys,mr8300| \
meraki,mr33| \
zyxel,nbg6617)
ifname=eth0

2
target/linux/ipq40xx/base-files/lib/upgrade/linksys.sh
View File

@ -16,7 +16,7 @@ linksys_get_target_firmware() {
"${cur_boot_part}" "${mtd_ubi0}"
fi
# OEM U-Boot for EA6350v3 and EA8300; bootcmd=
# OEM U-Boot for EA6350v3, EA8300 and MR8300; bootcmd=
# if test $auto_recovery = no;
# then bootipq;
# elif test $boot_part = 1;

3
target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
View File

@ -102,7 +102,8 @@ platform_do_upgrade() {
nand_do_upgrade "$1"
;;
linksys,ea6350v3 |\
linksys,ea8300)
linksys,ea8300 |\
linksys,mr8300)
platform_do_upgrade_linksys "$1"
;;
meraki,mr33)

308
target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-ea8300.dts
View File

@ -1,18 +1,8 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
* Device Tree Source for Linksys EA8300 (Dallas)
*
* Copyright (C) 2019 Jeff Kletsky
*
*/
/dts-v1/;
#include "qcom-ipq4019.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/soc/qcom,tcsr.h>
#include "qcom-ipq4019-xx8300.dtsi"
/ {
model = "Linksys EA8300 (Dallas)";
@ -72,313 +62,21 @@
};
};
keys {
compatible = "gpio-keys";
button@0 {
reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
};
button@1 {
wps {
label = "wps";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
};
};
//
// OEM U-Boot provides either
// init=/sbin/init rootfstype=ubifs ubi.mtd=11,2048 \
// root=ubi0:ubifs rootwait rw
// or the same with ubi.mtd=13,2048
//
chosen {
bootargs-append = " root=/dev/ubiblock0_0 rootfstype=squashfs ro";
};
memory {
device_type = "memory";
reg = <0x80000000 0x10000000>;
};
soc {
rng@22000 {
status = "okay";
};
mdio@90000 {
status = "okay";
};
ess-psgmii@98000 {
status = "okay";
};
tcsr@1949000 {
compatible = "qcom,tcsr";
reg = <0x1949000 0x100>;
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
};
tcsr@194b000 {
compatible = "qcom,tcsr";
reg = <0x194b000 0x100>;
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
};
ess_tcsr@1953000 {
compatible = "qcom,tcsr";
reg = <0x1953000 0x1000>;
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
};
tcsr@1957000 {
compatible = "qcom,tcsr";
reg = <0x1957000 0x100>;
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
};
usb2@60f8800 {
status = "okay";
dwc3@6000000 {
#address-cells = <1>;
#size-cells = <0>;
usb2_port1: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
};
};
usb3@8af8800 {
status = "okay";
dwc3@8a00000 {
#address-cells = <1>;
#size-cells = <0>;
usb3_port1: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
usb3_port2: port@2 {
reg = <2>;
#trigger-source-cells = <0>;
};
};
};
crypto@8e3a000 {
status = "okay";
};
watchdog@b017000 {
status = "okay";
};
ess-switch@c000000 {
status = "okay";
};
edma@c080000 {
status = "okay";
};
};
};
&blsp_dma {
status = "okay";
};
&blsp1_uart1 {
status = "okay";
pinctrl-0 = <&serial_0_pins>;
pinctrl-names = "default";
};
&cryptobam {
status = "okay";
};
&nand {
status = "okay";
pinctrl-0 = <&nand_pins>;
pinctrl-names = "default";
nand@0 {
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "sbl1";
reg = <0x0 0x100000>;
read-only;
};
partition@100000 {
label = "mibib";
reg = <0x100000 0x100000>;
read-only;
};
partition@200000 {
label = "qsee";
reg = <0x200000 0x100000>;
read-only;
};
partition@300000 {
label = "cdt";
reg = <0x300000 0x80000>;
read-only;
};
partition@380000 {
label = "appsblenv";
reg = <0x380000 0x80000>;
read-only;
};
partition@400000 {
label = "ART";
reg = <0x400000 0x80000>;
read-only;
};
partition@480000 {
label = "appsbl";
reg = <0x480000 0x200000>;
read-only;
};
partition@680000 {
label = "u_env";
reg = <0x680000 0x80000>;
// writable -- U-Boot environment
};
partition@700000 {
label = "s_env";
reg = <0x700000 0x40000>;
// writable -- Boot counter records
};
partition@740000 {
label = "devinfo";
reg = <0x740000 0x40000>;
read-only;
};
partition@780000 {
label = "kernel";
reg = <0x780000 0x5800000>;
};
partition@a80000 {
label = "rootfs";
reg = <0xa80000 0x5500000>;
};
partition@5f80000 {
label = "alt_kernel";
reg = <0x5f80000 0x5800000>;
};
partition@6280000 {
label = "alt_rootfs";
reg = <0x6280000 0x5500000>;
};
partition@b780000 {
label = "sysdiag";
reg = <0xb780000 0x100000>;
read-only;
};
partition@b880000 {
label = "syscfg";
reg = <0xb880000 0x4680000>;
read-only;
};
};
};
};
&pcie0 {
status = "okay";
perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
bridge@0,0 {
reg = <0x00000000 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
ranges;
wifi2: wifi@1,0 {
compatible = "qcom,ath10k";
reg = <0x00010000 0 0 0 0>;
};
};
};
&qpic_bam {
status = "okay";
};
&tlmm {
serial_0_pins: serial0-pinmux {
pins = "gpio16", "gpio17";
function = "blsp_uart0";
bias-disable;
};
nand_pins: nand_pins {
pullups {
pins = "gpio53", "gpio58", "gpio59";
function = "qpic";
bias-pull-up;
};
// gpio61 controls led_usb
pulldowns {
pins = "gpio55", "gpio56", "gpio57",
"gpio60", "gpio62", "gpio63",
"gpio64", "gpio65", "gpio66",
"gpio67", "gpio68", "gpio69";
function = "qpic";
bias-pull-down;
};
};
};
&usb2_hs_phy {
status = "okay";
};
&usb3_hs_phy {
status = "okay";
};
&usb3_ss_phy {
status = "okay";
};
&wifi0 {

82
target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-mr8300.dts Normal file
View File

@ -0,0 +1,82 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "qcom-ipq4019-xx8300.dtsi"
/ {
model = "Linksys MR8300 (Dallas)";
compatible = "linksys,mr8300", "qcom,ipq4019";
aliases {
led-boot = &led_blue;
led-failsafe = &led_red;
led-running = &led_blue;
led-upgrade = &led_amber;
serial0 = &blsp1_uart1;
};
// Top panel LEDs, above Linksys logo
leds {
compatible = "gpio-leds";
led_red: red {
label = "mr8300:red:alarm";
gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>;
};
led_amber: amber {
label = "mr8300:amber:programming";
gpios = <&tlmm 22 GPIO_ACTIVE_HIGH>;
panic-indicator;
};
led_blue: blue {
label = "mr8300:blue:power";
gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>;
};
// On back panel, above USB socket
led_usb: usb {
label = "mr8300:green:usb";
gpios = <&tlmm 61 GPIO_ACTIVE_LOW>;
trigger-sources = <&usb3_port1>, <&usb3_port2>,
<&usb2_port1>;
linux,default-trigger = "usbport";
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
};
wps {
label = "wps";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
};
};
};
&wifi0 {
status = "okay";
qcom,ath10k-calibration-variant = "linksys-mr8300-v0-fcc";
};
&wifi1 {
status = "okay";
ieee80211-freq-limit = <5170000 5330000>;
qcom,ath10k-calibration-variant = "linksys-mr8300-v0-fcc";
};
&wifi2 {
status = "okay";
ieee80211-freq-limit = <5490000 5835000>;
qcom,ath10k-calibration-variant = "linksys-mr8300-v0-fcc";
};

302
target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-xx8300.dtsi Normal file
View File

@ -0,0 +1,302 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
* Device Tree Source for Linksys xx8300 (Dallas)
*
* Copyright (C) 2019 Jeff Kletsky
* Updated 2020 Hans Geiblinger
*
*/
/dts-v1/;
#include "qcom-ipq4019.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/soc/qcom,tcsr.h>
//
// OEM U-Boot provides either
// init=/sbin/init rootfstype=ubifs ubi.mtd=11,2048 \
// root=ubi0:ubifs rootwait rw
// or the same with ubi.mtd=13,2048
//
/ {
chosen {
bootargs-append = " root=/dev/ubiblock0_0 rootfstype=squashfs ro";
};
soc {
rng@22000 {
status = "okay";
};
mdio@90000 {
status = "okay";
};
ess-psgmii@98000 {
status = "okay";
};
tcsr@1949000 {
compatible = "qcom,tcsr";
reg = <0x1949000 0x100>;
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
};
tcsr@194b000 {
compatible = "qcom,tcsr";
reg = <0x194b000 0x100>;
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
};
ess_tcsr@1953000 {
compatible = "qcom,tcsr";
reg = <0x1953000 0x1000>;
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
};
tcsr@1957000 {
compatible = "qcom,tcsr";
reg = <0x1957000 0x100>;
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
};
usb2@60f8800 {
status = "okay";
dwc3@6000000 {
#address-cells = <1>;
#size-cells = <0>;
usb2_port1: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
};
};
usb3@8af8800 {
status = "okay";
dwc3@8a00000 {
#address-cells = <1>;
#size-cells = <0>;
usb3_port1: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
usb3_port2: port@2 {
reg = <2>;
#trigger-source-cells = <0>;
};
};
};
crypto@8e3a000 {
status = "okay";
};
watchdog@b017000 {
status = "okay";
};
ess-switch@c000000 {
status = "okay";
};
edma@c080000 {
status = "okay";
};
};
};
&blsp_dma {
status = "okay";
};
&blsp1_uart1 {
status = "okay";
pinctrl-0 = <&serial_0_pins>;
pinctrl-names = "default";
};
&cryptobam {
status = "okay";
};
&nand {
status = "okay";
pinctrl-0 = <&nand_pins>;
pinctrl-names = "default";
nand@0 {
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "sbl1";
reg = <0x0 0x100000>;
read-only;
};
partition@100000 {
label = "mibib";
reg = <0x100000 0x100000>;
read-only;
};
partition@200000 {
label = "qsee";
reg = <0x200000 0x100000>;
read-only;
};
partition@300000 {
label = "cdt";
reg = <0x300000 0x80000>;
read-only;
};
partition@380000 {
label = "appsblenv";
reg = <0x380000 0x80000>;
read-only;
};
partition@400000 {
label = "ART";
reg = <0x400000 0x80000>;
read-only;
};
partition@480000 {
label = "appsbl";
reg = <0x480000 0x200000>;
read-only;
};
partition@680000 {
label = "u_env";
reg = <0x680000 0x80000>;
// writable -- U-Boot environment
};
partition@700000 {
label = "s_env";
reg = <0x700000 0x40000>;
// writable -- Boot counter records
};
partition@740000 {
label = "devinfo";
reg = <0x740000 0x40000>;
read-only;
};
partition@780000 {
label = "kernel";
reg = <0x780000 0x5800000>;
};
partition@a80000 {
label = "rootfs";
reg = <0xa80000 0x5500000>;
};
partition@5f80000 {
label = "alt_kernel";
reg = <0x5f80000 0x5800000>;
};
partition@6280000 {
label = "alt_rootfs";
reg = <0x6280000 0x5500000>;
};
partition@b780000 {
label = "sysdiag";
reg = <0xb780000 0x100000>;
read-only;
};
partition@b880000 {
label = "syscfg";
reg = <0xb880000 0x4680000>;
read-only;
};
};
};
};
&pcie0 {
status = "okay";
perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
bridge@0,0 {
reg = <0x00000000 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
ranges;
wifi2: wifi@1,0 {
compatible = "qcom,ath10k";
reg = <0x00010000 0 0 0 0>;
};
};
};
&qpic_bam {
status = "okay";
};
&tlmm {
serial_0_pins: serial0-pinmux {
pins = "gpio16", "gpio17";
function = "blsp_uart0";
bias-disable;
};
nand_pins: nand_pins {
pullups {
pins = "gpio53", "gpio58", "gpio59";
function = "qpic";
bias-pull-up;
};
// gpio61 controls led_usb
pulldowns {
pins = "gpio55", "gpio56", "gpio57",
"gpio60", "gpio62", "gpio63",
"gpio64", "gpio65", "gpio66",
"gpio67", "gpio68", "gpio69";
function = "qpic";
bias-pull-down;
};
};
};
&usb2_hs_phy {
status = "okay";
};
&usb3_hs_phy {
status = "okay";
};
&usb3_ss_phy {
status = "okay";
};

16
target/linux/ipq40xx/image/Makefile
View File

@ -540,6 +540,22 @@ define Device/linksys_ea8300
endef
TARGET_DEVICES += linksys_ea8300
define Device/linksys_mr8300
$(call Device/FitzImage)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := MR8300
SOC := qcom-ipq4019
KERNEL_SIZE := 3072k
IMAGE_SIZE := 87040k
BLOCKSIZE := 128k
PAGESIZE := 2048
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=MR8300
DEVICE_PACKAGES := uboot-envtools ath10k-firmware-qca9888-ct ipq-wifi-linksys_mr8300-v0 kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += linksys_mr8300
define Device/luma_wrtq-329acn
$(call Device/FitImage)
DEVICE_VENDOR := Luma Home

3
target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
View File

@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -837,11 +837,53 @@ dtb-$(CONFIG_ARCH_QCOM) += \
@@ -837,11 +837,54 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@ -47,6 +47,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
+ qcom-ipq4019-fritzrepeater-1200.dtb \
+ qcom-ipq4019-fritzrepeater-3000.dtb \
+ qcom-ipq4019-map-ac2200.dtb \
+ qcom-ipq4019-mr8300.dtb \
+ qcom-ipq4019-e2600ac-c1.dtb \
+ qcom-ipq4019-e2600ac-c2.dtb \
+ qcom-ipq4019-habanero-dvk.dtb \