ramips: add support for Edimax Gemini RE23S

Hardware
--------
SoC:   Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM:   128MB
FLASH: 16MB NOR (Macronix MX25L12805D)
ETH:   1x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
  - 2.4GHz: 1x MT7615 (4x4:4)
  - 5GHz:   1x MT7615 (4x4:4)
  - 4 antennas: 2 external detachable and 2 internal
BTN:
  - 1x Reset button
  - 1x WPS button
LEDS:
  - 1x Green led (Power)
  - 1x Green-Amber-Red led (Wifi)
UART:
  - 57600-8-N-1

Everything works correctly.

Installation
------------
Flash the factory image directly from OEM web interface.
(You can login using these credentials: admin/1234)

Restore OEM Firmware
--------------------
Flash the OEM "bin" firmware directly from LUCI.
The firmware is downloadable from the OEM web page.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Restoring procedure tested with RE23_1.08.bin

MAC addresses
-------------
factory 0x4     *:24
factory 0x8004  *:25
Cimage  0x07    *:24
Cimage  0x0D    *:24
Cimage  0x13    *:24
Cimage  0x19    *:25

No other addresses were found in factory partition.

Since the label contains both the 2.4GHz and 5GHz mac address I decided
to set the 5GHz one as label-mac-device. Moreover it also corresponds
to the lan mac address.

Notes
-----
The wifi led in the OEM firmware changes colour depending on the signal
strength. This can be done in OpenWrt but just for one interface.
So for now will not be any default action for this led.

If you want to open the case, pay attention to the antenna placed on
the bottom part of the front cover.
The wire is a bit short and it breaks easily. (I broke it)

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[fix two typos and add extended MAC address section to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit is contained in:
Davide Fioravanti 2020-05-20 01:27:56 +02:00 committed by Adrian Schmutzler
parent 66e04abbb6
commit 8c13ebd3ad
3 changed files with 191 additions and 9 deletions

View File

@ -0,0 +1,163 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "mt7621.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "edimax,re23s", "mediatek,mt7621-soc";
model = "Edimax RE23S";
aliases {
led-boot = &led_power;
led-failsafe = &led_wifi_red;
led-running = &led_power;
led-upgrade = &led_power;
label-mac-device = &gmac0;
};
chosen {
bootargs = "console=ttyS0,57600";
};
leds {
compatible = "gpio-leds";
led_power: power {
label = "re23s:green:power";
gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
};
wifi_green {
label = "re23s:green:wifi";
gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
};
wifi_amber {
label = "re23s:amber:wifi";
gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
};
led_wifi_red: wifi_red {
label = "re23s:red:wifi";
gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
};
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <50000000>;
m25p,fast-read;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "bootloader";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "config";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x10000>;
read-only;
};
partition@50000 {
label = "cimage";
reg = <0x50000 0x20000>;
read-only;
};
partition@70000 {
compatible = "edimax,uimage";
label = "firmware";
reg = <0x70000 0xf50000>;
};
partition@fc0000 {
label = "freespace";
reg = <0xfc0000 0x40000>;
read-only;
};
};
};
};
&pcie {
status = "okay";
};
&pcie0 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x0>;
ieee80211-freq-limit = <2400000 2500000>;
};
};
&pcie1 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x8000>;
ieee80211-freq-limit = <5000000 6000000>;
};
};
&gmac0 {
mtd-mac-address = <&factory 0x8004>;
};
&switch0 {
ports {
port@4 {
status = "okay";
label = "lan";
};
};
};
&state_default {
gpio {
groups = "uart3", "uart2", "jtag", "wdt";
function = "gpio";
};
};
&xhci {
status = "disabled";
};

View File

@ -261,6 +261,24 @@ define Device/edimax_ra21s
endef
TARGET_DEVICES += edimax_ra21s
define Device/edimax_re23s
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 15680k
DEVICE_VENDOR := Edimax
DEVICE_MODEL := RE23S
DEVICE_ALT0_VENDOR := Edimax
DEVICE_ALT0_MODEL := Gemini RE23S
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | \
edimax-header -s CSYS -m RN76 -f 0x70000 -S 0x01100000 | pad-rootfs | \
append-metadata | check-size
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | append-rootfs | \
edimax-header -s CSYS -m RN76 -f 0x70000 -S 0x01100000 | pad-rootfs | \
check-size
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware wpad-basic
endef
TARGET_DEVICES += edimax_re23s
define Device/edimax_rg21s
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Edimax

View File

@ -19,6 +19,16 @@ ramips_setup_interfaces()
xiaomi,mir3g-v2)
ucidef_set_interfaces_lan_wan "lan1 lan2" "wan"
;;
edimax,re23s|\
mikrotik,routerboard-m11g|\
netgear,ex6150|\
thunder,timecloud|\
tplink,re350-v1|\
tplink,re500-v1|\
tplink,re650-v1|\
ubnt,unifi-nanohd)
ucidef_set_interface_lan "lan"
;;
gehua,ghl-r-001|\
hiwifi,hc5962|\
xiaomi,mir3p|\
@ -33,15 +43,6 @@ ramips_setup_interfaces()
netgear,wac104)
ucidef_set_interface_lan "lan1 lan2 lan3 lan4"
;;
mikrotik,routerboard-m11g|\
netgear,ex6150|\
thunder,timecloud|\
tplink,re350-v1|\
tplink,re500-v1|\
tplink,re650-v1|\
ubnt,unifi-nanohd)
ucidef_set_interface_lan "lan"
;;
mikrotik,routerboard-750gr3)
ucidef_set_interfaces_lan_wan "lan2 lan3 lan4 lan5" "wan"
;;