ipq40xx: add MikroTik LHGG-60ad outdoor 802.11ad (60GHz) dish

LHGG-60ad is IPQ4019 + wil6210 based.

Specification:

- Qualcomm IPQ4019 (717 MHz)
- 256 MB of RAM (DDR3L)
- 16 MB (SPI NOR) of flash
- 1x Gbit ethernet, 802.3af/at POE IN connected through AR8035.
- WLAN: wil6210 802.11ad PCI card
- No USB or SD card ports
- UART disabled
- 8x LEDs

Biggest news is the wil6210 PCI card.
Integration for its configuration and detection has already been taken
care of when adding support for TP-Link Talon AD7200.
However, signal quality is much lower than with stock firmware, so
probably additional board-specific data has to be provided to the
driver and is still missing at the moment.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[Fix Ethernet Interface]
Signed-off-by: Nick Hainke <vincent@systemli.org>
This commit is contained in:
Alexander Couzens 2021-01-05 00:22:00 +01:00 committed by Daniel Golle
parent ab241e0937
commit 8d62304785
No known key found for this signature in database
GPG Key ID: 5A8F39C31C3217CA
7 changed files with 286 additions and 3 deletions

View File

@ -22,7 +22,8 @@ avm,fritzbox-4040)
ucidef_set_led_switch "lan" "LAN" "green:lan" "switch0" "0x1e"
;;
avm,fritzbox-7530 |\
glinet,gl-b1300)
glinet,gl-b1300 |\
mikrotik,lhgg-60ad)
ucidef_set_led_wlan "wlan" "WLAN" "green:wlan" "phy0tpt"
;;
edgecore,oap100)

View File

@ -29,6 +29,7 @@ ipq40xx_setup_interfaces()
engenius,eap1300|\
engenius,emd1|\
meraki,mr33|\
mikrotik,lhgg-60ad|\
mikrotik,sxtsq-5-ac|\
netgear,ex6100v2|\
netgear,ex6150v2|\
@ -190,6 +191,7 @@ ipq40xx_setup_macs()
lan_mac=$(macaddr_add $wan_mac 1)
label_mac="$wan_mac"
;;
mikrotik,lhgg-60ad|\
mikrotik,sxtsq-5-ac)
lan_mac=$(cat /sys/firmware/mikrotik/hard_config/mac_base)
label_mac="$lan_mac"

View File

@ -133,6 +133,7 @@ platform_do_upgrade() {
nand_do_upgrade "$1"
;;
mikrotik,hap-ac2|\
mikrotik,lhgg-60ad|\
mikrotik,sxtsq-5-ac)
[ "$(rootfs_type)" = "tmpfs" ] && mtd erase firmware
default_do_upgrade "$1"

View File

@ -0,0 +1,269 @@
/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
* Copyright (c) 2019, Robert Marko <robimarko@gmail.com>
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
* copyright notice and this permission notice appear in all copies.
*
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*
*/
#include "qcom-ipq4019.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/soc/qcom,tcsr.h>
/ {
model = "Mikrotik Wireless Wire Dish LHGG-60ad";
compatible = "mikrotik,lhgg-60ad";
memory {
device_type = "memory";
reg = <0x80000000 0x10000000>;
};
chosen {
stdout-path = "serial0:115200n8";
};
aliases {
led-boot = &user;
led-failsafe = &user;
led-running = &user;
led-upgrade = &user;
};
soc {
rng@22000 {
status = "okay";
};
mdio@90000 {
status = "okay";
/delete-node/ ethernet-phy@1;
/delete-node/ ethernet-phy@2;
/delete-node/ ethernet-phy@3;
/delete-node/ ethernet-phy@4;
/delete-node/ psgmii-phy@5;
};
counter@4a1000 {
compatible = "qcom,qca-gcnt";
reg = <0x4a1000 0x4>;
};
tcsr@1949000 {
compatible = "qcom,tcsr";
reg = <0x1949000 0x100>;
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
};
ess_tcsr@1953000 {
compatible = "qcom,tcsr";
reg = <0x1953000 0x1000>;
qcom,ess-interface-select = <TCSR_ESS_PSGMII_RGMII5>;
};
tcsr@1957000 {
compatible = "qcom,tcsr";
reg = <0x1957000 0x100>;
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
};
crypto@8e3a000 {
status = "okay";
};
watchdog@b017000 {
status = "okay";
};
ess-switch@c000000 {
switch_mac_mode = <0x3>; /* mac mode for RGMII RMII */
switch_lan_bmp = <0x0>; /* lan port bitmap */
switch_wan_bmp = <0x10>; /* wan port bitmap */
};
edma@c080000 {
status = "okay";
phy-mode = "rgmii-id";
qcom,num_gmac = <1>;
qcom,single-phy;
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
leds {
compatible = "gpio-leds";
power: power {
label = "blue:power";
gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
default-state = "keep";
panic-indicator;
};
user: user {
label = "yellow:user";
gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
};
wlan {
label = "green:wlan";
gpios = <&tlmm 58 GPIO_ACTIVE_HIGH>;
};
align-left {
label = "green:align-left";
gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
};
align-right {
label = "green:align-right";
gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
};
wlan-rx {
label = "green:align-down";
gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
};
wlan-tx {
label = "green:align-up";
gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
};
};
};
&tlmm {
serial_pins: serial_pinmux {
mux {
pins = "gpio60", "gpio61";
function = "blsp_uart0";
bias-disable;
};
};
spi_0_pins: spi-0-pinmux {
pinmux {
function = "blsp_spi0";
pins = "gpio13", "gpio14", "gpio15";
bias-disable;
};
pinmux_cs {
function = "gpio";
pins = "gpio12";
bias-disable;
output-high;
};
};
};
&blsp_dma {
status = "okay";
};
&blsp1_spi1 {
pinctrl-0 = <&spi_0_pins>;
pinctrl-names = "default";
cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
status = "okay";
m25p80@0 {
reg = <0>;
compatible = "jedec,spi-nor";
spi-max-frequency = <24000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "Qualcomm";
reg = <0x0 0x80000>;
read-only;
};
partition@80000 {
compatible = "mikrotik,routerboot-partitions";
#address-cells = <1>;
#size-cells = <1>;
label = "RouterBoot";
reg = <0x80000 0x80000>;
read-only;
hard_config {
read-only;
size = <0x2000>;
};
dtb_config {
read-only;
};
soft_config {
};
};
partition@100000 {
compatible = "mikrotik,minor";
label = "firmware";
reg = <0x100000 0xf00000>;
};
};
};
};
&blsp1_uart1 {
pinctrl-0 = <&serial_pins>;
pinctrl-names = "default";
status = "okay";
};
&cryptobam {
status = "okay";
};
&pcie0 {
status = "okay";
perst-gpio = <&tlmm 42 GPIO_ACTIVE_HIGH>;
bridge@0,0 {
reg = <0x00000000 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
ranges;
/* wil6210 802.11ad card */
wifi: wifi@1,0 {
status = "okay";
/* wil6210 driver has no compatible */
reg = <0x00010000 0 0 0 0>;
};
};
};
&gmac0 {
qcom,phy_mdio_addr = <0>;
qcom,poll_required = <1>;
vlan_tag = <0 0x20>;
};

View File

@ -40,6 +40,14 @@ define Device/mikrotik_hap-ac3
endef
TARGET_DEVICES += mikrotik_hap-ac3
define Device/mikrotik_lhgg-60ad
$(call Device/mikrotik_nor)
DEVICE_MODEL := Wireless Wire Dish LHGG-60ad
DEVICE_DTS := qcom-ipq4019-lhgg-60ad
DEVICE_PACKAGES += -kmod-ath10k-ct -ath10k-firmware-qca4019-ct kmod-wil6210
endef
TARGET_DEVICES += mikrotik_lhgg-60ad
define Device/mikrotik_sxtsq-5-ac
$(call Device/mikrotik_nor)
DEVICE_MODEL := SXTsq 5 ac (RBSXTsqG-5acD)

View File

@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -902,11 +902,69 @@ dtb-$(CONFIG_ARCH_QCOM) += \
@@ -902,11 +902,70 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@ -58,6 +58,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
+ qcom-ipq4019-habanero-dvk.dtb \
+ qcom-ipq4019-hap-ac3.dtb \
+ qcom-ipq4019-map-ac2200.dtb \
+ qcom-ipq4019-lhgg-60ad.dtb \
+ qcom-ipq4019-mr8300.dtb \
+ qcom-ipq4019-pa2200.dtb \
+ qcom-ipq4019-r619ac-64m.dtb \

View File

@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -837,11 +837,67 @@ dtb-$(CONFIG_ARCH_QCOM) += \
@@ -837,11 +837,68 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@ -55,6 +55,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
+ qcom-ipq4019-fritzrepeater-3000.dtb \
+ qcom-ipq4019-hap-ac3.dtb \
+ qcom-ipq4019-map-ac2200.dtb \
+ qcom-ipq4019-lhgg-60ad.dtb \
+ qcom-ipq4019-mr8300.dtb \
+ qcom-ipq4019-e2600ac-c1.dtb \
+ qcom-ipq4019-e2600ac-c2.dtb \