ath79: add support for TP-Link EAP245-v3
TP-Link EAP245 v3 is an AC1750 (802.11ac Wave-2) ceiling mount access
point. UART access (for debricking) requires non-trivial soldering.
Specifications:
* SoC: QCA9563 (CPU/DDR/AHB @ 775/650/258 MHz)
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n 3x3
* Wireless 5GHz (QCA9982): a/n/ac 3x3 with MU-MIMO
* Ethernet (QCA8337N switch): 2× 1GbE, ETH1 (802.3at PoE) and ETH2
* Green and amber status LEDs
* Reset switch (GPIO, available for failsafe)
Flashing instructions:
All recent firmware versions (latest is 2.20.0), can disable firmware
signature verification and use a padded firmware file to flash OpenWrt:
* ssh into target device and run `cliclientd stopcs`
* upload factory image via web interface
The stopcs-method is supported from firmware version 2.3.0. Earlier
versions need to be upgraded to a newer stock version before flashing
OpenWrt.
Factory images for these devices are RSA signed by TP-Link. While the
signature verification can be disabled, the factory image still needs to
have a (fake) 1024 bit signature added to pass file checks.
Debricking instructions:
You can recover using u-boot via the serial port:
* Serial port is available from J3 (1:TX, 2:RX, 3:GND, 4:3.3V)
* Bridge R237 to connect RX, located next to J3
* Bridge R225 to connect TX, located inside can on back-side of board
* Serial port is 115200 baud, 8n1, interrupt u-boot by holding ctrl+B
* Upload initramfs with tftp and upgrade via OpenWrt
Device mac addresses:
Stock firmware has the same mac address for 2.4GHz wireless and
ethernet, 5GHz is incremented by one. The base mac address is stored in
the 'default-mac' partition (offset 0x90000) at an offset of 8 bytes.
ART blobs contain no mac addresses.
From OEM ifconfig:
ath0 Link encap:Ethernet HWaddr 74:..:E2
ath10 Link encap:Ethernet HWaddr 74:..:E3
br0 Link encap:Ethernet HWaddr 74:..:E2
eth0 Link encap:Ethernet HWaddr 74:..:E2
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
This commit is contained in:
Sander Vanheule
Stijn Tintel
parent
14464e1128
commit
9dd4ba3d7e
|
|
@ -0,0 +1,163 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "qca956x.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "tplink,eap245-v3", "qca,qca9563";
|
||||
model = "TP-Link EAP245 v3";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_status_green;
|
||||
led-failsafe = &led_status_amber;
|
||||
led-running = &led_status_green;
|
||||
led-upgrade = &led_status_amber;
|
||||
label-mac-device = ð0;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_status_green: status_green {
|
||||
label = "tp-link:green:status";
|
||||
gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
led_status_amber: status_amber {
|
||||
label = "tp-link:amber:status";
|
||||
gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "Reset button";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "factory-boot";
|
||||
reg = <0x000000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "u-boot";
|
||||
reg = <0x040000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
label = "partition-table";
|
||||
reg = <0x080000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
info: partition@90000 {
|
||||
label = "info";
|
||||
reg = <0x090000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@a0000 {
|
||||
label = "art";
|
||||
reg = <0x0a0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@b0000 {
|
||||
label = "extra-para";
|
||||
reg = <0x0b0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@c0000 {
|
||||
compatible = "openwrt,elf";
|
||||
label = "firmware";
|
||||
reg = <0x0c0000 0xe40000>;
|
||||
};
|
||||
|
||||
partition@f00000 {
|
||||
label = "config";
|
||||
reg = <0xf00000 0x030000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@f30000 {
|
||||
label = "mutil-log";
|
||||
reg = <0xf30000 0x080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@fb0000 {
|
||||
label = "oops";
|
||||
reg = <0xfb0000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
phy-mask = <0x1>;
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
phy-mode = "sgmii";
|
||||
qca,ar8327-initvals = <
|
||||
0x04 0x00080080 /* PAD0 */
|
||||
0x7c 0x0000007e /* PORT0_STATUS */
|
||||
0xe0 0xc74164de /* SGMII_CTRL */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
phy-handle = <&phy0>;
|
||||
phy-mode = "sgmii";
|
||||
|
||||
mtd-mac-address = <&info 0x8>;
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
mtd-cal-data = <&art 0x1000>;
|
||||
mtd-mac-address = <&info 0x8>;
|
||||
};
|
||||
|
|
@ -301,6 +301,10 @@ ath79_setup_interfaces()
|
|||
ucidef_add_switch "switch0" \
|
||||
"0@eth1" "3:lan:3" "4:lan:2" "5:lan:1" "6@eth0" "2:wan:4" "1:wan:5"
|
||||
;;
|
||||
tplink,eap245-v3)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "2:lan:1" "5:lan:2"
|
||||
;;
|
||||
tplink,tl-mr6400-v1)
|
||||
ucidef_set_interfaces_lan_wan "eth0.1 eth1" "usb0"
|
||||
ucidef_add_switch "switch0" \
|
||||
|
|
|
|||
|
|
@ -206,6 +206,10 @@ case "$FIRMWARE" in
|
|||
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
||||
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
||||
;;
|
||||
tplink,eap245-v3)
|
||||
caldata_extract "art" 0x5000 0x2f20
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) +1)
|
||||
;;
|
||||
yuncore,a782|\
|
||||
yuncore,xd4200)
|
||||
caldata_extract "art" 0x5000 0x2f20
|
||||
|
|
|
|||
|
|
@ -362,6 +362,26 @@ define Device/tplink_cpe610-v2
|
|||
endef
|
||||
TARGET_DEVICES += tplink_cpe610-v2
|
||||
|
||||
define Device/tplink-eap2x5
|
||||
$(Device/tplink-safeloader)
|
||||
SOC := qca9563
|
||||
LOADER_TYPE := elf
|
||||
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel
|
||||
KERNEL_INITRAMFS := $$(KERNEL)
|
||||
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory | \
|
||||
pad-extra 128
|
||||
endef
|
||||
|
||||
define Device/tplink_eap245-v3
|
||||
$(Device/tplink-eap2x5)
|
||||
IMAGE_SIZE := 14592k
|
||||
DEVICE_MODEL := EAP245
|
||||
DEVICE_VARIANT := v3
|
||||
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca99x0-ct
|
||||
TPLINK_BOARD_ID := EAP245-V3
|
||||
endef
|
||||
TARGET_DEVICES += tplink_eap245-v3
|
||||
|
||||
define Device/tplink_re350k-v1
|
||||
$(Device/tplink-safeloader)
|
||||
SOC := qca9558
|
||||
|
|
|
|||
|
|
@ -1298,6 +1298,38 @@ static struct device_info boards[] = {
|
|||
.last_sysupgrade_partition = "file-system"
|
||||
},
|
||||
|
||||
/** Firmware layout for the EAP245 v3 */
|
||||
{
|
||||
.id = "EAP245-V3",
|
||||
.support_list =
|
||||
"SupportList:\r\n"
|
||||
"EAP245(TP-Link|UN|AC1750-D):3.0\r\n",
|
||||
.support_trail = '\xff',
|
||||
.soft_ver = NULL,
|
||||
.soft_ver_compat_level = 1,
|
||||
|
||||
/** Firmware partition with dynamic kernel/rootfs split */
|
||||
.partitions = {
|
||||
{"factroy-boot", 0x00000, 0x40000},
|
||||
{"fs-uboot", 0x40000, 0x40000},
|
||||
{"partition-table", 0x80000, 0x10000},
|
||||
{"default-mac", 0x90000, 0x01000},
|
||||
{"support-list", 0x91000, 0x00100},
|
||||
{"product-info", 0x91100, 0x00400},
|
||||
{"soft-version", 0x92000, 0x00100},
|
||||
{"radio", 0xa0000, 0x10000},
|
||||
{"extra-para", 0xb0000, 0x10000},
|
||||
{"firmware", 0xc0000, 0xe40000},
|
||||
{"config", 0xf00000, 0x30000},
|
||||
{"mutil-log", 0xf30000, 0x80000},
|
||||
{"oops", 0xfb0000, 0x40000},
|
||||
{NULL, 0, 0}
|
||||
},
|
||||
|
||||
.first_sysupgrade_partition = "os-image",
|
||||
.last_sysupgrade_partition = "file-system"
|
||||
},
|
||||
|
||||
/** Firmware layout for the TL-WA850RE v2 */
|
||||
{
|
||||
.id = "TLWA850REV2",
|
||||
|
|
@ -2513,6 +2545,9 @@ static void build_image(const char *output,
|
|||
} else if (strcasecmp(info->id, "ARCHER-C6-V2-US") == 0) {
|
||||
const char mdat[11] = {0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x01, 0x01, 0x00};
|
||||
parts[5] = put_data("extra-para", mdat, 11);
|
||||
} else if (strcasecmp(info->id, "EAP245-V3") == 0) {
|
||||
const char mdat[10] = {0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x01, 0x01};
|
||||
parts[5] = put_data("extra-para", mdat, 10);
|
||||
}
|
||||
|
||||
size_t len;
|
||||
|
|
|
|||
Loading…
Reference in New Issue