ath79: add support for Atheros DB120 reference board
Atheros DB120 reference board.
Specifications:
SoC: QCA9344
DRAM: 128Mb DDR2
Flash: 8Mb SPI-NOR, 128Mb NAND flash
Switch: 5x 10/100Mbps via AR8229 switch (integrated into SoC),
5x 10/100/1000Mbps via QCA8237 via RGMII
WLAN: AR9300 (SoC, 2.4G+5G) + AR9340 (PCIe, 5G-only)
USB: 1x 2.0
UART: standard QCA UART header
JTAG: yes
Button: 1x reset
LEDs: a lot
Slots: 2x mPCIe + 1x mini-PCI, but using them requires
additional undocumented changes.
Misc: The board allows to boot off NAND, and there is
I2S audio support as well - also requiring
additional undocumented changes.
Installation:
1. Original bootloader
Connect the board to ethernet
Set up a server with an IP address of 192.168.1.10
Make the openwrt-ath79-generic-atheros_db120-squashfs-factory.bin
available via TFTP
tftpboot 0x80060000 openwrt-ath79-generic-atheros_db120-squashfs-factory.bin
erase 0x9f050000 +$filesize
cp.b $fileaddr 0x9f050000 $filesize
2. pepe2k's u-boot_mod
Connect the board to ethernet
Set up a server with an IP address of 192.168.1.10
Make the openwrt-ath79-generic-atheros_db120-squashfs-factory.bin
available via TFTP, as "firmware.bin"
run fw_upg
Reboot the board.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
[explicit factory recipe in generic.mk, sorting in 10-ath9k-eeprom,
convert to nvmem, use fwconcat* names in DTS, remove unneeded DT
labels, remove redundant uart node]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit is contained in:
Zoltan HERPAI
parent
61b49cd3f8
commit
98eb95dd00
|
|
@ -0,0 +1,250 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "ar9344.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/mtd/partitions/uimage.h>
|
||||
|
||||
/ {
|
||||
model = "Atheros DB120 reference board";
|
||||
compatible = "atheros,db120", "qca,ar9344";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_system;
|
||||
led-failsafe = &led_system;
|
||||
led-running = &led_system;
|
||||
led-upgrade = &led_system;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
wlan2g {
|
||||
label = "green:wlan2g";
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
label = "green:wlan5g";
|
||||
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
|
||||
led_system: system {
|
||||
label = "green:system";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
usb {
|
||||
label = "green:usb";
|
||||
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
||||
trigger-sources = <&hub_port1>;
|
||||
linux,default-trigger = "usbport";
|
||||
};
|
||||
};
|
||||
|
||||
leds-ath9k {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
wlan5g-ath {
|
||||
label = "green:wlan5g-ath";
|
||||
gpios = <&ath9k 0 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
wps {
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
label = "WPS button";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
virtual_flash {
|
||||
compatible = "mtd-concat";
|
||||
devices = <&fwconcat0 &fwconcat1>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
reg = <0x0 0x0>;
|
||||
label = "firmware";
|
||||
compatible = "openwrt,uimage", "denx,uimage";
|
||||
openwrt,ih-magic = <IH_MAGIC_OKLI>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&ref {
|
||||
clock-frequency = <40000000>;
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
uboot: partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x040000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
fwconcat0: partition@50000 {
|
||||
label = "fwconcat0";
|
||||
reg = <0x050000 0x630000>;
|
||||
};
|
||||
|
||||
partition@680000 {
|
||||
label = "loader";
|
||||
reg = <0x680000 0x010000>;
|
||||
};
|
||||
|
||||
fwconcat1: partition@690000 {
|
||||
label = "fwconcat1";
|
||||
reg = <0x690000 0x150000>;
|
||||
};
|
||||
|
||||
partition@7e0000 {
|
||||
label = "nvram";
|
||||
reg = <0x7e0000 0x010000>;
|
||||
};
|
||||
|
||||
art: partition@7f0000 {
|
||||
label = "art";
|
||||
reg = <0x7f0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
pll-data = <0x06000000 0x00000101 0x00001616>;
|
||||
|
||||
nvmem-cells = <&macaddr_art_0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
|
||||
phy-mode = "rgmii";
|
||||
phy-handle = <&phy0>;
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
phy-mask = <0>;
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
|
||||
qca,ar8327-initvals = <
|
||||
0x04 0x07600000 /* PORT0 PAD MODE CTRL */
|
||||
0x10 0xc1000000 /* POWER_ON_STRAP */
|
||||
0x7c 0x0000007e /* PORT0_STATUS */
|
||||
0x94 0x0000007e /* PORT6_STATUS */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
&pinmux {
|
||||
pmx_led_wan_lan: pinmux_led_wan_lan {
|
||||
pinctrl-single,bits = <0x10 0x2c2d0000 0xffff0000>,
|
||||
<0x14 0x292a2b 0xffffff>;
|
||||
};
|
||||
};
|
||||
|
||||
&builtin_switch {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmx_led_wan_lan>;
|
||||
|
||||
/delete-property/qca,phy4-mii-enable;
|
||||
};
|
||||
|
||||
ð1 {
|
||||
status = "okay";
|
||||
|
||||
nvmem-cells = <&macaddr_art_6>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
|
||||
gmac-config {
|
||||
device = <&gmac>;
|
||||
switch-phy-swap = <0>;
|
||||
switch-only-mode = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
|
||||
ath9k: wifi@0,0 {
|
||||
compatible = "pci168c,0030";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
qca,no-eeprom;
|
||||
qca,disable-2ghz;
|
||||
#gpio-cells = <2>;
|
||||
gpio-controller;
|
||||
};
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
mtd-cal-data = <&art 0x1000>;
|
||||
};
|
||||
|
||||
&usb {
|
||||
status = "okay";
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
hub_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&art {
|
||||
compatible = "nvmem-cells";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_art_0: macaddr@0 {
|
||||
reg = <0x0 0x6>;
|
||||
};
|
||||
|
||||
macaddr_art_6: macaddr@6 {
|
||||
reg = <0x6 0x6>;
|
||||
};
|
||||
};
|
||||
|
|
@ -116,6 +116,12 @@ ath79_setup_interfaces()
|
|||
ubnt,unifi-ap-outdoor-plus)
|
||||
ucidef_set_interface_lan "eth0 eth1"
|
||||
;;
|
||||
atheros,db120)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "2:lan" "3:lan" "4:lan" "5:lan" "1:wan"
|
||||
ucidef_add_switch "switch1" \
|
||||
"0@eth1" "1:lan" "2:lan" "3:lan" "4:lan" "5:lan"
|
||||
;;
|
||||
avm,fritz4020|\
|
||||
pcs,cr3000|\
|
||||
tplink,archer-c58-v1|\
|
||||
|
|
|
|||
|
|
@ -72,6 +72,21 @@ case "$FIRMWARE" in
|
|||
;;
|
||||
"ath9k-eeprom-pci-0000:00:00.0.bin")
|
||||
case $board in
|
||||
atheros,db120|\
|
||||
engenius,eap600|\
|
||||
engenius,ecb600|\
|
||||
mercury,mw4530r-v1|\
|
||||
ocedo,raccoon|\
|
||||
tplink,tl-wdr3500-v1|\
|
||||
tplink,tl-wdr3600-v1|\
|
||||
tplink,tl-wdr4300-v1|\
|
||||
tplink,tl-wdr4300-v1-il|\
|
||||
tplink,tl-wdr4310-v1|\
|
||||
tplink,tl-wdr4900-v2|\
|
||||
ubnt,unifi-ap-pro|\
|
||||
winchannel,wb2000)
|
||||
caldata_extract "art" 0x5000 0x440
|
||||
;;
|
||||
avm,fritz300e)
|
||||
caldata_extract_reverse "urloader" 0x1541 0x440
|
||||
;;
|
||||
|
|
@ -88,20 +103,6 @@ case "$FIRMWARE" in
|
|||
caldata_extract "art" 0x5000 0x440
|
||||
ath9k_patch_mac $(macaddr_add $(mtd_get_mac_text "mac" 0x18) 1)
|
||||
;;
|
||||
engenius,eap600|\
|
||||
engenius,ecb600|\
|
||||
mercury,mw4530r-v1|\
|
||||
ocedo,raccoon|\
|
||||
tplink,tl-wdr3500-v1|\
|
||||
tplink,tl-wdr3600-v1|\
|
||||
tplink,tl-wdr4300-v1|\
|
||||
tplink,tl-wdr4300-v1-il|\
|
||||
tplink,tl-wdr4310-v1|\
|
||||
tplink,tl-wdr4900-v2|\
|
||||
ubnt,unifi-ap-pro|\
|
||||
winchannel,wb2000)
|
||||
caldata_extract "art" 0x5000 0x440
|
||||
;;
|
||||
enterasys,ws-ap3705i)
|
||||
caldata_extract "calibrate" 0x5000 0x440
|
||||
ath9k_patch_mac $(mtd_get_mac_ascii u-boot-env0 RADIOADDR0)
|
||||
|
|
|
|||
|
|
@ -330,6 +330,27 @@ define Device/aruba_ap-105
|
|||
endef
|
||||
TARGET_DEVICES += aruba_ap-105
|
||||
|
||||
define Device/atheros_db120
|
||||
SOC := ar9344
|
||||
DEVICE_VENDOR := Atheros
|
||||
DEVICE_MODEL := DB120
|
||||
DEVICE_PACKAGES := kmod-usb2
|
||||
IMAGE_SIZE := 7808k
|
||||
SUPPORTED_DEVICES += db120
|
||||
LOADER_TYPE := bin
|
||||
LOADER_FLASH_OFFS := 0x50000
|
||||
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
|
||||
COMPILE := loader-$(1).bin loader-$(1).uImage
|
||||
COMPILE/loader-$(1).bin := loader-okli-compile
|
||||
COMPILE/loader-$(1).uImage := append-loader-okli $(1) | pad-to 64k | lzma | \
|
||||
uImage lzma
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
||||
append-rootfs | pad-rootfs | check-size | pad-to 6336k | \
|
||||
append-loader-okli-uimage $(1) | pad-to 64k
|
||||
endef
|
||||
TARGET_DEVICES += atheros_db120
|
||||
|
||||
define Device/avm
|
||||
DEVICE_VENDOR := AVM
|
||||
KERNEL := kernel-bin | append-dtb | lzma | eva-image
|
||||
|
|
|
|||
Loading…
Reference in New Issue