kirkwood: add support for ipTIME NAS1
ipTIME NAS1 is a 1-bay NAS, based on Marvell Kirkwood SoC. Specifications: * SoC: 88F6281 * RAM: 256 MiB * Flash: SPI NOR 16 MiB * SATA: 1x 3Gb/s * Ethernet: 1x 1GbE * USB: 1x 2.0 * Fan: 2 speed level * UART: JP1 (115200 8N1) * Pinout: [3V3] (TXD) (RXD) (GND) Notes: * There are several variants of the model name: "NAS-I", "NASI", "NAS1". Here "NAS1" is adopted for consistent naming scheme. * The reset button is also a USB copy button in stock FW, but in this patch the former is the only default behavior. Installation via web interface: 1. Flash sysupgrade image through the stock web interface. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This commit is contained in:
parent
0c568d044f
commit
957f9adeb1
|
@ -295,6 +295,11 @@ define Build/install-dtb
|
||||||
)
|
)
|
||||||
endef
|
endef
|
||||||
|
|
||||||
|
define Build/iptime-naspkg
|
||||||
|
$(STAGING_DIR_HOST)/bin/iptime-naspkg $(1) $@ $@.new
|
||||||
|
mv $@.new $@
|
||||||
|
endef
|
||||||
|
|
||||||
define Build/jffs2
|
define Build/jffs2
|
||||||
rm -rf $(KDIR_TMP)/$(DEVICE_NAME)/jffs2 && \
|
rm -rf $(KDIR_TMP)/$(DEVICE_NAME)/jffs2 && \
|
||||||
mkdir -p $(KDIR_TMP)/$(DEVICE_NAME)/jffs2/$$(dirname $(1)) && \
|
mkdir -p $(KDIR_TMP)/$(DEVICE_NAME)/jffs2/$$(dirname $(1)) && \
|
||||||
|
|
|
@ -22,6 +22,7 @@ kirkwood_setup_interfaces()
|
||||||
globalscale,sheevaplug|\
|
globalscale,sheevaplug|\
|
||||||
iom,iconnect-1.1|\
|
iom,iconnect-1.1|\
|
||||||
iom,ix2-200|\
|
iom,ix2-200|\
|
||||||
|
iptime,nas1|\
|
||||||
netgear,readynas-duo-v2|\
|
netgear,readynas-duo-v2|\
|
||||||
raidsonic,ib-nas62x0|\
|
raidsonic,ib-nas62x0|\
|
||||||
seagate,blackarmor-nas220|\
|
seagate,blackarmor-nas220|\
|
||||||
|
@ -55,6 +56,10 @@ kirkwood_setup_macs()
|
||||||
local label_mac=""
|
local label_mac=""
|
||||||
|
|
||||||
case "$board" in
|
case "$board" in
|
||||||
|
iptime,nas1)
|
||||||
|
lan_mac=$(mtd_get_mac_binary u-boot 0x3ffa8)
|
||||||
|
label_mac=$lan_mac
|
||||||
|
;;
|
||||||
linksys,e4200-v2|\
|
linksys,e4200-v2|\
|
||||||
linksys,ea3500|\
|
linksys,ea3500|\
|
||||||
linksys,ea4500)
|
linksys,ea4500)
|
||||||
|
|
|
@ -27,6 +27,10 @@ preinit_set_mac_address() {
|
||||||
ip link set dev port3 address $(macaddr_add $mac 2) 2>/dev/null
|
ip link set dev port3 address $(macaddr_add $mac 2) 2>/dev/null
|
||||||
ip link set dev port4 address $(macaddr_add $mac 3) 2>/dev/null
|
ip link set dev port4 address $(macaddr_add $mac 3) 2>/dev/null
|
||||||
;;
|
;;
|
||||||
|
iptime,nas1)
|
||||||
|
mac=$(mtd_get_mac_binary u-boot 0x3ffa8)
|
||||||
|
ip link set dev eth0 address $mac 2>/dev/null
|
||||||
|
;;
|
||||||
esac
|
esac
|
||||||
}
|
}
|
||||||
|
|
||||||
|
|
|
@ -1,6 +1,7 @@
|
||||||
RAMFS_COPY_BIN='fw_printenv fw_setenv strings'
|
RAMFS_COPY_BIN='fw_printenv fw_setenv strings'
|
||||||
RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
|
RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
|
||||||
|
|
||||||
|
PART_NAME=firmware
|
||||||
REQUIRE_IMAGE_METADATA=1
|
REQUIRE_IMAGE_METADATA=1
|
||||||
|
|
||||||
platform_check_image() {
|
platform_check_image() {
|
||||||
|
@ -33,6 +34,9 @@ platform_do_upgrade() {
|
||||||
return 1
|
return 1
|
||||||
fi
|
fi
|
||||||
;;
|
;;
|
||||||
|
iptime,nas1)
|
||||||
|
default_do_upgrade "$1"
|
||||||
|
;;
|
||||||
linksys,e4200-v2|\
|
linksys,e4200-v2|\
|
||||||
linksys,ea3500|\
|
linksys,ea3500|\
|
||||||
linksys,ea4500)
|
linksys,ea4500)
|
||||||
|
|
|
@ -122,6 +122,7 @@ CONFIG_HARDIRQS_SW_RESEND=y
|
||||||
CONFIG_HAS_DMA=y
|
CONFIG_HAS_DMA=y
|
||||||
CONFIG_HAS_IOMEM=y
|
CONFIG_HAS_IOMEM=y
|
||||||
CONFIG_HAS_IOPORT_MAP=y
|
CONFIG_HAS_IOPORT_MAP=y
|
||||||
|
CONFIG_HWMON=y
|
||||||
CONFIG_HW_RANDOM=y
|
CONFIG_HW_RANDOM=y
|
||||||
CONFIG_HW_RANDOM_OMAP=y
|
CONFIG_HW_RANDOM_OMAP=y
|
||||||
CONFIG_HZ_FIXED=0
|
CONFIG_HZ_FIXED=0
|
||||||
|
@ -163,6 +164,9 @@ CONFIG_MTD_NAND_ECC_SW_HAMMING=y
|
||||||
# CONFIG_MTD_NAND_MARVELL is not set
|
# CONFIG_MTD_NAND_MARVELL is not set
|
||||||
CONFIG_MTD_NAND_ORION=y
|
CONFIG_MTD_NAND_ORION=y
|
||||||
CONFIG_MTD_RAW_NAND=y
|
CONFIG_MTD_RAW_NAND=y
|
||||||
|
CONFIG_MTD_SPI_NOR=y
|
||||||
|
CONFIG_MTD_SPLIT_FIRMWARE=y
|
||||||
|
CONFIG_MTD_SPLIT_UIMAGE_FW=y
|
||||||
CONFIG_MTD_UBI=y
|
CONFIG_MTD_UBI=y
|
||||||
CONFIG_MTD_UBI_BEB_LIMIT=20
|
CONFIG_MTD_UBI_BEB_LIMIT=20
|
||||||
CONFIG_MTD_UBI_BLOCK=y
|
CONFIG_MTD_UBI_BLOCK=y
|
||||||
|
@ -248,6 +252,7 @@ CONFIG_SPARSE_IRQ=y
|
||||||
CONFIG_SPI=y
|
CONFIG_SPI=y
|
||||||
# CONFIG_SPI_ARMADA_3700 is not set
|
# CONFIG_SPI_ARMADA_3700 is not set
|
||||||
CONFIG_SPI_MASTER=y
|
CONFIG_SPI_MASTER=y
|
||||||
|
CONFIG_SPI_MEM=y
|
||||||
CONFIG_SPI_ORION=y
|
CONFIG_SPI_ORION=y
|
||||||
CONFIG_SPLIT_PTLOCK_CPUS=999999
|
CONFIG_SPLIT_PTLOCK_CPUS=999999
|
||||||
CONFIG_SRAM=y
|
CONFIG_SRAM=y
|
||||||
|
@ -259,6 +264,7 @@ CONFIG_THERMAL=y
|
||||||
CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
|
CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
|
||||||
CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0
|
CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0
|
||||||
CONFIG_THERMAL_GOV_STEP_WISE=y
|
CONFIG_THERMAL_GOV_STEP_WISE=y
|
||||||
|
CONFIG_THERMAL_HWMON=y
|
||||||
CONFIG_THERMAL_OF=y
|
CONFIG_THERMAL_OF=y
|
||||||
CONFIG_TICK_CPU_ACCOUNTING=y
|
CONFIG_TICK_CPU_ACCOUNTING=y
|
||||||
CONFIG_TIMER_OF=y
|
CONFIG_TIMER_OF=y
|
||||||
|
|
|
@ -0,0 +1,231 @@
|
||||||
|
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||||
|
/dts-v1/;
|
||||||
|
|
||||||
|
#include "kirkwood.dtsi"
|
||||||
|
#include "kirkwood-6281.dtsi"
|
||||||
|
|
||||||
|
/ {
|
||||||
|
model = "ipTIME NAS1";
|
||||||
|
compatible = "iptime,nas1", "marvell,kirkwood-88f6281", "marvell,kirkwood";
|
||||||
|
|
||||||
|
aliases {
|
||||||
|
serial0 = &uart0;
|
||||||
|
led-boot = &led_ready;
|
||||||
|
led-failsafe = &led_ready;
|
||||||
|
led-running = &led_ready;
|
||||||
|
led-upgrade = &led_ready;
|
||||||
|
};
|
||||||
|
|
||||||
|
chosen {
|
||||||
|
/*
|
||||||
|
* "root" argument from the stock bootloader should be ignored
|
||||||
|
* as it'll prevent the kernel from finding the correct rootfs.
|
||||||
|
*/
|
||||||
|
bootargs-append = " console=ttyS0,115200 root=";
|
||||||
|
stdout-path = "serial0:115200n8";
|
||||||
|
};
|
||||||
|
|
||||||
|
memory@0 {
|
||||||
|
device_type = "memory";
|
||||||
|
reg = <0x00000000 0x10000000>;
|
||||||
|
};
|
||||||
|
|
||||||
|
gpio-leds {
|
||||||
|
compatible = "gpio-leds";
|
||||||
|
|
||||||
|
pinctrl-0 = <&pmx_led>;
|
||||||
|
pinctrl-names = "default";
|
||||||
|
|
||||||
|
hdd {
|
||||||
|
label = "blue:hdd";
|
||||||
|
gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
|
||||||
|
linux,default-trigger = "ata1";
|
||||||
|
};
|
||||||
|
|
||||||
|
usb {
|
||||||
|
label = "blue:usb";
|
||||||
|
gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
|
||||||
|
trigger-sources = <&ehci_port1>;
|
||||||
|
linux,default-trigger = "usbport";
|
||||||
|
};
|
||||||
|
|
||||||
|
led_ready: ready {
|
||||||
|
label = "blue:ready";
|
||||||
|
gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
gpio-keys {
|
||||||
|
compatible = "gpio-keys";
|
||||||
|
|
||||||
|
pinctrl-0 = <&pmx_button>;
|
||||||
|
pinctrl-names = "default";
|
||||||
|
|
||||||
|
reset-copy {
|
||||||
|
label = "Reset/Copy Button";
|
||||||
|
linux,code = <KEY_RESTART>;
|
||||||
|
gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
|
||||||
|
};
|
||||||
|
|
||||||
|
power {
|
||||||
|
label = "Power Button";
|
||||||
|
linux,code = <KEY_POWER>;
|
||||||
|
gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
gpio-fan {
|
||||||
|
compatible = "gpio-fan";
|
||||||
|
|
||||||
|
pinctrl-0 = <&pmx_fan>;
|
||||||
|
pinctrl-names = "default";
|
||||||
|
gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>,
|
||||||
|
<&gpio1 10 GPIO_ACTIVE_HIGH>;
|
||||||
|
/* We don't know the exact rpm, just use dummy values here. */
|
||||||
|
gpio-fan,speed-map = <0 0>, <1 1>, <2 2>;
|
||||||
|
#cooling-cells = <2>;
|
||||||
|
};
|
||||||
|
|
||||||
|
gpio-poweroff {
|
||||||
|
compatible = "gpio-poweroff";
|
||||||
|
gpios = <&pca9536 0 GPIO_ACTIVE_LOW>;
|
||||||
|
};
|
||||||
|
|
||||||
|
regulators {
|
||||||
|
compatible = "simple-bus";
|
||||||
|
#address-cells = <1>;
|
||||||
|
#size-cells = <0>;
|
||||||
|
|
||||||
|
pinctrl-0 = <&pmx_usb_vbus>;
|
||||||
|
pinctrl-names = "default";
|
||||||
|
|
||||||
|
regulator@1 {
|
||||||
|
compatible = "regulator-fixed";
|
||||||
|
reg = <1>;
|
||||||
|
regulator-name = "USB Power";
|
||||||
|
regulator-min-microvolt = <5000000>;
|
||||||
|
regulator-max-microvolt = <5000000>;
|
||||||
|
enable-active-high;
|
||||||
|
regulator-always-on;
|
||||||
|
gpio = <&gpio1 11 GPIO_ACTIVE_HIGH>;
|
||||||
|
};
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
&pinctrl {
|
||||||
|
pmx_led: pmx-led {
|
||||||
|
marvell,pins = "mpp35", "mpp45", "mpp46";
|
||||||
|
marvell,function = "gpio";
|
||||||
|
};
|
||||||
|
|
||||||
|
pmx_fan: pmx-fan {
|
||||||
|
marvell,pins = "mpp41", "mpp42";
|
||||||
|
marvell,function = "gpio";
|
||||||
|
};
|
||||||
|
|
||||||
|
pmx_usb_vbus: pmx-usb-vbus {
|
||||||
|
marvell,pins = "mpp43";
|
||||||
|
marvell,function = "gpio";
|
||||||
|
};
|
||||||
|
|
||||||
|
pmx_button: pmx-button {
|
||||||
|
marvell,pins = "mpp44", "mpp48";
|
||||||
|
marvell,function = "gpio";
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
&spi0 {
|
||||||
|
status = "okay";
|
||||||
|
|
||||||
|
flash@0 {
|
||||||
|
compatible = "jedec,spi-nor";
|
||||||
|
reg = <0>;
|
||||||
|
spi-max-frequency = <20000000>;
|
||||||
|
|
||||||
|
partitions {
|
||||||
|
compatible = "fixed-partitions";
|
||||||
|
#address-cells = <1>;
|
||||||
|
#size-cells = <1>;
|
||||||
|
|
||||||
|
partition@0 {
|
||||||
|
label = "u-boot";
|
||||||
|
reg = <0x0 0x40000>;
|
||||||
|
read-only;
|
||||||
|
};
|
||||||
|
|
||||||
|
partition@40000 {
|
||||||
|
compatible = "openwrt,uimage", "denx,uimage";
|
||||||
|
openwrt,offset = <0x400>;
|
||||||
|
label = "firmware";
|
||||||
|
reg = <0x40000 0xf80000>;
|
||||||
|
};
|
||||||
|
|
||||||
|
partition@fc0000 {
|
||||||
|
label = "config";
|
||||||
|
reg = <0xfc0000 0x40000>;
|
||||||
|
read-only;
|
||||||
|
};
|
||||||
|
};
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
&rtc {
|
||||||
|
status = "disabled";
|
||||||
|
};
|
||||||
|
|
||||||
|
&i2c0 {
|
||||||
|
status = "okay";
|
||||||
|
|
||||||
|
pca9536: gpio@41 {
|
||||||
|
compatible = "nxp,pca9536";
|
||||||
|
reg = <0x41>;
|
||||||
|
gpio-controller;
|
||||||
|
#gpio-cells = <2>;
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
&uart0 {
|
||||||
|
status = "okay";
|
||||||
|
};
|
||||||
|
|
||||||
|
&usb0 {
|
||||||
|
status = "okay";
|
||||||
|
|
||||||
|
#address-cells = <1>;
|
||||||
|
#size-cells = <0>;
|
||||||
|
|
||||||
|
ehci_port1: port@1 {
|
||||||
|
reg = <1>;
|
||||||
|
#trigger-source-cells = <0>;
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
&mdio {
|
||||||
|
status = "okay";
|
||||||
|
|
||||||
|
ethphyb: ethernet-phy@b {
|
||||||
|
reg = <0x0b>;
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
ð1 {
|
||||||
|
status = "okay";
|
||||||
|
};
|
||||||
|
|
||||||
|
ð1port {
|
||||||
|
phy-handle = <ðphyb>;
|
||||||
|
phy-connection-type = "rgmii-id";
|
||||||
|
};
|
||||||
|
|
||||||
|
&sata {
|
||||||
|
status = "okay";
|
||||||
|
|
||||||
|
#address-cells = <1>;
|
||||||
|
#size-cells = <0>;
|
||||||
|
nr-ports = <1>;
|
||||||
|
|
||||||
|
sata-port@0 {
|
||||||
|
reg = <0>;
|
||||||
|
#thermal-sensor-cells = <0>;
|
||||||
|
};
|
||||||
|
};
|
|
@ -184,6 +184,21 @@ define Device/iom_ix2-200
|
||||||
endef
|
endef
|
||||||
TARGET_DEVICES += iom_ix2-200
|
TARGET_DEVICES += iom_ix2-200
|
||||||
|
|
||||||
|
define Device/iptime_nas1
|
||||||
|
DEVICE_VENDOR := ipTIME
|
||||||
|
DEVICE_MODEL := NAS1
|
||||||
|
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 \
|
||||||
|
kmod-gpio-button-hotplug kmod-gpio-pca953x kmod-hwmon-drivetemp \
|
||||||
|
kmod-hwmon-gpiofan kmod-usb-ledtrig-usbport -uboot-envtools
|
||||||
|
KERNEL := $$(KERNEL) | iptime-naspkg nas1
|
||||||
|
BLOCKSIZE := 256k
|
||||||
|
IMAGE_SIZE := 15872k
|
||||||
|
IMAGES := sysupgrade.bin
|
||||||
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
||||||
|
check-size | append-metadata
|
||||||
|
endef
|
||||||
|
TARGET_DEVICES += iptime_nas1
|
||||||
|
|
||||||
define Device/linksys
|
define Device/linksys
|
||||||
DEVICE_VENDOR := Linksys
|
DEVICE_VENDOR := Linksys
|
||||||
DEVICE_PACKAGES := kmod-mwl8k wpad-basic-wolfssl kmod-gpio-button-hotplug
|
DEVICE_PACKAGES := kmod-mwl8k wpad-basic-wolfssl kmod-gpio-button-hotplug
|
||||||
|
|
Loading…
Reference in New Issue