uboot-mediatek: add Qihoo 360T7 support

The vendor uboot will verify firmware at boot.
So add a custom uboot build for this device.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit c51eb17730)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This commit is contained in:
Chukun Pan 2023-04-28 23:36:17 +08:00 committed by Daniel Golle
parent f588da89a3
commit 99c94c6696
4 changed files with 477 additions and 0 deletions

View File

@ -41,6 +41,7 @@ xiaomi,redmi-router-ax6000-stock)
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x10000" "0x20000"
ubootenv_add_uci_sys_config "/dev/mtd2" "0x0" "0x10000" "0x20000"
;;
qihoo,360t7|\
tplink,tl-xdr4288|\
tplink,tl-xdr6086|\
tplink,tl-xdr6088|\

View File

@ -176,6 +176,18 @@ define U-Boot/mt7629_rfb
UBOOT_CONFIG:=mt7629_rfb
endef
define U-Boot/mt7981_qihoo_360t7
NAME:=Qihoo 360T7
BUILD_SUBTARGET:=filogic
BUILD_DEVICES:=qihoo_360t7
UBOOT_CONFIG:=mt7981_qihoo-360t7
UBOOT_IMAGE:=u-boot.fip
BL2_BOOTDEV:=spim-nand
BL2_SOC:=mt7981
BL2_DDRTYPE:=ddr3
DEPENDS:=+trusted-firmware-a-mt7981-spim-nand-ddr3
endef
define U-Boot/mt7986_rfb
NAME:=MT7986 Reference Board
BUILD_SUBTARGET:=filogic
@ -301,6 +313,7 @@ UBOOT_TARGETS := \
mt7628_rfb \
ravpower_rp-wd009 \
mt7629_rfb \
mt7981_qihoo_360t7 \
mt7986_bananapi_bpi-r3-emmc \
mt7986_bananapi_bpi-r3-sdmmc \
mt7986_bananapi_bpi-r3-snand \

View File

@ -0,0 +1,43 @@
--- a/board/mediatek/mt7981/mt7981_rfb.c
+++ b/board/mediatek/mt7981/mt7981_rfb.c
@@ -6,9 +6,16 @@
#include <common.h>
#include <config.h>
+#include <dm.h>
+#include <button.h>
#include <env.h>
#include <init.h>
#include <asm/global_data.h>
+#include <linux/delay.h>
+
+#ifndef CONFIG_RESET_BUTTON_LABEL
+#define CONFIG_RESET_BUTTON_LABEL "reset"
+#endif
#include <mtd.h>
#include <linux/mtd/mtd.h>
@@ -24,7 +31,22 @@ int board_init(void)
int board_late_init(void)
{
- gd->env_valid = 1; //to load environment variable from persistent store
+ struct udevice *dev;
+
+ gd->env_valid = ENV_VALID;
+ if (!button_get_by_label(CONFIG_RESET_BUTTON_LABEL, &dev)) {
+ puts("reset button found\n");
+#ifdef CONFIG_RESET_BUTTON_SETTLE_DELAY
+ if (CONFIG_RESET_BUTTON_SETTLE_DELAY > 0) {
+ button_get_state(dev);
+ mdelay(CONFIG_RESET_BUTTON_SETTLE_DELAY);
+ }
+#endif
+ if (button_get_state(dev) == BUTTON_ON) {
+ puts("button pushed, resetting environment\n");
+ gd->env_valid = ENV_INVALID;
+ }
+ }
env_relocate();
return 0;
}

View File

@ -0,0 +1,420 @@
--- /dev/null
+++ b/configs/mt7981_qihoo-360t7_defconfig
@@ -0,0 +1,175 @@
+CONFIG_ARM=y
+CONFIG_POSITION_INDEPENDENT=y
+CONFIG_ARCH_MEDIATEK=y
+CONFIG_TARGET_MT7981=y
+CONFIG_TEXT_BASE=0x41e00000
+CONFIG_SYS_MALLOC_F_LEN=0x4000
+CONFIG_SYS_HAS_NONCACHED_MEMORY=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_DEFAULT_DEVICE_TREE="mt7981_qihoo-360t7"
+CONFIG_DEFAULT_ENV_FILE="qihoo-360t7_env"
+CONFIG_DEFAULT_FDT_FILE="mediatek/mt7981_qihoo-360t7.dtb"
+CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_DEBUG_UART_BASE=0x11002000
+CONFIG_DEBUG_UART_CLOCK=40000000
+CONFIG_DEBUG_UART=y
+CONFIG_SYS_LOAD_ADDR=0x46000000
+CONFIG_SMBIOS_PRODUCT_NAME=""
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_BOOTDELAY=30
+CONFIG_AUTOBOOT_MENU_SHOW=y
+CONFIG_CFB_CONSOLE_ANSI=y
+CONFIG_BOARD_LATE_INIT=y
+CONFIG_BUTTON=y
+CONFIG_BUTTON_GPIO=y
+CONFIG_GPIO_HOG=y
+CONFIG_CMD_ENV_FLAGS=y
+CONFIG_FIT=y
+CONFIG_FIT_ENABLE_SHA256_SUPPORT=y
+CONFIG_LED=y
+CONFIG_LED_BLINK=y
+CONFIG_LED_GPIO=y
+CONFIG_LOGLEVEL=7
+CONFIG_LOG=y
+CONFIG_SYS_PROMPT="MT7981> "
+CONFIG_CMD_BOOTMENU=y
+CONFIG_CMD_BOOTP=y
+CONFIG_CMD_BUTTON=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_CDP=y
+CONFIG_CMD_CPU=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_DNS=y
+CONFIG_CMD_ECHO=y
+CONFIG_CMD_ENV_READMEM=y
+CONFIG_CMD_ERASEENV=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FDT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_CMD_FS_UUID=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_HASH=y
+CONFIG_CMD_ITEST=y
+CONFIG_CMD_LED=y
+CONFIG_CMD_LICENSE=y
+CONFIG_CMD_LINK_LOCAL=y
+# CONFIG_CMD_MBR is not set
+CONFIG_CMD_PCI=y
+CONFIG_CMD_PSTORE=y
+CONFIG_CMD_PSTORE_MEM_ADDR=0x42ff0000
+CONFIG_CMD_SF_TEST=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_PXE=y
+CONFIG_CMD_PWM=y
+CONFIG_CMD_SMC=y
+CONFIG_CMD_TFTPBOOT=y
+CONFIG_CMD_TFTPSRV=y
+CONFIG_CMD_UBI=y
+CONFIG_CMD_UBI_RENAME=y
+CONFIG_CMD_UBIFS=y
+CONFIG_CMD_ASKENV=y
+CONFIG_CMD_PART=y
+CONFIG_CMD_RARP=y
+CONFIG_CMD_SETEXPR=y
+CONFIG_CMD_SLEEP=y
+CONFIG_CMD_SNTP=y
+CONFIG_CMD_SOURCE=y
+CONFIG_CMD_STRINGS=y
+CONFIG_CMD_UUID=y
+CONFIG_DISPLAY_CPUINFO=y
+CONFIG_DM_MTD=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_DM_PWM=y
+CONFIG_PWM_MTK=y
+CONFIG_HUSH_PARSER=y
+CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_VERSION_VARIABLE=y
+CONFIG_PARTITION_UUIDS=y
+CONFIG_NETCONSOLE=y
+CONFIG_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_CLK=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_SCSI=y
+CONFIG_AHCI=y
+CONFIG_AHCI_PCI=y
+CONFIG_SCSI_AHCI=y
+CONFIG_SCSI=y
+CONFIG_CMD_SCSI=y
+CONFIG_PHY=y
+CONFIG_PHY_MTK_TPHY=y
+CONFIG_PHY_FIXED=y
+CONFIG_MTK_AHCI=y
+CONFIG_DM_ETH=y
+CONFIG_MEDIATEK_ETH=y
+CONFIG_PCI=y
+# CONFIG_MMC is not set
+# CONFIG_DM_MMC is not set
+CONFIG_MTD=y
+CONFIG_MTD_UBI_FASTMAP=y
+CONFIG_DM_PCI=y
+CONFIG_PCIE_MEDIATEK=y
+CONFIG_PINCTRL=y
+CONFIG_PINCONF=y
+CONFIG_PINCTRL_MT7622=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_PRE_CONSOLE_BUFFER=y
+CONFIG_PRE_CON_BUF_ADDR=0x4007EF00
+CONFIG_MTK_POWER_DOMAIN=y
+CONFIG_RAM=y
+CONFIG_DM_SERIAL=y
+CONFIG_MTK_SERIAL=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_MTK_SPI_NAND=y
+CONFIG_MTK_SPI_NAND_MTD=y
+CONFIG_SYSRESET_WATCHDOG=y
+CONFIG_WDT_MTK=y
+CONFIG_LZO=y
+CONFIG_ZSTD=y
+CONFIG_HEXDUMP=y
+CONFIG_RANDOM_UUID=y
+CONFIG_REGEX=y
+CONFIG_OF_EMBED=y
+CONFIG_ENV_OVERWRITE=y
+CONFIG_ENV_IS_IN_UBI=y
+CONFIG_ENV_UBI_PART="ubi"
+CONFIG_ENV_SIZE=0x1f000
+CONFIG_ENV_SIZE_REDUND=0x1f000
+CONFIG_ENV_UBI_VOLUME="ubootenv"
+CONFIG_ENV_UBI_VOLUME_REDUND="ubootenv2"
+CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_CLK=y
+CONFIG_PHY_FIXED=y
+CONFIG_DM_ETH=y
+CONFIG_MEDIATEK_ETH=y
+CONFIG_PINCTRL=y
+CONFIG_PINCONF=y
+CONFIG_PINCTRL_MT7981=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_MTK_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_SERIAL=y
+CONFIG_MTK_SERIAL=y
+CONFIG_HEXDUMP=y
+CONFIG_USE_DEFAULT_ENV_FILE=y
+CONFIG_MTD_SPI_NAND=y
+CONFIG_MTK_SPIM=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_NAND=y
+CONFIG_CMD_NAND_TRIMFFS=y
+CONFIG_LMB_MAX_REGIONS=64
+CONFIG_USE_IPADDR=y
+CONFIG_IPADDR="192.168.1.1"
+CONFIG_USE_SERVERIP=y
+CONFIG_SERVERIP="192.168.1.254"
--- /dev/null
+++ b/arch/arm/dts/mt7981_qihoo-360t7.dts
@@ -0,0 +1,180 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2022 MediaTek Inc.
+ * Author: Sam Shih <sam.shih@mediatek.com>
+ */
+
+/dts-v1/;
+#include "mt7981.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ model = "Qihoo 360T7";
+ compatible = "mediatek,mt7981", "mediatek,mt7981-rfb";
+
+ chosen {
+ stdout-path = &uart0;
+ tick-timer = &timer0;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ factory {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ status_red {
+ label = "red:status";
+ gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+ };
+
+ status_green {
+ label = "green:status";
+ gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&uart0 {
+ mediatek,force-highspeed;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&eth {
+ status = "okay";
+ mediatek,gmac-id = <0>;
+ phy-mode = "sgmii";
+ mediatek,switch = "mt7531";
+ reset-gpios = <&gpio 39 GPIO_ACTIVE_HIGH>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&pinctrl {
+ spi_flash_pins: spi0-pins-func-1 {
+ mux {
+ function = "flash";
+ groups = "spi0", "spi0_wp_hold";
+ };
+
+ conf-pu {
+ pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_00>;
+ };
+
+ conf-pd {
+ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_00>;
+ };
+ };
+
+ spic_pins: spi1-pins-func-1 {
+ mux {
+ function = "spi";
+ groups = "spi1_1";
+ };
+ };
+
+ uart1_pins: spi1-pins-func-3 {
+ mux {
+ function = "uart";
+ groups = "uart1_2";
+ };
+ };
+
+ pwm_pins: pwm0-pins-func-1 {
+ mux {
+ function = "pwm";
+ groups = "pwm0_1", "pwm1_0";
+ };
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm_pins>;
+ status = "okay";
+};
+
+&spi0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_flash_pins>;
+ status = "okay";
+ must_tx;
+ enhance_timing;
+ dma_ext;
+ ipm_design;
+ support_quad;
+ tick_dly = <2>;
+ sample_sel = <0>;
+
+ spi_nand@0 {
+ compatible = "spi-nand";
+ reg = <0>;
+ spi-max-frequency = <52000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "bl2";
+ reg = <0x0 0x100000>;
+ };
+
+ partition@100000 {
+ label = "orig-env";
+ reg = <0x100000 0x80000>;
+ };
+
+ partition@160000 {
+ label = "factory";
+ reg = <0x180000 0x200000>;
+ };
+
+ partition@380000 {
+ label = "fip";
+ reg = <0x380000 0x200000>;
+ };
+
+ partition@580000 {
+ label = "ubi";
+ reg = <0x580000 0x6c00000>;
+ };
+ };
+ };
+};
+
+&watchdog {
+ status = "disabled";
+};
--- /dev/null
+++ b/qihoo-360t7_env
@@ -0,0 +1,56 @@
+ipaddr=192.168.1.1
+serverip=192.168.1.254
+loadaddr=0x46000000
+console=earlycon=uart8250,mmio32,0x11002000 console=ttyS0
+bootcmd=if pstore check ; then run boot_recovery ; else run boot_ubi ; fi
+bootconf=config-1
+bootdelay=0
+bootfile=openwrt-mediatek-filogic-qihoo_360t7-initramfs-recovery.itb
+bootfile_bl2=openwrt-mediatek-filogic-qihoo_360t7-preloader.bin
+bootfile_fip=openwrt-mediatek-filogic-qihoo_360t7-bl31-uboot.fip
+bootfile_upg=openwrt-mediatek-filogic-qihoo_360t7-squashfs-sysupgrade.itb
+bootled_pwr=green:status
+bootled_rec=red:status
+bootmenu_confirm_return=askenv - Press ENTER to return to menu ; bootmenu 60
+bootmenu_default=0
+bootmenu_delay=0
+bootmenu_title= ( ( ( OpenWrt ) ) )
+bootmenu_0=Initialize environment.=run _firstboot
+bootmenu_0d=Run default boot command.=run boot_default
+bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return
+bootmenu_2=Boot production system from NAND.=run boot_production ; run bootmenu_confirm_return
+bootmenu_3=Boot recovery system from NAND.=run boot_recovery ; run bootmenu_confirm_return
+bootmenu_4=Load production system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
+bootmenu_5=Load recovery system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
+bootmenu_6=Load BL31+U-Boot FIP via TFTP then write to NAND.=run boot_tftp_write_fip ; run bootmenu_confirm_return
+bootmenu_7=Load BL2 preloader via TFTP then write to NAND.=run boot_tftp_write_bl2 ; run bootmenu_confirm_return
+bootmenu_8=Reboot.=reset
+bootmenu_9=Reset all settings to factory defaults.=run reset_factory ; reset
+boot_first=if button reset ; then led $bootled_rec on ; run boot_tftp_recovery ; setenv flag_recover 1 ; run boot_default ; fi ; bootmenu
+boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever
+boot_production=led $bootled_pwr on ; run ubi_read_production && bootm $loadaddr#$bootconf ; led $bootled_pwr off
+boot_recovery=led $bootled_rec on ; run ubi_read_recovery && bootm $loadaddr#$bootconf ; led $bootled_rec off
+boot_ubi=run boot_production ; run boot_recovery ; run boot_tftp_forever
+boot_tftp_forever=led $bootled_rec on ; while true ; do run boot_tftp_recovery ; sleep 1 ; done
+boot_tftp_production=tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run ubi_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
+boot_tftp_recovery=tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run ubi_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
+boot_tftp=tftpboot $loadaddr $bootfile && bootm $loadaddr#$bootconf
+boot_tftp_write_fip=tftpboot $loadaddr $bootfile_fip && run mtd_write_fip && run reset_factory
+boot_tftp_write_bl2=tftpboot $loadaddr $bootfile_bl2 && run mtd_write_bl2
+part_default=production
+part_recovery=recovery
+reset_factory=ubi part ubi ; mw $loadaddr 0x0 0x800 ; ubi write $loadaddr ubootenv 0x800 ; ubi write $loadaddr ubootenv2 0x800
+mtd_write_fip=mtd erase fip && mtd write fip $loadaddr
+mtd_write_bl2=mtd erase bl2 && mtd write bl2 $loadaddr
+ubi_create_env=ubi check ubootenv || ubi create ubootenv 0x100000 dynamic 0 || run ubi_format ; ubi check ubootenv2 || ubi create ubootenv2 0x100000 dynamic 1 || run ubi_format
+ubi_format=ubi detach ; mtd erase ubi && ubi part ubi ; reset
+ubi_prepare_rootfs=if ubi check rootfs_data ; then else if env exists rootfs_data_max ; then ubi create rootfs_data $rootfs_data_max dynamic || ubi create rootfs_data - dynamic ; else ubi create rootfs_data - dynamic ; fi ; fi
+ubi_read_production=ubi read $loadaddr fit && iminfo $loadaddr && run ubi_prepare_rootfs
+ubi_read_recovery=ubi check recovery && ubi read $loadaddr recovery
+ubi_remove_rootfs=ubi check rootfs_data && ubi remove rootfs_data
+ubi_write_production=ubi check fit && ubi remove fit ; run ubi_remove_rootfs ; ubi create fit $filesize dynamic 2 && ubi write $loadaddr fit $filesize
+ubi_write_recovery=ubi check recovery && ubi remove recovery ; run ubi_remove_rootfs ; ubi create recovery $filesize dynamic 3 && ubi write $loadaddr recovery $filesize
+_init_env=setenv _init_env ; run ubi_create_env ; saveenv ; saveenv
+_firstboot=setenv _firstboot ; run _switch_to_menu ; run _init_env ; run boot_first
+_switch_to_menu=setenv _switch_to_menu ; setenv bootdelay 3 ; setenv bootmenu_delay 3 ; setenv bootmenu_0 $bootmenu_0d ; setenv bootmenu_0d ; run _bootmenu_update_title
+_bootmenu_update_title=setenv _bootmenu_update_title ; setenv bootmenu_title "$bootmenu_title $ver"